Acnodes FPC 6150 User manual

PC6150 /
FPC6150
15” TFT Touch
Panel Computer
User’s Manual

1
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. ACNODES Co., Ltd. assumes no responsibility for any
infringements of patents or other rights of third parties, which may result from
its use.
ACNODES assumes no responsibility for any inaccuracies that may be
contained in this document. ACNODES makes no commitment to update or
to keep current the information contained in this manual.
ACNODES reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
ACNODES Co., Ltd.
♥ Copyright 2006 by ACNODES Co., Ltd.
All rights reserved.

m CE Marking
m FCC Class A
Safety Approvals
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.ou

1
Safety Precautions
Before getting started, read the following important cautions.
1. The PC6150 / FPC6150 does not come equipped with
an operating system. An operating system must be loaded
first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the PC6150 / FPC6150
before making any installation. Be sure both the system
and the external devices are turned OFF. Sudden surge
of power could ruin sensitive
components. Make sure the
PC6150 / FPC6150 is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The PC6150 / FPC6150 may come
with or w/o a touch screen. Although the touch screen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touch screen, you
must follow the same procedure and not spray any cleaner
on the flat panel directly.
6. Avoid using sharp objects to operate the touch screen.
Scratches on the touch screen may cause malfunction or
internal failure to the touch screen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the PC6150 / FPC6150, make sure it
is securely installed.

5. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
 Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds.
This will help to discharge any static electricity on your body.
 When handling boards and components, wear a
wrist-grounding strap, available
from most electronic
component stores.
Trademarks Acknowledgments
ACNODES is a trademark of ACNODES Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties of their
respective owners.

3
This page does not contain any information.

Table of Contents
Disclaimers.......................................................................ii
Safety Approvals .........................................................iii
FCC Compliance .............................................................iii
Safety Precaut i ons ...................................................... iv
C h a p t e r 1 .............................................................. 1
Introduct i on .................................................................. 1
1.1 General Description ...........................................1
1.2 Specifications .....................................................2
1.2.1 Main CPU board...................................................2
1.2.2 I/O System............................................................3
1.2.3 System Specification..........................................4
1.3 Dimensions .........................................................5
1.4 Front View and I/O Outlets ................................7
1.4.1 Front View............................................................7
1.4.2 I/O Outlet..............................................................8
1.5 Package list.........................................................9
C h a p t e r 2 ............................................................ 10
Hardware Installat i on ................................................. 10
2.1 CPU and DRAM Installation.............................10
2.2 HDD Installation................................................12
2.3 CD-ROM Installation.........................................14
2.4 Add-on Card Installation..................................15
2.5 Serial Port Interface .........................................16
2.6 VGA....................................................................16
2.7 Ethernet.............................................................17
2.8 Mountings: Panel/ Desktop/ Rack...................18
2.8.1 Desktop Kit Assembly......................................18
2.8.2 Panel-mount Kit Assembly ..............................19
2.8.3 Rack mounting Assembly................................20
C h a p t e r 3............................................................22
Table of Contents vii

Driver Insta l lation ....................................................... 22
3.1 System...............................................................22
3.2 Touch Screen....................................................23
3.2.1 Specification......................................................23
3.2.2 Driver Installation-
Windows2000/XP/CE.NET/XP-Embedded......24
3.2.3 Driver Installation- DOS....................................26
C h a p t e r 4 ............................................................ 30
Embedded O.S . Installat i on ...................................... 30
4.1 Windows XP Embedded ..................................30
4.1.1 PenMount Touch Screen..................................30
4.2 Windows CE.NET 4.2 .......................................31
4.2.1 Calibration Touch Screen ................................31
A p p e n d i x A ....................................................... 32
SBC BIOS Setup ............................................... 32
A.1 BIOS Introduction.................................................32
A.2 BIOS Setup............................................................32
A.2.1 Standard CMOS Setup......................................34
A.2.2 Advanced BIOS Features.................................37
A.2.3 Advanced Chipset Features ............................41
A.2.4 Integrated Peripherals......................................43
A.2.5 Power Management Setup...............................46
A.2.6 PNP/PCI Configuration.....................................49
A.2.7 PC Health Status...............................................50
A.2.8 Frequency/Voltage Control..............................51
A.2.9 Load Fail-Safe Defaults....................................52
A.2.10 Load Optimized Defaults..................................53
A.2.11 Set Supervisor/User Password .......................54
A.2.12 Save & Exit Setup .............................................55
A.2.13 Exit Without Saving..........................................56
Appendix B .................................................................57
Power Supply Specification ......................................57
B.1 Power Supply: FSP180-50PLA1
(180W, AC 110~230V Input) ........57
viii Table of Contents

B.1.1 ELECTRICAL REQUIREMENTS.......................57
B.1.2 EFFICIENCY ......................................................60
B.1.3 ENVIRONMENTAL REQUIREMENTS...............60
B.1.4 TEMPERATURE RANGE...................................60
B.1.5 HUMIDITY ..........................................................60
B.1.6 VIBRATION ........................................................60
B.1.7 SHOCK...............................................................61
B.1.8 SAFETY..............................................................61
B.1.9 MTBF..................................................................61
B.2 Power Supply: MPI-810H-A1
(ATX120W, AC 90~260V Input) ...62
B.2.1 Input Specifications..........................................62
B.2.2 Output Specifications.......................................62
B.2.3 General Specifications.....................................63
B.2.4 Environmental Specifications..........................63
B.2.5 International Standards....................................63
B.3 Power Supply: MPD-810H
(ATX120W, DC 10~30V Input) .....64
B.3.1 Input Specifications..........................................64
B.3.2 Output Specifications.......................................64
B.3.3 General Specifications.....................................65
B.3.4 Environmental Specifications..........................65
B.3.5 International Standards....................................65
Table of Contents ix

Introduction 1
PC 6150/FPC6150 User
’
s
Manual
C h a p t e r 1
Introduction
This chapter contains the general information and the detail
specifications of the PC6150 / FPC6150. Chapter 1 includes
the following sections:
f General Description
f System Specification
f Dimensions
f Front View & I/O Outlets
f Package List
1.1 General Description
The PC6150 / FPC6150 is a TFT Touch Panel PC which equipped
with superior Pentium
® M/Celeron ® M processors, 15" XGA LCD
display, and 2 PCI expansion slots. The paradigmatic
industrial panel computer, PC6150 / FPC6150, is a complete full-
function and extreme cost-effective industrial HMI controller.
The PC6150 / FPC6150 fits in with Aluminum IP65/NEMA4
compliant front bezel. To provide flexible expansion slots for
users, the PC6150 / FPC6150 also provides 2 PCI expansion slots for
add-on cards extended.
This ideal industrial-grade panel computer PC6150 / FPC6150 can
be applied to the several of industrial or commercial projects, such
as transportation, factory automation, HMI machine controller, Point
Of Sales, KIOSK and more. Moreover, PC6150 / FPC6150 provides
highly reliable and highly flexible industrial-grade products in
all-in-one solutions.

2 Introduction
PC 6150 / FPC 6150 User
’
s Manual
1.2 Specifications
1.2.1 Main CPU board
f CPU: Socket 479 for
Intel
® Pentium ® M FPC 6150
Intel
® Celeron ®
Processors PC 6150
f System Chipset: Intel
® 852GM+ICH*4
f BIOS: Phoenix-Award BIOS, Y2K compliant
4Mbit Flash, DMI, Plug and Play
SmartView for multiple LCD type selection, display
mode option and application extension features
RPL/PXE Ethernet Boot ROM
“Load Optimized Default” to backup customized
Setting in the BIOS flash chip to prevent from CMOS
battery fail
f System Memory: One 184-pin DDR SDRAM DIMM
Maximum DDR of up to 1GB DDR266
f L2 Cache: integrated in CPU
f Bus Clock: 400 MHz
f Watchdog Timer: Up to 255 levels as Reset feature

PC 6150/FPC6150 User
’
s
Introduction 3
Manual
1.2.2 I/ O System
f Standard I/O:
−3 x serial ports with power; 3 x RS-232
−1 x PS/2 for Keyboard Interface
−1 x PS/2 for Mouse Interface
−4 x USB Ports 2.0 compliant
−1 x 15 pin(female) for VGA output
f Ethernet:
One Realtek 8100C PCI Bus 10/100M Base-T
One Realtek 8110SC with Giga LAN
Wake On LAN (via ATX power supply)
Equipped with RJ-45 interface
Optional with Realtek RTL8110S for 10/100/1000 Base-T
f Audio:
Realtek AC’97 codec audio
MIC-in, Line-in, Line-out
f Onboard IDE:
2 parallel ATA-100 as 1 * 44-pin 2.0 pitch box-header and
1 * 40-pin 2.0 pitch box-header.
PATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra
DMA/33/66/100.
f Compact Flash Socket:
One Compact Flash Type II Socket (Optional)
f Expansion Slots:
One 32-bit PCI slot for 2 Masters

PC 6150 / FPC 6150 User
’
4 Introduction
s Manual
1.2.3 System Specif i cation
f 15” TFT LCD
f Disk drive housing:
−1x optional slim type CD-ROM dive,
−1x optional slim type FDD dive,
−1 x internal 3.5” drive (or 2 X 2.5” HDD)
f AC/DC power supply
f Heat dispensing design
f Two slot for PCI expansion
f Net weight:
−13.3 Kgs
f Dimension (main body size):
−472 x 365 x 127.4mm
f Operating temperature:
−O° to 45°C ; Relative umidity:50%
f Relative humidity:
−10% to 85% @ 40° C, non-condensing
f Altitude:
−10,000 ft. (3,000 meters)
f Vibration (operating):
−5 to 500 Hz, 1 G random
f Shock (operating):
−10 G peak acceleration (11 msec. duration)

Introduction 5
PC 6150/FPC6150 User
’
s
Manual
1.3 Dimensions
The following diagrams show the dimensions and outlines of
PC6150 / FPC6150.

6 Introduction
PC 6150 / FPC 6150 User
’
s Manual

Introduction 7
PC 6150/FPC6150 User
’
s
Manual
1.4 Front View and I/O Outlets
1.4.1 Front View
The figure below shows the features and controls on the
PC6150 /FPC6150 front panel.
1: SEL-
2: SEL+
3: Backlight ON/OFF

8 Introduction
PC 6150 / FPC 6150 User
’
s Manual
1.4.2 I /O Out l et
The following figure shows the I/O locations of the PC6150/FPC6150.
1: COM 3 6: COM 1 & 2
2: LAN 7: VGA
3: Mic-in, Line-in, Line-Out 8: USB v2.0 * 4
4: Power Switch 9: PCI Slot * 2
5: PS2 x 2 (KB/MS) 10: AC power