Acnodes PCH3782 User manual

PCH3582/3782/3982
15/17/19 inch Atom Fanless Panel PC
User Manual
PCH3582/3782/3982:15/17/19”IndustrialFanlessPanelPC
withAtomD525processor
14628 Central Ave,
Chino, CA 91710
tel:[phone], fax:[phone]
© Copyright 2013 Acnodes, Inc.
All rights reserved. Product description and product specifications
are subject to change without notice. For latest product
information, please visit Acnodes’web site at www.acnodes.com.

Warning!_______________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions manual, it may cause interference to radio
communications.
It has been tested and found to comply with the limits for a Class A computing device pursuant to
FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely to
cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard –Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.

Packing List
Accessories (as ticked) included in this package are:
□ AC power cable
□ Driver & manual CD disc
□ Other._ (please specify)
Safety Precautions
Follow the messages below to avoid your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don’t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
◆ Disconnect power when you change any hardware devices. For instance, when you
connect a jumper or install any cards, a surge of power may damage the electronic
components or the whole system.

Table of Contents
Wa
r n i ng !… ………………………………………………………………………….……..….2
Packing List...................................................................................................................3
Safety Precautions........................................................................................................3
Chapter 1 Getting Started
1.1 Specifications………………………………………….………….……...…..6
1.2 Dimensions…………………………………...……………….…………......8
1.3 Brief Description of PCH3X82……….………………….………………12
Chapter 2 Hardware Installation
2.1 Mainboard Specifications………………………..…………….…………13
2.2 Jumpers Setting and Connectors………………………….……………17
Chapter 3 BIOS Setup
3.1 Operations after POST Screen.............................................................26
3.2 BIOS SETUP UTILITY................................................................27
3.3 System Overview.......................................................................28
3.4 Advanced Settings................................................................... 29
3.5 Advanced PCI/PnP Settings................................................................ 37
3.6 Boot Settings....................................................................................... 40
3.7 Security Settings.................................................................................. 42
3.8 Advanced Chipset Settings.................................................................. 43
3.9 Exit Options..........................................................................................49
3.10 Examples of GPIO Programming.......................................................50
Chapter 4 Installation of Drivers

4.1 Chipset Driver.…………………………...…………………………………59
4.2 GMA 3150 VGA Chipset Driver..…....…......………………..............…..62
4.3 Network adapter Driver……..................................………………….….66
4.4 Realtek HD Audio Driver Installation………………….…………………69
Chapter 5 Touch Screen Installation
5.1 Introduction to Touch Screen Controller Board………………………....72
5.2 Windows 2000/XP USB Driver Installation………………….………..….72
Figures
Figure 1.1: Dimensions of PCH3582…………….....……………………...9
Figure 1.2: Dimensions of PCH3782……………..……...………………..10
Figure 1.3: Dimensions of PCH3982………………………...………………..11
Figure 1.4: Overview of PCH3X82 ……..….………………………...12
Figure 2.1: Mainboard Overview……………………………………..……..…13
Figure 2.2: Mainboard Dimensions……………………………………………13
Figure 2.3: Jumpers and Connectors Location-TOP…………………...……14
Figure 2.4: Jumpers and Connectors Location- Bottom………………….…14
Figure 5.1: Bird‟s Eye View of Control Board…………………………….......72

Chapter 1 Getting Started
1.1 Specifications
Model No.
Specs
PCH3582
PCH3782
PCH3982
System
Processor
Atom D525 1.8GHz processor FSB 800MHz
System Chipset
ICH8M Chipset
System Memory
1 x 204 Pin SO-DIMM DDR3 800GHz, up to 2GB SDRAM
Storage
1 x 2 .5" SATA HDD Space
1 x CF Internal Slot
1 x CF External Slot for option (except APC-3282/3283)
External I/O Port
4XUSB 2.0
2XGbE RJ-45 LAN port
1XDB-15 VGA (disable for use)
1XDB-9 RS422/485(default RS-485)
1XDB-9 RS-232
1XDC Power input T/B connector
7 Pin T/B for 2in/out/1Ground/Switch±
Expansion Slots
None
OSD
OSD control
Brightness/ Screen and Touch on/off /Power on/off
(APC-3782/3783/3982/3983 add auto tune function key)
OS support
Windows XP Pro, XP Embedded, Windows Embedded Standard 7
LCD
Display Type
1
2
.
1
”
T
F
T
-
L
C
D
15”TFT-LCD
17”TFT-LCD
19”TFT-LCD
Max. Resolution
8
0
0
x
6
0
0
1024x768
1280x1024
1280x1024
Max. Color
262K
Luminance (cd/m2)
3
5
0
400
350
350
ViewAngle
H
:
1
3
0
°
/
V
:
1
1
0
°
H:160 ° / V:140 ° (APC-
3582) H:140 ° / V:110 °
(APC-3583)
H:170
° / V:160 °
H:160
° / V:160 °
Backlight Lifetime
50,000 hrs
Touch Screen
Type
Resistive Touch
Light Transmission
80%
Power Supply
Power Input
DC 11~32V

Mechanical
Construction
Stainless Steel Housing (APC-3X82) / Steel Housing (APC-3X83)
IP Rating
Front Panel IP65 / 6 sides IP42 with waterproof kit
Mounting
V
E
S
A
7
5
x
7
5
M
o
u
n
t
VESA 75x75
Mount
VESA 75x75
Mount
VESA 100x100
Mount
Dimensions (WxHxD)
3
3
5
(
W
)
x
2
6
5
(
H
)
x
6
7
(
D
)
m
m
399(W)x324(H)x
67(D) mm
432(W)x358(H)x
66.8(D)mm
470(W)x388.6(H)x
67(D)mm
Environmental
Operating Temperature
0~50 ﾟC
Storage Temperature
-20~60 ﾟC
Storage Humidity
10~90% @40 ﾟC non-condensing
Certificate
CE/FCC Class A

1.2 Dimensions
Figure 1.1: Dimensions of PCH3582

Figure 1.2: Dimensions of PCH3782

Figure 1.3: Dimensions of PCH3982

1.3 Brief Description of PCH3X82
The fanless PCH3X82 is Atom D525 powered panel PC with a rich variety of functions and peripherals.
PCH3X82 is designed for easy and simplified integration into various vehicle applications. It
comes with a compact flash slot, 2.5-inch hard disk drive, DDR3 memory, audio jack, 2 Ethernet, DC
input. 4 external USB ports ensure simplified connectivity to a variety of external peripheral
devices. The unit supports Windows XP Pro, XP Embedded and Windows Embedded Standard
7. The fanless touch panel computer is ideal for use as Web Browser, Terminal and HMI at
all levels of automation control.
Figure 1.4: Overview of PCH3X82

Chapter 2 Hardware Installation
2.1 Mainboard Specifications
Figure 2.1: Mainboard Overview
Figure 2.2: Mainboard Dimensions

Figure 2.3: Jumpers and Connectors Location-TOP
Figure 2.4: Jumpers and Connectors Location-Bottom

Specifications
Board Size 165mm x 115mm
CPU Support Atom D525 /1.80GHz (onboard)
Atom N455 /1.66GHz (onboard option）
Chipset Atom D525 + ICH8M
Atom N455 + ICH8M (option）
Atom N455 +ICH8M-E (option, Support RAID0/1）
Memory
Support 1x SO-DIMM (204pins), up to 2GB DDR3 800MHz FSB
Graphics Integrated by D525 / N455 GMA 3150
Super I/O Winbond W83627UHG
BIOS AMIBIOS
Storage 3 x SATA Connector
1 x Compact Flash II Slot (shared IDE)
Network 2 x RJ-45 1000Mbps LAN Intel 82574L
4 x USB 2.0 stack port for external
USB
Serial
2 x USB 2.0 internal Pin header
2 x USB 2.0 internal for mini PCIe
1 x RS232 port, DB9 connector for external (COM1),
pin 9 w/5V/12V/Ring select
1 x RS232/422/485 select header for internal (COM3), default
RS232
4 x RS232 (COM2,COM4,COM5,COM6), header internal
Digital I/O 8-bit digital I/O by Pin header
4-bit digital Input
4-bit digital Output
Battery Support CR2477 Li battery by 2-pin header
Audio Support Audio via Realtek ALC662 HD audio decoder
Support Line-in, Line-out, MIC by 2x5-pin header
Keyboard
/Mouse 1x PS2 keyboard/mouse by 1x6 box pin header
Expansion Bus 1x PC 104+ connector (PCI master 4, jumper for +3.3V & 5V
select)
2x mini-PCI-express slot (1x full size, 1x half-size )
Power
Management DC12V input
1 x 2-pin power input connector

Front I/O by 2x5-pin header
Power on/off switch
Reset switch
Power LED status
HDD LED status
Buzzer
Watchdog
Timer
External I/O
port
Temperature
Software programmable 1 –255 second by Super I/O
1 x COM Port (COM1)
4 x USB 2.0 Ports (stack)
2 x RJ45 GbE Ports (10/100/1000Mbps)
1 x DB15 Port or 2x8 Pin Header
Operating: -20℃–70℃
Storage: -40℃–85℃
Humidity 5% - 95%, non-condensing, operating
Power
Consumption 12V /1.6A (D525 processor with 2GB DDR3 DRAM) 12V /1.3A (N455 processor with 2GB DDR3 DRAM)
EMI/EMS Meet CE/FCC class A

2.2 Jumpers Setting and Connectors
1. JCLR_CMOS: (2.0mm Pitch 1x3 Pin Header)CMOS clear jumper, CMOS clear
operation will permanently reset old BIOS settings to factory defaults.
JCLR_CMOS
CMOS
CLOSE 1-2
NORMAL
(default)
CLOSE 2-3
Clear CMOS
Procedures of CMOS clear:
5.4.1.1 Turn off the system and unplug the power cord from the power outlet.
5.4.1.2 To clear the CMOS settings, use the jumper cap to close pins 2 and 3 for about
3 seconds then reinstall the jumper clip back to pins 1 and 2.
5.4.1.3 Power on the system again.
5.4.1.4 When entering the POST screen, press the <F1> or <DEL> key to enter CMOS
Setup Utility to load optimal defaults.
5.4.1.5 After the above operations, save changes and exit BIOS Setup.
2. JVCCIO: (2.0mm Pitch 1x3 Pin Header) PC104+ port voltage selection jumper,select
voltage for PCI-104 Plus device. The default for this jumper is “ a ll open”,meaning
the user must select the voltage to be used.
JVCCIO
PC104+ VCCIO
Voltage
CLOSE 1-2
+3.3V
CLOSE 2-3
+5V
all Open
(Default)
3. BZ: onboard buzzer.
4. JCOM6: (2.0mm Pitch 1x3 Pin Header) COM6 setting jumper, pin 1~3 are used to
select signal out of pin 10 of COM6 port.
JP1 Pin#
Function
Close 1-2
COM6 Pin10=+5V (default)
Close 2-3
COM6 Pin10=+12V (option)
5. JP2: (2.0mm Pitch 1X2 Pin Header), ATX Power and Power auto on setting jumper.
JP2 Mode

Open
ATX Power Mode
Close
Power Auto on (Default)
6. BAT: (1.25mm Pitch 1x2 box Pin Header) 3.0V Li battery is embedded to provide
power for CMOS.
Pin#
Signal
Name
Pin1
VBAT
PIN2
Ground
7. F_PANEL: (2.0mm Pitch 2X5 Pin Header), Front panel connector.
Signal Name
Pin#
Pin#
Signal Name
HD LED+
1
2
POWER
LED+
HD LED-
3
4
POWER LED-
Ground
5
6
PWRBTN
RESET
7
8
Ground
BUZZER+
9
10
BUZZER-
Pin1-3: HDD LED, They are used to connect hard disk activity LED. The LED blinks
when the hard disk is reading or writing data.
Pin2-4: POWER LED, They are used to connect power LED. When the system is
powered on or under S0/S1 state, the LED is normally on; when the
system is under S4/S5 state, the LED is off.
Pin5-6: POWER on/off Button, They are used to connect power switch button.
The two pins are disconnected under normal condition. You may short
them temporarily to realize system startup & shutdown or awaken the
system from sleep state.
Pin7-8: RESET Button, They are used to connect reset button. The two pins are
dis-
connected under normal condition. You may short them temporarily to
realize
system reset.
Pin9-10: BUZZER, They are used to connect an external buzzer.
Note:
When connecting LEDs and buzzer, pay special attention to the signal
polarity. Make sure that the connector pins have a one-to-one
correspondence with chassis wiring, or it may cause boot up failure.

8. USB3: (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB
ports via a dedicated USB cable, speed up to 480Mb/s.
Signal Name
Pin#
Pin#
Signal Name
+5V
1
2
+5V
USB_P6_DN
3
4
USB_P7_DN
USB_P6_DP
5
6
USB_P7_DP
Ground
7
8
Ground
NC
9
10
Ground
Note:
Before connection, make sure that pinout of the USB Cable is in accordance with that
of the said tables.Any inconformity may cause system down and even hardware
damages.
9. JCOM: (2.0mm Pitch 2x6 Pin Header) COM1 and COM3 setting jumper, pin 1~6 are
used to select signal out of pin 9 of COM1 port; pin 7~12 are used to select output type
for COM3 port (RS232 Type or RS422 Type or RS485 Type).
JCOM Pin#
Function
CLOSE 1-2
COM1 Pin9=RI （default）
CLOSE 3-4
COM1 Pin9=+5V (option)
CLOSE 5-6
COM1 Pin9=+12V (option)
CLOSE 7-9
COM3 FOR RS232 FROM COM3
（default）
CLOSE 8-10
COM3 FOR RS485 FROM COM33
(option)
CLOSE 10-12
COM3 FOR RS422 FROM COM33
(option)
Note:
Since COM3 and COM33 use the same address, they cannot work at the same time.
10. GPIO: (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides
a group of self-programming interfaces to customers for flexible use.
Signal Name
Pin#
Pin#
Signal Name
GPIO20
1
2
GPIO60

GPIO21
3
4
GPIO61
GPIO22
5
6
GPIO62
GPIO23
7
8
GPIO63
Ground
9
10
+5V
11. COM3: (2.0mm Pitch 1x4 box Pin Header),it provides selectable RS422/RS485
serial signal output.
RS422 Type (option)
RS485 Type (option)
Signal Name
Pin#
Pin#
Signal Name
422RXD-
1
1
NC
422RXD+
2
2
NC
422TXD-
3
3
485A-
422TXD+
4
4
485A+
Note:
Use COM3 RS232/RS485 Function, please setting JCOM Jumpers and BIOS CMOS
Setup.
Path:
BIOS Setup Utility \ Advanced Setting \ SuperIO Configuration \ Serial Port3
Type:[RS232 Type]
[RS485 Type]
12. F_AUDIO: (2.0mm Pitch 2x5 Pin Header), Front Audio, An onboard Realtek
ALC662 codec is used to provide high-quality audio I/O ports. Line Out can be
connected to a headphone or amplifier. Line In is used for the connection of external
audio source via a Line in cable. MIC is the port for microphone input audio.
Signal Name
Pin#
Pin#
Signal Name
FRONT-OUT-L
1
2
LINEIN_R
AUD_AGND
3
4
AUD_AGND
FRONT-OUT-R
5
6
LINEIN_L
AUD_AGND
7
8
AUD_AGND
FRONT-MIC_L
9
10
FRONT-MIC_
R
13. COM2-COM6: (2.0mm Pitch 2x5 Pin Header),COM2 COM3 COM4 COM5 COM6
Ports, up to 5 standard RS232 ports are provided. They can be used directly via COM
cable connection.

COM2,COM3,COM4,COM5 Signal Name:
Signal
Name
Pin#
Pin#
Signal Name
DCD
1
2
RXD
TXD
3
4
DTR
Ground
5
6
DSR
RTS
7
8
CTS
RI
9
10
NC
COM6 Signal Name:
Signal
Name
Pin#
Pin#
Signal Name
DCD
1
2
RXD
TXD
3
4
DTR
Ground
5
6
DSR
RTS
7
8
CTS
RI
9
10
JCOM6 Setting:
Pin1-2 : 5V
(Default)
Pin2-3:12V
(option)
Note:
COM3 port is controlled by pins No.7~10 of JCOM. For details, please refer to
description of JCOM and COM33 BIOS Setup.
14. KB/MS: (2.0mm Pitch 1x6 box Pin Header), PS/2 keyboard and mouse port, the
port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct
used.
Pin#
Signal
Name
1
KBDATA
2
MSDATA
3
Ground
4
+5V
5
KBCLK
6
MSCLK
15. USB1/2: (Double stack USB type A), Rear USB connector, it provides up to 4