Acrel ATE Series User manual

安科瑞电气股份有限公司
322
ATE 系列无线测温传感器
ATE series Wireless Temperature Sensor
安装说明 V2.2
Installation Instruction V2.2
安科瑞电气股份有限公司
Acrel Co., Ltd.

安科瑞电气股份有限公司
申 明
DECLARATION
版权所有，未经本公司之书面许可，此手册中任何段落，章节内容均不得被摘抄、拷贝或以任何形式复
制、传播，否则一切后果由违者自负。
本公司保留一切法律权利。
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of our
company. The violator will bear the dependent legal responsibility.
We reserve all the rights.
本公司保留对本手册所描述之产品规格进行修改的权利，恕不另行通知。
订货前，请垂询当地代理商以获悉本产品的最新规格。
We reserve all the rights to revise product specification without notice. Please consult local agent
to get the latest information of our products specification.

安科瑞电气股份有限公司
目 录
Contents
ATE 系列无线测温传感器 ..............................................................................................................................1
ATE series Wireless Temperature Sensor .........................................................................................................1
安科瑞电气股份有限公司 .............................................................................................................................. 1
1安装指南 ...................................................................................................................................................... 1
1 Installation Guide .......................................................................................................................................... 1
1.1 产品概述 ........................................................................................................................................... 1
1.1 Product Introduction ...........................................................................................................................1
1.2 型号说明 ........................................................................................................................................... 1
1.2 Type Introduction ............................................................................................................................... 1
1.3 技术指标 ........................................................................................................................................... 2
1.3 Technical Features .............................................................................................................................. 2
1.4 产品安装 ........................................................................................................................................... 4
1.4 Product Installation .............................................................................................................................4

安科瑞电气股份有限公司
1
1安装指南
1 Installation Guide
1.1 产品概述
1.1 Product Introduction
ATE 系列无线测温传感器根据 《NB/T 42086-2016 无线测温装置技术要求》 开发，可用于
3~35kV 户内开关柜，包括中置柜、手车柜、固定柜、环网柜等多种开关柜；也可用于 0.4kV 低压
柜，包括固定柜，抽屉柜等。无线测温传感器可安装于柜内任何发热点上，利用无线数据传输技术
实时发送监测数据，再通过接收装置将温度数据传输到显示装置或者远程监控系统。
ATE series wireless temperature measuring sensor has been developed in compliance with
Specification for Wireless Temperature Measuring equipment, NB/T 42086-2016. It is suitable for 3-35kV
indoor switchgears, including built-in switchgears, handcart switchgears, fixed switchgears and loop-net
switchgears. It is also suitable for 0.4kV low-voltage switchgears such as fixed switchgears and drawer
switchgears. The wireless temperature sensors can be installed at any heating point in switchgears, the
device utilizes the wireless data transmission technology for real-time transmission of monitored
temperature data. In addition, it can be transmitted to display device or remote intelligent monitoring
system.
1.2 型号说明
1.2 Type Introduction
ATE
表示无线测温传感器
Wireless temperature measuring sensor
XXX
型号：
Type:
100 表示螺栓式，100M 表示磁吸式，200
表示表带式，400 表示合金片固定，100P
表示户外螺栓式，200P 表示户外表带式，
300M 表示多回路式
100 is bolted, 100M is magnetic,200 is belt,
400 is tied with cable tie, 100P is outdoor
bolted, 200P is outdoor belt，300M is multi
loop

安科瑞电气股份有限公司
2
1.3 技术指标
1.3 Technical Features
项目
Items
指标
Features
环境要求
Environment
工作温度
Temperature
-40℃~85℃
相对湿度
Humidity
≤95%
大气压力
atmospheric pressure
86kPa~106kPa
ATE100M/100/200
有源无线温度传感
器
ATE100M/100/200
Active wireless
temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷 150m（470Mhz）、空旷 50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
25s
发射频率
Transmitting frequency
25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
磁吸式/螺栓式/表带式
Magnetic / bolted /Belt
测温范围
Range of temperature
-50℃~+125℃
精度
Precision
±1℃
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
电池寿命
Battery life
≥5年(25℃)
≥5 years(25℃)
400 无源无线温度
传感器
400 Passive
wireless
temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷 150m（470Mhz）、空旷 50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
15s
发射频率
Transmission frequency
15s
工作电源
Power source
CT 感应取电，启动电流≥5A
CT-powered, starting current≥5A
最大工作电流(Max current)≤5000A

安科瑞电气股份有限公司
3
安装方式
Installation
合金片固定
alloy chip fixing
传感器探头
Sensor probe
合金底座
alloy bottom
测温范围
Range of temperature
-50℃~125℃
精度
Precision
±1℃
应用范围
Application
高低压柜内电气接头
Joints in high or low voltage switchgears
ATE100P/200P 户
外无线温度传感器
ATE100P/200P
Outdoor wireless
temperature sensor
无线频率
Wireless frequency
470MHz、433Mhz
通讯距离
Communication distance
空旷 150m（470Mhz）、空旷 50m（433Mhz）
150m(470Mhz) 、50m(433Mhz)in open area
采样频率
Sampling frequency
25s
发射频率
Transmitting frequency
25s-5min
工作电源
Power source
电池
Battery
安装方式
Installation
螺栓式/表带式
bolted /Belt
测温范围
Range of temperature
-50℃~+150℃
精度
Precision
±0.5℃
应用范围
Application
电气接头
Voltage switchgears
电池寿命
Battery life
≥5年(25℃)
≥5 years(25℃)
防护等级
Protection level
IP68
ATE300M 多回路
式温度传感器
ATE300M multi
Loop temperature
sensor
无线频率
Wireless frequency
433-510MHz
通讯距离
Communication distance
空旷 1000m
1000m in open area
采集频率
Sampling frequency
1-240s
工作电源
Power source
AC/DC 85~265V
安装方式
Installation
导轨式/扎带式
测温范围
Range of temperature
-40℃~+140℃

安科瑞电气股份有限公司
4
1.4 产品安装
1.4 Product Installation
无线温度传感器共有多种型号，分别对应磁吸固定、螺栓固定、表带固定、合金片固定等安装
方式。
There are several types of wireless temperature sensors and mounting methods correspondingly, i.e.
Magnetic , bolted , belt and alloy chip fixing.
1.4.1 外形尺寸
1.4.1 Shape Size
ATE100M
ATE100/ATE100P
精度
Precision
±1℃
应用范围
Application
低压抽屉柜内电气接头
Joints in low voltage switchgears

安科瑞电气股份有限公司
5
ATE200/ATE200P
ATE400
ATE300M

安科瑞电气股份有限公司
6
1.4.2 标签说明
1.4.2 Label Instructions
1.4.2.1 ATE 传感器搭配 ASD/ARTM-Pn 装置
1.4.2.1 ATE sensor with ASD/ARTM-Pn device
ASD/ARTM-Pn
ATE400
ATE100
ATE100M
ATE200
ATE200P
ATE100P
如 果 安 装 ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P ， 其 组 号 应 与 显 示 装 置
ASD/ARTM-Pn 的标签组号一致，安装位置依照标签文字安装，“编码：1A”为安装第一个 A相，
“编码：1B”为安装第一个 B相，以此类推。
If the sensor is ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P, the number behind “组号
（Group）：” should be the same as ASD/ARTM-Pn, the sequence of installation is base on the label, “编
码（Code）：1A” is first one on the phase A, “编码（Code）：1B” is first one on the phase B，and so
on.
注意：出厂时包装箱内无线温度传感器与显示装置已配对，不可以与其他显示装置或无线温度
传感器混用，无线温度传感器按照标签安装。
Notice: wireless temperature sensors and display device in the package have been matched
before delivery. Do not use them with other display device or other wireless temperature sensors
together. Please installing them with label on the sensor.
1.4.2.2 ATE 传感器搭配 ATC600-C/ATC450-C 收发器
1.4.2.2 ATE sensor with ATC600-C/ATC450-C coordinator

安科瑞电气股份有限公司
7
ATC450-C
ATC600-C
ATE400
ATE100
ATE100M
ATE200
ATE200P
ATE100P
如图所示，如果安装 ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P ， 其 组 号 应 与
ATC450-C/ATC600-C 的组号一致，安装位置依照标签文字安装，“编码：001”建议安装在第一个
柜子的第一个测温点，再依次按照测温点顺序安装。
According to the above pictures, If the sensor is ATE100M/100/200/400/100P/200P, the group
number of ATE must be same as the group number of ATC450-C/ATC600-C and the installation order is
base on the label. The code of each sensor is used to distingguish each sensor from same group. “编码
（code）: 001”is recommended to be installed on the first temperature measuring point of the first cabinet,
and then installed other sensors in this order.
1.4.2.3 ATE300M 传感器搭配 ATC600-M 收发器
1.4.2.3 ATE300M sensor with ATC600-M coordinator
如果安装 ATE300M 传感器，其组号应与 ATC600-M 的组号一致，安装位置依照标签文字安装，
“编码：001”建议安装在第一个柜内，再依次按照测温点顺序安装。
If the sensor is ATE300M, the group number of ATE must be same with the group number of
ATC600-M and the installation order is base on the label. The code of each sensor is used to distingguish
each sensor from same group. “编码（code）: 001”is recommended to be installed on the first cabinet,
若有特殊情况，请联系相关工程师进行沟通解决。
ATE300M
ATE600-M

安科瑞电气股份有限公司
8
In case of any special situation, please contact the relevant engineers for communication.
1.4.3 安装方法
1.4.3 Installation Method
1.4.3.1 ATE100M 安装方法
1.4.3.1 ATE100M Installation Method
ATE100M 磁吸式无线测温传感器适用于铁质的电气节点或设备表面。
The magnetic wireless sensor ATE100M is suitable for iron electrical nodes or equipment surfaces.
磁吸式无线温度传感器 ATE100M 结构说明：
Structure introduction of ATE100M:
1 —— 无线温度传感器主体 The core of wireless temperature sensor ATE100M
2—— 测温部位 Thermo-sensitive part
3 —— 电池开关 battery switch
2
1
1
3
1
直接吸附在铁质测温点处，安装前打开电池开关，电源指示灯闪烁两次。安装实例见下图：
Adsorbed directly at the iron temperature measuring point, open the battery switch before installation,
the power indicator flashes twice. The installation examples see images below.
1.4.3.2 ATE100 安装方法
1.4.3.2 ATE100 Installation Method
ATE100 螺栓式无线测温传感器适用于电缆与母排搭接处，电缆与隔离刀闸搭接处。
The bolted type wireless sensor ATE100 is suitable for use at joints between cable and bus bar and
joints between cable and disconnector.
ATE100 螺栓式无线温度传感器结构说明：
ATE100 structure introduction:
1 —— 无线温度传感器主体 The core of wireless temperature sensor ATE100
2 —— 测温部位 Thermo-sensitive part
3 —— 电池开关 battery switch

安科瑞电气股份有限公司
9
3
1
2
1
拆下安装位置搭接处的螺丝，将传感器固定在安装位置，对准合金底板的开孔，然后旋紧螺丝
固定，安装前打开电池开关，电源指示灯闪烁两次。安装实例见下图：
Remove the screw from the joints, and fixing the sensor on the position with the hole on the alloy
baseplate, then tighten the screw, open the battery switch before installation, the power indicator flashes
twice. The installation examples see images below.
1.4.3.3 ATE200 安装方法
1.4.3.3 ATE200 Installation Method
ATE200 表带式无线测温传感器适用于断路器动触头、静触头、电缆接头、母排等处。
The strap-secured type called ATE200 is suitable for use at moving contacts and fixed contacts of
breaker, cable joints and bus bar.
表带式无线温度传感器结构说明:
ATE200 structure introduction:
1 —— 无线温度传感器主体，测温探头在背面 The core of wireless temperature sensor ATE200,
temperature measuring probe is on the other side
2 —— 表带及锁扣 strap and hasp
3 —— 电池开关 battery switch

安科瑞电气股份有限公司
10
1
3
1
2
将传感器主体固定在安装位置，将表带绕过安装母排或者触头穿过表带，表带头收紧，最后将
表带尾用锁扣锁紧。表带过长可以剪掉多余部分，表带过短可以联系我司增订。安装前打开电池开
关，电源指示灯闪烁两次。安装实例见下图：
注：ATE200 可安装静触头，铜排，电缆头。
Fixing the body of sensor on the position, then strapping it on the bus bar or breaker contact and
frapping it through the hole on the strap, fixing the strap by hasp. Clipping the strap if it is too long when
finished, if it is too short, contacting us for strap parts before installation. Open the battery switch before
installation, the power indicator flashes twice.The installation examples see images below.
Note: ATE200 can be installed with fixed contact, copper plate and cable head.
1.4.3.4 ATE400 安装方法
1.4.3.4 ATE400 Installation Method
ATE400 迷你型无线温度传感器适用于动触头，母排，电缆，母排、电缆搭接处等多种场合。
The mini type called ATE400 is suitable for using at moving contacts, bus bars, cables and joints
between bus bar and cable.
迷你型无源无线温度传感器结构说明：
Mini type passive temperature sensor structure introduction:
1 —— 温度传感器主体 The core of wireless temperature sensor ATE400
2 —— 合金底座，与温度探头接触 alloy bottom, touched with temperature probe
3 —— 锁扣，用于固定合金片 metal hasp, for fixing alloy chip
4 —— 取电合金片，用于感应取电 alloy chip, for CT-powered
5 —— 硅胶垫片，用于支撑合金片 silicone gasket, used to support the alloy chip
6 —— 合金片安装孔，用于安装合金片 alloy chip hole, used to install the alloy chip

安科瑞电气股份有限公司
11
2
1
6
5
1
3
1
4
1
1
取2根合金片穿过锁紧件安装孔，将合金片居中对折后锁紧件固定在折弯处；将对折后的 4层
合金片分别穿过硅胶垫片-传感器主体-硅胶垫片；将整体传感器环绕安装部位一圈后拉紧合金片并
旋紧螺丝；合金片多余部分留取适当长度并折叠压紧。合金片安装示意过程如下：
注：ATE400 可安装静触头，铜排，电缆头;如需安装动触头，需要考虑梅花头及套筒高度是否
足够。
Firstly, take 2pieces of alloy chips through the mounting hole of metal hasp, meanwhile fold the alloy
chips and fix the metal hasp in the middle of alloy chips. Secondly, take the folded alloy chips through one
silicone gasket, the core of ATE400 and another silicone gasket in turn.Thirdly, circle the whole alloy chips
around the mounting position and tension the alloy chips, then tighten the screw on the metal hasp. Finally,
subtract the excess alloy chips. The complete installation process is shown in Figures 1 to 4.
Note: ATE400 can be installed with fixed contact, copper plate and cable head; If it is necessary to
install moving contacts, it is necessary to consider the height of plum blossom head and sleeve is sufficient.

安科瑞电气股份有限公司
12
ATE400 无线温度传感器安装实例如下：
The wireless temperature sensor called ATE400 installation examples, see images below.
1.4.3.5 ATE300M 安装方法
1.4.3.5 ATE300M Installation Method
ATE300M 多回路式温度传感器适用于低压柜内电气接头等多种场合。
Ate300M multi circuit temperature sensor is applicable to various occasions such as electrical
connectors in low-voltage cabinet.
将传感器主体在柜内合适位置通过导轨或者扎带捆绑的方式固定好，拆下安装位置搭接处的螺
丝，将 NTC 探头套入接头位置，然后旋紧螺丝固定。用 AC/DC 85~265V 电源给传感器供电，上电
时电源指示灯红灯闪烁 2次。
Fix the sensor body at the proper position in the cabinet by means of guide rail or binding tape,
remove the screws at the overlapping position of the installation position, put the NTC probe into the joint
position, and then tighten the screws for fixation. Use AC / DC 85 ~ 265V power supply to supply power
to the sensor. The red light of the power indicator flashes 2 times when the power is on .
.

安科瑞电气股份有限公司
13
Headquarters: Acrel Co., LTD.
Sales engineer: Augustus Yang
Address: No.253 Yulv Road Jiading District, Shanghai，China
Mobile/Whatsapp/Wechat: [phone]
Skype: rayyang11081
Website: www.acrel.sg
Email: [email protected]
Postcode: 201801