Acrosser Technology AR-B1666A User manual

Page 1of 3AR-B1666AManual
AR-B1666AMANUAL
Version 1.0
1. SETTING UP THE SYSTEM
TOP PLACEMENT
BOTTOM PLACEMENT
1.1 PACKING LIST
nThe quick setup manual
n1AR-B1666ACPU board
n1 Software utility CD
n1 Mini Din power adapter
1.2 KEYBOARD & MOUSE CONNECTOR (KB1)
1.3 SDRAM SOCKET 144 PIN (DIMM1)
11144
144 pin SO-DIMM
1.4 HARD DISK (IDE) CONNECTOR (IDE1)
※44 Pin Hard Disk Connector (IDE1)
1 43
2 44
Pin # Signal Name
1MOUSE DATA
2KB DATA
3GND
4VCC
5MOUSE CLOCK
1
66KB CLOCK
KB
Pin Signal Pin Signal
1-RESET 2GROUND
3DATA 7 4DATA 8
5DATA 6 6DATA 9
7DATA 5 8DATA 10
9DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 NOT USED
21 IDEDREQ 22 GROUND
23 -IOW A 24 GROUND
25 -IOR A 26 GROUND
27 IDEIORDYA 28 GROUND
29 -DACKA 30 GROUND
31 AINT 32 GROUND
33 SA 1 34 Not Used
35 SA 0 36 SA 2
37 CS 0 38 CS 1
39 HD LED A 40 GROUND
41 VCC 42 VCC
43 GROUND 44 Not Used

Page 2of 3AR-B1666AManual
1.5 CRT CONNECTOR (VGA1)
1 9
2 10
1.6 USB CONNECTOR (USB2)
nUSB2
1 9
2 10
1.7 SERIAL PORT (COM1, COM2)
A. COM1
USED RS232
COM1
6
7
8
9
1 2
3
4 5
9.GND
10.X
1.DCD
2.DSR
3.RX
4.RTS
5.TX
6.CTS
7.DTR
8.RI
B. COM2
1 9
2 10
1.8 FAN POWER CONNECTOR (FAN1)
3 2 1
1. GND
2. +12V
3. Fan Speed
1.9 INTERNAL BUZZER (BUZ1)
1.+ 2.-
1.10 POWER/HD (LED5)
1.11LAN LED (LED1, LED2, LED3, LED4.)
1
2
1:10 / 100M
2: ACT
1.12ETHERNET RJ-45 CONNECTOR
(LAN1, LAN2, LAN3, LAN4)
1
8
Pin # Signal Name Pin # Signal Name
1RED 6AGND
2AGND 7V.S
3GREEN 8SCL
4GND 9H.S
5BLUE 10 SDA
Pin # Signal Name Pin # Signal Name
1VCC 6DATA3+
2VCC 7GND
3DATA2-8GND
4DATA3-9GND
5DATA2+ 10 GND
PIN (CN8) FUNCTION
1TPTX+
2TPTX -
3TPRX+
4Not Used
5Not Used
6TPRX-
7Not Used
8Not Used

Page 3of 3AR-B1666AManual
1.13RESET BUTTON (RST1)
SW
SW PUSHBUTTON
1 2
1.14POWER CONNECTOR (PWR1&PWR2)
A.PWR1:
3
8
5
6
PWR3
KB-PS/2MINIDING6F_D90
35
68
GNDGND
+5V+12V
B:PWR2:
1
2
1: +12V
2: GND
3: GND
4: +5V
3
4
C: POWER SWITCH(J1)
1.15MINI PCI SLOT (PCI1)
On board one mini PCI slot (PCI1)
1.16GPIO PORT (GPIO1)
16 1.VCC3
2.GPIOA
3.GPIOB
5.GPIOD
4.GPIOC
6.GND
1.17COMPACT FLASH SLOT (CF1)
Pin assignment is showed below.
1.18 CF MASTER/SLAVE MODE SELECT (J2)
This 2-pins jumper will decide the CF operating in
master/slave mode.
1.19 CLEAR CMOS JUMPER (JBAT1)
1 2 3
Jumper Function
Open OFF
Short ON
Jumper Function
Open (Factory Preset) Slave
Short Master
Jumper Function
(1-2) Keep Data (Factory Preset)
(2-3) Clear Data