Acrosser Technology AR-B6002 Installation guide

AR-B6002 Quick Manual
1 220010413-G
AR-B6002 Quick Manual
2 220010413-G
AR-B6002 Quick Manual V1.1
1. Main board illustration (Top Side)
CN6 CN18 CN23,CN24
CN8 GPIO1 JP8,JP11
SATA_PWR1 CN5 CN25 (Reserve)
SATA_PWR2 CN7 COM5 (Reserve)
CN2 CN28 JP5,JP6 (Reserve)
CN13 CN20 JP7,JP10
BH1 VGA1 JP9,JP12
Minipcie1 SW1 U8
CN9 (Reserve) COM1 CN21
CN10 (Reserve) COM3 DIMM1
Minipcie2 AUDIO1 SATA1
CN17 PWR1 SATA2
LED1 FUSE1

AR-B6002 Quick Manual
3 220010413-G
Main board illustration (Bottom Side)
CF1
AR-B6002 Quick Manual
4 220010413-G
2. Connectors and Jumpers Setting
1. CN6: BLUETOOTH connector. 2. CN8: GPS connector.
PIN DEFINE
1 GND
2 USB_D+
3 USB_D-
4 +3.3V
5 LED
6 BT_ON
7 GND
8 +3.3V
PIN DEFINE
1 GND
2 USB_D+
3 USB_D-
4 +3.3V
5 LED
6 GPS_ON
7 GND
8 +3.3V
3. SATA_PWR1: SATA Power connector 4. SATA_PWR2: SATA Power connector
PIN DEFINE
1 +12V
2 GND
3 +3.3V
4 +5V
PIN DEFINE
1 +12V
2 GND
3 +3.3V
4 +5V
5. CN2: Pin Header for clear CMOS 6. CN13: SIM Card Slot
STATUS SETTING
1-2 Clear CMOS
SIM card slot for 3G module.
7. BH1: CMOS battery holder 8. MINIPCIE1: Mini PCI-E connector. (for 3.5G
module)
CMOS battery holder
MINI PCI-E connector

AR-B6002 Quick Manual
5 220010413-G
9. CN9: Internal USB2.0 connector (Reserve) 10. CN10: Internal USB2.0 connector (Reserve)
PIN DEFINE
1 +5V
2 USB5-
3 USB5+
4 GND
5 GND
PIN DEFINE
1 +5V
2 USB6-
3 USB6+
4 GND
5 GND
11. MINIPCIE2: Mini PCI-E connector. 12. CN17: FPGA Programmable HEADER.
MINI PCI-E connector.
FPGA programmable header.
13. LED1: Power State 14. CN18: CANBUS connector
LED SIGNAL
G PIC LED
G HDD LED
Y Power LED
PIN DEFINE
1 CAN_H
2 CAN_L
15. GPIO1: GPIO connector 16. CN5: RJ45 + USB X 2 connector
PIN DEFINE PIN DEFINE
1 GPO0 2 GPO1
3 GPO2 4 GPO3
5 GND 6 GND
7 GND 8 GND
9 GND 10 GND
11 GPI4 12 GPI5
13 GPI6 14 GPI7
15 N.C
RJ45 connector for Gigabit Ethernet port
#1.
Upper: Port #2.
Lower: Port #1.
AR-B6002 Quick Manual
6 220010413-G
17. CN7: USB connector 18. CN28: PIC Programming connector.
Upper: Port #4.
Lower: Port #3.
PIC programming connector.
19. CN20: Setting Voltage level of Battery 20. VGA1: D-SUB-15 female connector for
VGA output
STATUS SETTING
1-2 +24V
2-3 +12V (Default).
D-SUB-15 female connector for
VGA output
21. SW1: DIP switch for power mode select
(Note 1) 22. COM1: D-SUB-9P Male connector × 2 (Note 2)
Mode 1 2 3 4
0 ON ON ON ON
1 ON ON ON OFF
2 ON ON OFF ON
3 ON ON OFF OFF
4 ON OFF ON ON
5 ON OFF ON OFF
6 ON OFF OFF ON
7 ON OFF OFF OFF
PIN DEFINE PIN DEFINE
1 DCD
/DT- 2 SIN
/DT+
3 SOUT
/422R+ 4 DTR
/422R-
5 GND 6 DSR
7 RTS 8 CTS
9 RI_12V
23. COM3: D-SUB-9P Male connector X 2 24. AUDIO1: AUDIO connector
PIN DEFINE PIN DEFINE
1 DCD 2 SIN
3 SOUT 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9 RI_12V
Color SIGNAL
Blue Remote Switch
Green Line Out
Pink MIC IN

AR-B6002 Quick Manual
7 220010413-G
25. PWR1: Power Input Terminal Block
Connector 26. FUSE1: Fuse connector
PIN DEFINE
1 12V / 24V
2 IGN
3 GND
PIN DEFINE
1,2 Fuse Out
3,4 Fuse In
27. CN23: RI SELECT for COM1/2
CN24: RI SELECT for COM3/4 28. JP8,JP11: RS-232 / RS-422 / RS-485
Selection for COM1/2 (Note 2)
STATUS SETTING
RI#
(Default) 1-2(COM1/COM3)
+12V 3-4( COM1/COM3)
RI#
(Default) 5-6( COM2/COM4)
+12V 7-8( COM2/COM4)
STATUS SETTING
RS-232
(Default)
1-3
2-4
RS-422 3-5
4-6
RS-485 3-5
4-6
29. CN25: RI SELECT for COM5/6 (Reserve) 30. COM5: RS232 signal connector for port #5
(Reserve)
STATUS SETTING
RI#
(Default) 1-2(COM5)
+12V 3-4(COM5)
RI#
(Default) 5-6(COM6)
+12V 7-8(COM6)
PIN DEFINE PIN DEFINE
1 DCD #5 2 DSR #5
3 RX #5 4 RTS #5
5 TX #5 6 CTS #5
7 DTR #5 8 RI #5
9 GND 10 N.C
31. JP5,JP6: RS-485 Termination 120 ohm
(Reserve) 32. JP7,JP10: RS-232 / RS-422 / RS-485 Selection for COM1/2 (Note 2)
STATUS SETTING
Enable short
Disable open
(Default)
STATUS SETTING
RS-232
(Default) 1-2
RS-422 3-4
RS-485 5-6
AR-B6002 Quick Manual
8 220010413-G
33. JP9,JP12: RS-232 / RS-422 / RS-485
Selection for COM1/2 (Note 2) 34. U8: SPI BIOS Socket
STATUS SETTING
RS-232
(Default)
1-3
2-4
RS-422 3-5
4-6
RS-485 N / A
SPI BIOS Socket
35. CN21: BIOS Programmable HEADER.36. DIMM1: DDR-II SODIMM Socket.
PIN DEFINE PIN DEFINE
1 CS0 2 +3.3V
3 MISO 4 HOLD
5 WP 6 CLK
7 GND 8 MOSI
9 N.C 10 N.C
DDR-3 SODIMM Socket
37. SATA1: SATA device connector #1. 38. SATA2: SATA device connector #2.
SATA device connector #1 SATA device connector #2
39. CF1: Type-II compact flash card socket
+3.3V CF card only and UDMA
mode supported

AR-B6002 Quick Manual
9 220010413-G
Note1: (Detail functions please reference to User Manual.)
Mode0: ATX function.
Mode1: Auto PWRBTN function.
Mode2, Mode3, Mode4: Smart ATX.
Mode5, Mode6, Mode7: Smart ATX (poweron by trigger Remote SW).
Others modes are reserved for test only.
Note2: COM1 / 2 to choose RS-232 / RS-485 / RS-422 by Jump setting
JP7, JP8, JP9 setting to COM1.
JP10, JP11, JP12 setting to COM2.
Note3: GPIO and CAN BUS cable color
PIN Color PIN Color
1 Brown 2 Orange
3 Green 4 Blue
5/6/9 Black 8 White
7 Red/White 10 Purple
11 Light Green 12 Light Blue
13 Pink 14 Brown/White
15 Yellow
PIN Color
1 white
2 purple