SOLTEK SL-65MIV User manual

R
The Soul Of Computer Technology
SL-65MIV/65MIV2/65MIV-X/65MIV2-X V1.1
USER MANUAL

USER NOTICE
Product Model : SL-65MIV/65MIV2/
65MIV-X/65MIV2-X
Manual Revision : V1.1
Release Date : anuary 2001
• Intel, Celeron, Pentium II, Pentium III are trademarks of Intel Corporation.
• VIA, PM133, APOLLO PRO 133, VT 2C694X and VT 2C6 6A are trademarks of VIA
Corporation.
• S3 Savage4 is tademarks of S3 Corporation.
• Norton AntiVirus, Norton Ghost are trademarks of Symantec Corporation.
his Users Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the
motherboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek computer inc. Provides this manual “As is “ without warranty
of any kind, either express or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for
a particular purpose. In no event shall Soltek computer inc. Be li-
able for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek computer inc. Has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 2 Soltek Computer Inc. All Rights Reserved.
T

SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chin, Taipei-
Hsien, Taiwan, R.O.C.
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOLTEK KOREA INC.
Address : 1002, Chungjin Bldg. 53-5 Wonhyo-Ro, 3-Ka,
Yongsan-Ku Seoul 140-113, Korea
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
SOUL TECHNOLOGY EUROPE B.V.
Address : Sydneystraat 52-54 3047 BP Rotterdam, the Nether-
lands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com

4
65MIV/65MIV2/65MIV-X/65MIV2-X
C O N T E N T
CHAPTER 1 INTRODUCTION ........................................................... 6
1-1 ITEMLIST CHECKUP ............................................................................. 6
1-2 CPU ........................................................................................................ 6
1-3 CHIPSET ................................................................................................ 6
1-4 BIOS ....................................................................................................... 6
1-5 EXTENSION SLOTS .............................................................................. 6
1-6 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER................ 7
1-7 MULTI-I/O FUNCTION ........................................................................... 7
1- INTEGRATED SAVAGE4 2D/3D/VIDEO ACCELERATOR .................... 7
1-9 SOUND CONTROLLER ......................................................................... 7
1-10 FULL FEATURED ACCELERATED GRAPHICS PORT (AGP)
CONTROLLER .....................................................................................
1-11 POWER MANAGEMENT .....................................................................
1-12 FROM FACTOR ...................................................................................
1-13 HARDWARE MONITORING ................................................................
1-14 OTHERS ..............................................................................................
1-15.1 MOTHERBOARD LAYOUT --- 65MIV ............................................... 9
1-15.2 MOTHERBOARD LAYOUT --- 65MIV2 ........................................... 10
1-16 FLAT PANEL DESKTOP MONITOR SUPPORT ................................ 11
1-17 HIGH SCREEN RESOLUTION CRT SUPPORT ............................... 11
1-1 CHIPSET DIAGRAM .......................................................................... 12
1-19 MOTHERBOARD SPECIFICATION TABLE OF 65MIV/65MIV2 ........ 13
CHAPTER 2 HARDWARE SETUP................................................... 16
2-1 CPU INSTALLATION ............................................................................ 16
2-2 MEMORY INSTALLATION ................................................................... 17
2-3 HDD/FDD INSTALLATION ................................................................... 1
2-4.1 CPU BUS RATIO SELECT ................................................................ 19
2-4.2 BUS CLOCK SELECT ....................................................................... 19
2-5 JUMPER DEFINITIONS ....................................................................... 20
2-5.1 ONBOARD FAN (JFAN1/JFAN2) ...................................................... 20
2-5.2 USB PORT SELECT (JP4/JP5) ........................................................ 20
2-5.3 POWER LOST RESUME (JP9)......................................................... 21
2-5.4 CLEAR CMOS DATA (JBAT1) ........................................................... 21
2-5.5 WAKE ON LAN (WOL) FUNCTION (WLO1) ..................................... 21
2-5.6 CD-ROM AUDIO CONNECTOR (JCD1/JCD2) ................................. 22
2-5.7 THERMAL SENSOR CONNECTOR (RT2) ....................................... 22
2-6 CONNECTORS .................................................................................... 23
2-6.1 J2 ....................................................................................................... 23

5
65MIV/65MIV2/65MIV-X/65MIV2-X
2-6.2 J3 ....................................................................................................... 25
2-6.3 CHASSIS PANEL CONNECTOR ...................................................... 26
2-6.4 FLAT-PANEL DISPLAY CONNECTOR (DVC1)................................. 27
2-6.5 ATX POWER SUPPLY CONNECTOR .............................................. 27
2-6.6 SECOND USB CONNECTOR........................................................... 2
2-6.7 SERIAL PORT CONNECTOR ........................................................... 29
2-6. PS/2 MOUSE AND PS/2 KEYBOARD .............................................. 29
2-6.9 IRQ DESCRIPTION .......................................................................... 30
2-7 VOICE DIANOSTIC FUNCTION --- ONLY FOR 65MIV-X/65MIV2-X ... 31
CHAPTER 3 SOFTWARE SETUP ................................................... 34
3-1 ABOUT THE SUPPORT CD ................................................................. 34
3-2 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ................... 34
3-3 ONBOARD S3® SAVAGE4TM VGA DRIVER INSTALLATION ............ 3
3-3.1 INSTALL PM133 VGA DRIVER FOR WINDOWS 95/9 /SE ............. 3
3-3.2 INSTALL PM133 VGA DRIVER FOR NT4.0 ..................................... 3
3-3.3INSTALL PM133 VGA DRIVER FOR WINDOWS ME ........................ 39
3-3.4 INSTALL S3® SAVAGE4TM VGA DRIVER WINDOWS 2000........... 39
3-4 AC’97 AUDIO CODEC INSTALLATION ................................................ 40
CHAPTER 4 BIOS SETUP ............................................................... 42
4-1 INTRODUCE THE BIOS ...................................................................... 42
4-2 WHAT IS BIOS SETUP ........................................................................ 42
4-3 HOW TO RUN BIOS SETUP ............................................................... 42
4-4 WHAT IS CMOS ................................................................................... 43
4-5 WHAT IS POST .................................................................................... 43
4-6 BIOS UPGRADE .................................................................................. 43
4-6.1 BEFORE UPGRADE BIOS ............................................................... 43
4-6.2 UPGRADE PROCESS ...................................................................... 44
4-7 CMOS SETUP UTILITY ....................................................................... 47
4- STANDARD CMOS SETUP ................................................................. 4
4-9 ADVANCED BIOS FEATURES ............................................................ 51
4-10 ADVANCED CHIPSET FEATURES ................................................... 56
4-11 INTEGRATED PERIPHERALS ........................................................... 62
4-12 POWER MANAGEMENT SETUP ...................................................... 67
4-13 PNP / PCI CONFIGURATION ............................................................ 73
4-14 PC HEALTH STATUS ......................................................................... 76
4-15 FREQUENCY/VOLTAGE CONTROL ................................................. 77
4-16 LOAD OPTIMIZED DEFAULTS .......................................................... 79
4-17 SET SUPERVISOR / USER PASSWORD ......................................... 79
4-1 SAVE & EXIT SETUP ......................................................................... 0
4-19 EXIT WITHOUT SAVING ................................................................... 0

6
65MIV/65MIV2/65MIV-X/65MIV2-X
CHAPTER 1
INTRODUCTION
1-1 ITEMLIST CHECKUP
• Motherboard
• Support CD
• User’s Manual
• Bundle Bonus Pack CD
• Bundle Bonus Pack Manual
• Temperature Sensor Cable
• ATA66/100 IDE Cable
• RS232 Cable
• FDD Cable
1-2 CPU
• Supports Intel® FC-PGA370 Pentium® III up to 1GHz, and FC-PGA370.
• Supports CeleronTM & PPGA370 Celeron processors up to 00MHz.
• Supports VIA Cyrix III processors up to 733MHz.
• Supports 66 to 200 MHz system bus speed.
• Supports processor voltage Auto-Detect circuit.
1-3 CHIPSET
• North Bridge - VIA 605 APOLLO PRO133A PM133.
• South Bridge - VIA VT 2C6 6A or VT 2C6 6B.
1-4 BIOS
• Award BIOS V6.0.
• Support Plug & Play V1.0.
• Flash Memory for easy upgrade.
• Supports BIOS writing protection.
• Year 2000 compliant.
1-5 EXTENSION SLOTS
• Three PCI bus Mater slots.
• One AGP 4x mode slot.
• Three DIMM slots.

7
65MIV/65MIV2/65MIV-X/65MIV2-X
1-6 ADVANCED HIGH-PERFORMANCE DRAM
CONTROLLER
• Supports PC133 and PC100 SDRAM and Virtual Channel Memory (VCM)
SDRAM up to 3 DIMMs.
• 64-bit data width and 3.3V DRAM interface.
• Supports up to 1.5 GB memory space.
• Different DRAM types may be used in mixed combinations.
• PCI-2.2 compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs .
1-7 MULTI-I/O FUNCTION
• Two Ultra DMA 33 / 66 Master Mode PCI EIDE ports (for 65MIV only).
• Two Ultra DMA-33 / 66 / 100 Master Mode PCI EIDE ports (for 65MIV2
only).
• Two UART’s for Complete Serial Ports.
• One dedicated IR connector:
Third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector:
Standard mode, ECP and EPP support.
• Floppy Disk connector:
Two FDDs with drive swap support.
• Universal Serial Bus connector:
--- USB v1.1 and Intel Universal HCI v1.1 compatible.
--- Provides 2 build-in USB ports (another 2 interal USB ports for extensible pur-
pose require an optional USB connect cable).
• PS/2 Keyboard connector.
• PS/2 Mouse connector.
1-8 INTEGRATED SAVAGE4 2D/3D/VIDEO ACCELERATOR
• Optimized Share Memory Architecture (SMA).
• 2 to 32MB frame buffer using system memory.
• Single cycle 12 -bit 3D architecture.
• Full AGP 4x, including sideband addressing and execute mode.
• Floating point triangle setup engine.
• M triangles/second setup engine.
• 140M pixels/second trilinear fill rate.
• 2D/3D resolutions up to 1920x1440.
1-9 SOUND CONTROLLER
• SoundBlaster Pro Hardware and Direct Sound Ready AC’97 Digital Audio
Controller with Codec Onboard.

8
65MIV/65MIV2/65MIV-X/65MIV2-X
1-1 FULL FEATURED ACCELERATED GRAPHICS PORT
(AGP) CONTROLLER
• Synchronous and pseudo-synchronous with the host CPU bus with optimal
skew control PCI AGP CPU Mode 33/66/100 MHz DDR 3x synchronous.
• Support 66MHz 1x/2x/4x modes for AD and SBA signaling.
• AGP v2.0 compliant.
1-11 POWER MANAGEMENT
• ACPI 1.0 compliant (Advanced Configuration and Power Interface).
• APM V1.2 compliant (Legacy power management).
• Supports ACPI suspend STR mode POS mode (Power On Suspend).
• Supports Wake On LAN (WOL) & Wake On Modem.
• Supports real time clock (RTC) with date alarm, month alarm, and century
field.
1-12 FROM FACTOR
• ATX from factor, 4 layers PCB.
• Motherboard size 22.0cm X24.5cm.
1-13 HARDWARE MONITORING
• Programmable control, status, monitor and alarm for flexible desktop
management (software include).
• Five-positive voltage monitoring.
• Two-temperature monitoring.
• Two Fan-speed monitoring.
1-14 OTHERS
• Clock generator supports 1MHz linear clock setting.

9
65MIV/65MIV2/65MIV-X/65MIV2-X
1-15.1 MOTHERBOARD LAYOUT --- 65MIV
• Default Setting: Intel Celeron 300A/66 MHz
13 13
JP4 JP5
13
JBAT1
13
JP9
JFAN2
JFAN1
WOL1
JCD1
JCD2
1 4
1 4
AGP 4X
PCI 1
PCI 2
PCI 3
DIMM1 DIMM2 DIMM3
FDD1
IDE2 IDE1
SOCKET 37
RT1
RT2
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97
Codec
Clock Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE PS/2 K/B
upper
lower
USB1 USB
upper
lower
VIA
VT86 5
VIA
VT82C
686A
COM2
DVC1
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC1 /PC133 SDRAM
1
1
1
J2 J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
++
--
+-
1 15 1 15

10
65MIV/65MIV2/65MIV-X/65MIV2-X
13 13
JP4 JP5
13
JBAT1
13
JP9
JFAN2
JFAN1
J2 J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
WOL1
JCD1
JCD2
1 4
1 4
AGP 4X
PCI 1
PCI 2
PCI 3
DIMM1 DIMM2 DIMM3
FDD1
IDE2 IDE1
SOCKET 37
RT1
RT2
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97
Codec
Clock Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE PS/2 K/B
upper
lower
USB1 USB
upper
lower
VIA
VT86 5
VIA
VT82C
686B
COM2
DVC1
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC1 /PC133 SDRAM
1
1
1
++
--
+-
1 15 1 15
1-15.2 MOTHERBOARD LAYOUT --- 65MIV2
• Default Setting: Intel Celeron 300A/66 MHz

11
65MIV/65MIV2/65MIV-X/65MIV2-X
1-17 HIGH SCREEN RESOLUTION CRT SUPPORT
Resolution Supported
System Memory Frame Buffer
Size (8MB Default)
640x4 0x /16/ 32 4MB MB 16/32MB
00x600x /16/ 32
1024x76 x /16/ 32
12 0x1024x
12 0x1024x16
12 0x1024x32
1600x1200x
1600x1200x16
1600x1200x32
1920x1440x
1920x1440x16
High Screen Resolution CRT Support
1-16 FLAT PANEL DESKTOP MONITOR SUPPORT
• The VT 605 / 6C370 has the capability of displaying graphics on TFT
flat panel desktop monitors using a 12-bit digital interface to an external
encoder. The VT 605 / 6C370 also supports autoexpansion and center-
ing of all VGA text and graphics modes to ensure that the entire flat panel
display will be utilized. All resolutions are supported up to 12 0 x 1024 by
flat panel desktop monitor. The resolution is Digital Visual Interface 1.0
specification compliant.

12
65MIV/65MIV2/65MIV-X/65MIV2-X
1-18 CHIPSET DIAGRAM
• The VT 605 is a high performance, cost-effective and energy efficient
SMA chip set for the implementation of AGP / PCI / LPC desktop personal
computer system with 66MHz, 100MHz, and 133MHz CPU host bus (“Front
Side Bus”) frequencies and based on 64-bit Socket-370 (Intel Pentium
III, Celeron) super-scalar processors. VT 605 is the VIA part number.
VT8605 System Block Diagram with VT82C686A or VT82C686B
PCI-TO-ISA South Bridge
ATA33/66 or
ATA33/66/1
4X USB
AGP 4X Expansion
Interface
VT82C
686A/
VT82C
686B
VT86 5
SMA NB
552-pin
PBGA
PCI Slots
33MHz,
32-bit PCI
64-bit 133/1 /66 MHz
133/1 /66 MHz
PC133/PC1 SDRAM
TV
Encoder
TMDS
Xmitter
Socket 37
Celeron/PIII
CPU
Serial Port
Floppy Disk
Parallel Port
EPROM
AC-97
LPC
Integrated
AC-97 Audio
AC-Link
FSB

13
65MIV/65MIV2/65MIV-X/65MIV2-X
Model
VIA VT82C686A VIA VT82C686B
65MIV
North bridge VIA VT86 5
South bridge
AGP Interface AGP 4X Mode
Build-in AC97 codec
Memory Supports PC133 and PC1 SDRAM and Virtual Channel
Memory (VCM) up to 1.5GB
3 DIMM Slots
Audio
IDE 2 x Ultra ATA33/66
IDE ports
2 x Ultra ATA33/66/1
IDE ports
I/O
Yes
Yes
4 x USB ports, 1 x FDD port, 2 x COM ports,
1 x LPT port, 1 x IrDA, 1 PS/2 Mouse, 1 PS/2 K/B
PCI slot 3 x PCI Master Slots
VD-Tech
Hardware
Monitoring
BIOS writing
Protection
Remark
65MIV2
On-chip
Graphics S3 SAVAGE 4 AGP 4X
Optional
1-19 MOTHERBOARD SPECIFICATION TABLE OF 65MIV/
65MIV2

14
65MIV/65MIV2/65MIV-X/65MIV2-X
ATTENTION !!!
1. Please refer to your processor installation or other
documentation attached with your CPU for detailed
installing instruction.
2. Installing a heat sink and cooling fan is necessary for
proper heat dissipation from your CPU. Uncorrected
installation may result in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct specifi-
cation both of CPU CLOCK and RATIO. Uncorrected
setting may cause damage to your CPU.

15
65MIV/65MIV2/65MIV-X/65MIV2-X
MEMO

16
65MIV/65MIV2/65MIV-X/65MIV2-X
CHAPTER 2
HARDWARE SETUP
2-1 CPU INSTALLATION
1. Pull the lever sidways away from the socket, and then raise the lever up
to a 90-degree angle.
2. Take note of the red circle as below picture. When insert the CPU into
socket, you can find out there is a definite pin orientation for CPU and
socket.
SOCKET 37
SOCKET 37
WARNING !!!
Never run you processor without the heat sink properly and firmly attached.
PERMANENT DAMAGE WILL RESULT!

17
65MIV/65MIV2/65MIV-X/65MIV2-X
SOCKET 37
3. Make sure that the CPU positions in the socket tightly, and then put the
lever down to complete the CPU installation.
WARING !!!
• Make sure that you unplug your power supply when adding or removing
memory modules or other system components, failure to do so may cause
severe damage to both your motherboard and expansion cards.
• Be careful when inserting or removing DIMM, forcing a DIMM in or out of a
socket can be damaged the memory module or the socket. Some of DIMMs
contain EDO or FTP DRAM that accept only 5V power. These DIMM types
are incompliant with the motherboard, the M/B only supports 3.3V true
SDRAM DIMMs.
Installing DIMM:
• Make sure you have the correct memory module type for your motherboard.
• Insert the module(s) as shown, DIMMs have 16 -pins and two notches that
will match with the onboard DIMM socket, memory modules are installed by
inserting them straight into the slot until they “click” into place. They only fit
in one direction so do not force them into place.
2-2 MEMORY INSTALLATION
Removing:
• Press the holding clips on both sides of socket out ward to release the
DIMM, Gently pull the DIMM out of the socket.
168-Pin DIMM Notch Key Definitions(3.3V)
DRAM Key Position Voltage Key Position
Unbuffered 3.3V

18
65MIV/65MIV2/65MIV-X/65MIV2-X
2-3 HDD/FDD INSTALLATION
• To install HDD (Hard Disk Drive), you may connect the cable’s blue
connector to the motherboard’s primary (IDE1) or secondary IDE
connector, and then connect the gray connector to your slave de-
vice and the black connector to your master device. If you install
two hard disks , you must configure the second drive to Slave mode
by setting its jumper accordingly. Please refer to your hard disk docu-
mentation for the jumper settings.
• To install FDD (Floppy Disk Drive), you may connect the single end
to the board , and connect two plugs on the other end to the floopy
drives.
Floppy Disk Drive Connector:
Orient the red markings on
the floppy ribbon cable to
Pin1.
Hard Disk Drive Connector:
Orient the red markings on
the IDE ribbon cable to Pin1.
13 13
JP4 JP5
13
JBAT1
13
JP9
JFAN2
JFAN1
WOL1
JCD1
JCD2
1 4
1 4
AGP 4X
PCI 1
PCI 2
PCI 3
DIMM1 DIMM2 DIMM3
FDD1
IDE2 IDE1
SOCKET 37
RT1
RT2
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97
Codec
Clock Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE PS/2 K/B
upper
lower
USB1 USB
upper
lower
VIA
VT86 5
VIA
VT82C
686A
COM2
DVC1
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC1 /PC133 SDRAM
1
1
1
J2 J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
++
--
+-
1 15 1 15

19
65MIV/65MIV2/65MIV-X/65MIV2-X
SW1 DIP1 ~ DIP4 SETTING
OFF
ON ON ON
ON
1 2 3 4 5 6
OFF
ON
3. x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
3.5x
OFF
ON ON ON
ON
1 2 3 4 5 6
OFF
ON
4. x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
4.5x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
5. x
OFF OFF OFF
ON
ON
1 2 3 4 5 6
OFF
ON
5.5x
OFF
ON ON ON
ON
1 2 3 4 5 6
OFF
ON
6. x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
6.5x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
7. x
OFF OFF OFF
ON
ON
1 2 3 4 5 6
OFF
ON
7.5x
OFF OFF
ON ON
ON
1 2 3 4 5 6
OFF
ON
8. x
2-4.1 CPU BUS RATIO SELECT
2-4.2 BUS CLOCK SELECT
• Over clocking is not recommended, your system may work unstable.
• Normally, the Bus Ratio (Frenquency Multiple) of your processor is locked
by processor’s Vendor, setting of the CPU Bus Ratio will have no effect.
• Bus Ratio exceed .0X, user can not change all values from DIP switch
the Bus ratio will be detected by BIOS automatically.
• The Bus Ratio Setting is available on unlocked processors only.
Auto Select 66/1 /133 MHz
(default)
SW1 DIP5 ~ DIP8 SETTING
ON
1234567
ON
OFF OFF
ON
66MHz
ON
1234567
ON
OFF OFF
ON
1 MHz
ON
1234567
OFF OFF OFF
ON
133MHz
ON
1234567
OFF OFF OFF OFF

20
65MIV/65MIV2/65MIV-X/65MIV2-X
Those connectors support processor/system/chassis cooling fan with +12V. Those
support three pin head connector. When connecting the wire to FAN connectors
user should give attention that the red wire is the positive and should be connected
to the +12V the black wire is Ground and should be connected to GND. If your
motherboard has Hardware Monitor chipset on-board you must use a specially
designed fan with speed sensor to take advantage of this function.
For fans with fan speed sensor every rotation of the fan will send out 2 pulses.
System Hardware Monitor will count and report the fan rotation speed.
NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN supports the FAN control. You can install PC Alert utility.
This will automatically control the CPU FAN speed according to the
actual CPU temperature.
CPU FAN
JFAN1/JFAN2: ONBOARD FAN (12V)
JFAN2
JFAN1
SYSTEM FAN
GND
+12V
SENSOR
2-5.1 ONBOARD FAN (JFAN1/JFAN2)
Redirect USB port 2 to USB 2
connector (default)
JP4/JP5: USB PORT SELECT (2)
1
3
1
3
JP4 JP5
Redirect USB port 2 to AGP
1
3
1
3
JP4 JP5
2-5.2 USB PORT SELECT (JP4/JP5)
• The figure below shows the location of the motherboard’s jumper blocks.
CAUTION
• Do not move the jumper with the power on. Always turn off the power and unplug
the power cord from the computer before changing the jumper. Otherwise, the
motherboard could be damaged.
2-5 JUMPER DEFINITIONS