ACTi Z39 User manual

Outdoor Mini Bullet
Hardware Manual
Z39, Z310, Z315
Ver. 2023/06/15

www.acti.com
Hardware Manual
2
Table of Contents
Precautions 3
Safety Instructions..................................................................................... 6
Introduction 7
List of Models............................................................................................ 7
Package Contents ...................................................................................... 8
Physical Description .................................................................................. 9
Mounting Options ....................................................................................10
Installation Procedures 11
Step 1: Prepare for Installation.................................................................11
Step 2: Route the Cables...........................................................................12
Step 3: Mount the Camera .......................................................................13
Step 4: Connect and Manage the Cables...................................................14
Using the Cable Gland.................................................................14
Using a Power Adapter (Optional)................................................17
Step 5: Connect to Network .....................................................................17
Step 6: Access the Camera Live View........................................................18
Step 7: Adjust the Viewing Angle and Orientation....................................18
Accessing the Camera 19
Configure the IP Addresses.......................................................................19
Using DHCP Server to Assign IP Addresses................................19
Using the Default Camera IP Address..........................................20
Access the Camera ...................................................................................22

www.acti.com
Hardware Manual
3
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to other
equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
Usage
•Use a power adapter or a PoE device that meets requirements. Otherwise, the device may
be damaged.
•Make sure the length of the power cable between the power adapter and the camera is not
too long, otherwise the voltage of the camera is lowered, causing the camera to work
abnormally. If it is required to lengthen the power cable, lengthen the cable between the
power adapter and the mains.
•Do not overbend the cables during the installation, otherwise, poor cable contact may cause
malfunction.
•When connecting to an external interface, use an existing connection terminal, and ensure
that the cable terminal (latch or clamp) is in good condition and properly fastened. Ensure
that the cable is not tense during mounting, with a proper margin reserved to avoid poor port
contact or loosening caused by shock or shake.

www.acti.com
Hardware Manual
4
•During transportation, special attention is required to protect the transparent dome cover
from friction, scratch and stain, etc. Do not remove the protective film from the cover until
mounting is finished. Remove the protective film before powering on the device.
•Contact professionals for maintenance information. Do not attempt to dismantle the device
by yourself. We shall not assume any responsibility for problems caused by unauthorized
repair or maintenance.
Maintenance
⚫If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a
rubber dust blowing ball.
⚫If there is grease or a dust stain on the front glass surface, clean the glass surface gently from
the center outward using anti-static gloves or an oil-free cloth. If the grease or the stain still
remains, use anti-static gloves or an oil-free cloth dipped with detergent and clean the glass
surface gently until it is clean.
⚫Do not use organic solvents (such as benzene and alcohol) to clean the transparent dome
cover.

www.acti.com
Hardware Manual
5
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
LVD / EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU and
EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical & Electronic
Equipment (WEEE) Directive and must be disposed of in a responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC.For proper recycling,return the battery to your supplier or to a
designated collection point.

www.acti.com
Hardware Manual
6
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Water and Moisture
Install other devices (such as PoE injector, alarm, etc.) that will be used with the camera in a dry
place protected from water.
Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
•Never look at the transmit laser while the power is on. Never look
directly at the fiber ports and the fiber cable ends when they are
powered on.
•Use of controls or adjustments to the performance or procedures
other than those specified herein may result in hazardous laser
emissions.

www.acti.com
Hardware Manual
7
Introduction
List of Models
This hardware manual contains the following models:
Z39
4MP Mini Bullet with D/N, Adaptive IR, Superior WDR, SLLS,
Fixed Lens
Z310
8MP Mini Bullet with D/N, Adaptive IR, Superior WDR, SLLS,
Fixed Lens
Z315
5MP Mini Bullet with D/N, Adaptive IR, Superior WDR, SLLS,
Fixed Lens

www.acti.com
Hardware Manual
8
Package Contents
Check if the camera package comes with the following items:
Camera
Cable Gland
with Rubber and Washer
Mounting Screw Kit
Drill Template
Wrench
Drill Template
Quick Guide &
Warranty Card
IMPORTANT: When the camera is taken out from the box, the lens cover is covered by a thin film.
DO NOT remove this film. It is used to protect the lens cover from scratches or fingerprint marks
which may happen during installation. Remove this film only after the camera is securely installed
and all connections are complete.
Drill Template
Warranty Card

www.acti.com
Hardware Manual
9
Physical Description
Item
Description
1
DC 12V Power
Input
In case the camera is connected to a non-PoE (Power over
Ethernet) switch, use this connector to connect the camera to an
external power adapter (not included). See Using a Power
Adapter (Optional) on page 17 for more information.
CAUTION: If the power cable will not be used, make sure to
insert the plug to cover the connector.
2
Ethernet Port
Connects to a network using an Ethernet cable with RJ-45
connector.
3
Built-in
Microphone
Receives audio input.
4
Memory Card Slot
Insert a memory card (not included) into the slot for local
recording purposes.
5

www.acti.com
Hardware Manual
10
Mounting Options
Select the most suitable solution for your installation environment. The camera can be
mounted by either of the following methods:
Mount Types
Accessories
Surface Mount
Suitable when mounting the camera directly on walls or ceilings without
additional mounting accessories. See Installation Procedures on page
11 for more information.
An additional junction box can be used with the camera for cable
management. Contact sales to purchase.
Pole mount
Suitable when installing the camera on a pole. The Pole mount (optional
accessory set) is required for this type of installation.
NOTE:
•For more information about the mounting solutions and accessories, please check the
Mounting Accessory Selector in our website (http://www.acti.com/mountingselector).
•The above mounting accessories are not included in the package. Contact your sales
agents to purchase.

www.acti.com
Hardware Manual
11
Installation Procedures
This section describes procedures in mounting the camera on a flat surface.
NOTE: The camera images on this documentation are for reference only and may be different
from the actual camera.
Step 1: Prepare for Installation
1. Before installing the camera, prepare other accessories required for installation. In case of
using a memory card for local recording, open the bottom cover of the camera and insert the
memory card.
NOTE: Do not hot plug the memory card after it has been inserted and the power turned on,
otherwise, the camera or the card might be damaged.
2. Determine whether the cable will go through a hole on the surface or be routed along the
surface. Note also the direction to which the cable will be routed to attach the bundled drill
template on the surface according to the direction of the cable.
Micro SD card slot

www.acti.com
Hardware Manual
12
3. Drill the screw holes. Depending on the material of the surface where the camera will be
installed, it may be necessary to drill the three (3) screw holes and use the supplied screw
tox.
Step 2: Route the Cables
Determine whether the cable will pass through a hole on the surface or be routed along the
surface:
If the cable will pass through a hole on the surface:
1. Drill the hole for the cable on the surface.
2. Route the cable from the network side and connect it to the Ethernet port of the camera.
NOTE: If the camera will be installed outdoors or in places wherein environmental factors
change drastically, make sure to waterproof the cable connection; see Step 4: Connect and
Manage the Cable on page 14 for instructions.
3. Push the cable through the hole on the surface.
4. Skip to Step 3: Mount the Camera on page 13.
If the cable will be routed along the surface, route the cable through the gap on the side of
the camera bracket.

www.acti.com
Hardware Manual
13
Step 3: Mount the Camera
1. Loosen the head screw to tilt the camera, as needed, before mounting the camera to the
wall surface.
2. Mount the camera to the surface using the three (e) bundled screws.
3. Adjust the camera tilt angle, then fasten the head screw to fix the camera angle position.
Locknut
2
3
1

www.acti.com
Hardware Manual
14
Step 4: Connect and Manage the Cables
The camera and the pre-installed network cable, “pigtail”, are resistant to salt, water, weak acid,
alcohol, oil, grease and other common solvents. If the camera will be installed indoors, simply
connect the network side cable to the camera Ethernet port.
However, if the camera will be installed outdoors, ensure that the cable connections are
protected from different environmental factors. Use the bundled cable gland to protect the
Ethernet connection and use a waterproof tape to protect other cable connections. See Using a
Power Adapter (Optional) on page 17 for more information.
DISCLAIMER: ACTi will not be responsible for camera damage caused by water entering the
cable connections.
Using the Cable Gland
This section describes how to waterproof the cable-out or “pigtail” of the camera using the
bundled cable gland. Before connection, prepare an exterior-grade Ethernet cable with RJ-45
connector.
Perform the following to waterproof the “pigtail” using the cable gland:
1. Attach the washer to the Ethernet connector of the camera.
2. Detach the clamping nut and sealing insert from the gland body:
Gland Body
Clamping Nut
Sealing Insert

www.acti.com
Hardware Manual
15
3. Insert the clamping nut into the Ethernet cable.
4. Insert the sealing insert through the Ethernet cable.
5. Insert the cable through the gland body.
6. Push the sealing insert into the gland body.

www.acti.com
Hardware Manual
16
7. Connect the RJ-45 connector to the camera connector.
8. Attach the gland body to the camera connector.
9. Attach the clamping nut to the gland body to complete the cable solution.
NOTE: Make sure the clamping nut is tightly attached to the cable gland body and the sealing
insert is squeezed tightly.

www.acti.com
Hardware Manual
17
Using a Power Adapter (Optional)
The camera can be powered by a Power over Ethernet (PoE) switch that is IEEE802.3af
compliant. In case of using a non-PoE switch or your PoE switch has limited power supply, you
can purchase a power adapter and directly connect the camera to a power outlet.
After connecting the power adapter, wrap the cable connection with waterproof take to ensure it
is protected.
NOTE: The power adapter is not bundled in the package.
CAUTION: The cable connector must not be exposed and must be kept away from water. If the
cable will not be used, make sure to insert the plug to cover the cable interface. Then put the
cable inside a waterproof junction box or completely wrap with waterproof tape.
Step 5: Connect to Network
Connect the other end of the network cable to a switch or injector. Then, connect the switch or
injector to a network or PC and a power source. See Power-over-Ethernet (PoE) example
connection diagram below.
Network
AC Power
Source
PoE Injector /
PoE Switch
Power Cable
Ethernet Cable
Ethernet Cable
(Data + Power)
Ethernet Cable
(Data)
Camera
DC interface
Plug

www.acti.com
Hardware Manual
18
Step 6: Access the Camera Live View
See Accessing the Camera on page 19 for more information on how to access the Live View of
the camera.
Step 7: Adjust the Viewing Angle and Orientation
2
3
1

www.acti.com
Hardware Manual
19
Accessing the Camera
Configure the IP Addresses
In order to be able to communicate with the camera from your PC, both the camera and the PC
have to be within the same network segment. In most cases, it means that they both should have
very similar IP addresses, where only the last number of the IP address is different from each
other. There are 2 different approaches to IP Address management in Local Area Networks – by
DHCP Server or Manually.
Using DHCP Server to Assign IP Addresses
If you have connected the computer and the camera into the network that has a DHCP server
running, then you do not need to configure the IP addresses at all – both the camera and the PC
would request a unique IP address from DHCP server automatically. In such case, the camera will
immediately be ready for the access from the PC. The user, however, might not know the IP
address of the camera yet. It is necessary to know the IP address of the camera in other to be
able to access it by using a Web browser.
If you work with our cameras regularly, there is a better way to discover the cameras in the
network – by using IP Utility. The IP Utility is a light software tool that can not only discover the
cameras, but also list lots of valuable information, such as IP and MAC addresses, serial numbers,
firmware versions, etc, and allows quick configuration of multiple devices at the same time.
The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility
With just one click, you can launch the IP Utility and there will be an instant report as follows:
You can quickly see the camera model in the list. Double-click on the IP address to automatically
launch the default browser of the PC with the IP address of the target camera filled in the address
bar of the browser already.

www.acti.com
Hardware Manual
20
Using the Default Camera IP Address
If there is no DHCP server in the given network, the user may have to assign the IP addresses
to both PC and camera manually to make sure they are in the same network segment.
When the camera is plugged into network and it does not detect any DHCP services, it will
automatically assign itself a default IP:
192.168.0.100
Whereas the default port number would be 80. In order to access that camera, the IP address of
the PC has to be configured to match the network segment of the camera.
Manually adjust the IP address of the PC:
In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99
and set Subnet Mask to 255.255.255.0 by using the steps below:
1
2