ActionTec MegaPlug AV HPE200AV User manual

200 Mbps
MegaPlug
Ethernet
Adapter
Model #: HPE200AV
User Manual
Ver 1.0
Solutions for the Digital Life™

i
Table of Contents
1 Introduction 1
Package Contents 1
Features 2
System Requirements 2
Getting to Know the Ethernet Adapter 3
Technical Support 4
2 Connecting the MegaPlug Adapter 5
Connecting the Adapters 5
Installing the Configuration Utility 6
3 Using the Configuration Utility 9
Encryption Key 9
About 10
4 Troubleshooting 11
Troubleshooting 11
Frequently Asked Questions 12
5 Setting Up Static IP Address 15
Windows Vista 15
Windows XP 20
Windows 2000 23
Windows Me 27
Windows 98 SE 30
6 Setting Up File and Printer Sharing 33
File Sharing 33
Printer Sharing 41
A Specifications 43
General 43
LED Indicators 44
Environmental 44
B Glossary 45
Notices 47
Regulatory Compliance Notices 47
Modifications 47
Miscellaneous Legal Notices 48
Limited Warranty 49

ii
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
ii
This page left intentionally blank.

1
Introduction
Thank you for purchasing the Actiontec MegaPlug AV 200 Mpbs Ethernet Adapter.
The MegaPlug Ethernet Adapter is one of the easiest ways to enjoy home or small
business networking. It operates on the MegaPlug Powerline Specification AV stan-
dard, providing fast data transfer speeds over home AC wiring. Since home power
lines are the most common medium in households, with multiple outlets in every
room, the MegaPlug Ethernet Adapter allows multiple desktop and laptop comput-
ers to be networked easily, enabling them to share an Internet connection, printers,
files, and games, without any additional wiring. If you want to take your computer
networking to the next level, the Actiontec MegaPlug Ethernet Adapter is sure to be
one of the keys to your success.
Package Contents
Make sure the following items came in the kit:
s Two Actiontec MegaPlug AV 200 Mbps Ethernet Adapter
s Two Ethernet cables
s Installation CD (includes this manual)
s Quick Start Guide
1

2
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
3
Chapter 1 Introduction
Features
s HomePlug Turbo compliant
s 200 Mbps data rate (maximum)
s 128-bit AES encryption
s Two-pronged US power plug (fits ungrounded power outlets)
s Power and Link indicators
System Requirements
s At least one available power outlet
s Standard home power wiring
s Computer with the following:
· CD-ROM drive
· IBM compatible running at 200 MHz or better
· Windows 98SE, Me, 2000, or XP installed
· 64 MB of RAM
· Ethernet network adapter
· TCP/IP installed

2
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
3
Chapter 1 Introduction
Getting to Know the Ethernet Adapter
This section contains a quick description of the Adapter’s external features.
Front Panel
The Adapter’s front panel features 3 lights (LEDs):
Power Light
The Power light glows green when sychronized with another device. If the Power
light is off, it can still be powered up.
Link Light
The Link light glows green when an Ethernet connection is detected.
Ethernet Light
The Ethernet light flickers when data is being transferred across the Adapter.
Bottom Panel
The Adapter’s bottom panel contains one Ethernet port:
Ethernet Port
The Ethernet port is used to connect the Adapter to a computer or gateway/
router via Ethernet cable.
Information Sticker
The information sticker (located beneath the electrical prongs) displays the MAC
(Media Access Control) address, device ID, serial number and other information
about the Adapter.

4
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
Technical Support
Actiontec Electronics prides itself on making durable, high-quality, high-perfor-
mance products. If you need assistance, the Actiontec Technical Support Department
is available all day every day to provide professional support.
Actiontec Electronics, Inc.
760 N. Mary Avenue
Sunnyvale, CA 94085
Technical Support
Phone: (USA) 1-888-436-0657
E-mail: http://support.actiontec.com/email_support/support_form.php
Internet: www.actiontec.com/support

5
Connecting the
MegaPlug Adapter
To connect the Adapter, it must be connected to a computer, plugged into a stan-
dard wall outlet, and the Configuration Utility loaded on the computer.
Connecting the Adapters
To use the Adapters properly, two Adapters should be plugged into electrical out-
lets, and devices (computers, printers, etc.) connected to them.
Connecting an Adapter to a Computer
1. Get an Adapter and one Ethernet cable.
2. Insert one end of the Ethernet cable into the Ethernet port of the Adapter.
3. Plug the Adapter into a wall outlet.
☞
Note: Do not plug the Adapter into a UPS or power strip with
surge protection. The Adapter’s network signal may not pass
through these devices.
4. Insert the other end of the Ethernet cable into an Ethernet port on the back of
a computer.
Connecting an Adapter to a Router/Gateway
1. Get an Adapter and one Ethernet cable.
2. Insert one end of the Ethernet cable into the Ethernet port of the Adapter.
3. Plug the Adapter into a wall outlet.
☞
Note: Do not plug the Adapter into a UPS or power strip with
surge protection. The Adapter’s network signal may not pass
through these devices.
4. Insert the other end of the Ethernet cable into an Ethernet port on a router/
gateway connected to a computer.
2

6
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
7
Chapter 2 Connecting the MegaPlug Adapters
5. Insert the other end of the Ethernet cable into an Ethernet port on a router/
gateway connected to a computer.
Follow the instructions in the next section, “Installing the Configuration Utility.”
Installing the Configuration Utility
After connecting the Adapters, install the Configuration Utility:
1. Insert the Installation CD in the CD-ROM drive of the computer connected
to an Adapter.
2. When the “Welcome” screen appears, click Next.
3. When the “Choose Destination Screen” appears, click Next.

6
Actiontec MegaPlug AV 200 Mbps Ethernet Adapter User Manual
7
Chapter 2 Connecting the MegaPlug Adapters
4. When this window appears, click Finish.
5. Repeat for other computers connected to an Adapter.
☞ Note: If using a computer running Windows Vista, you may
have to click through a “User Account Control” window to
install the program.
The MegaPlug Adapters are now connected and ready to use, and the
Configuration Utility is loaded on the computers. Go to chapter 3, “Using the
Configuration Utility” for information about changing the default configuration
settings of the Adapter.