ActiveAid 922 User manual
This warranty is extended only to the original purchaser/customer (or supplier non consumer who does not buy
or resell). ActiveAid, LLC, warrants the 922 against defects in materials and workmanship as listed below.
• StainlessSteelFrames–3yearwarranty
• Brakemechanisms,lockingmechanisms,wheelsandcasters–1yearwarranty
• Othermetalandstructuralpartsnotofstainlesssteel--1yearwarranty
• Upholsteredcomponents,plasticpads,rubberparts,paintedsurfaces,bearingsandotherpartsnot
specicallyidentiedabove–6monthswarranty
The warranty period commences on the original ship date from ActiveAid. Any product proven to ActiveAid’s
satisfaction to be defective and within warranty period shall be repaired or replaced at ActiveAid’s option.
ACTIVEAID’sSOLEOBLIGATIONANDYOUREXCLUSIVEREMEDYUNDERTHISWARRANTYSHALLBE
LIMITEDTOSUCHREPAIRAND/ORREPLACEMENT.Thiswarrantydoesnotincludeanylaborcharges
incurredinreplacementpartsinstallation.Forwarrantyservice,pleasecontacttheauthorizedsupplierfrom
whom you purchased your ActiveAid product. In the event you do not receive satisfactory warranty service,
please contact ActiveAid at the address below. Do not return products to our factory without prior
authorization.
LIMITATIONSANDEXCLUSIONS:Theforegoingwarrantyshallnotapplytoserialnumberedproductsifthe
serialnumberhasbeenremovedordefaced.Productssubjecttonegligence,abuse,misuse,improper
maintenance, improper storage, or damages beyond ActiveAid’s control are not covered by this warranty, and
thatevaluationwillbesolelydeterminedbyActiveAid.ProductsmodiedwithoutActiveAid’sexpresswritten
consent(includingbutnotlimitedto,modicationthroughtheuseofunauthorizedpartsorattachments)arenot
covered by this warranty. The warranty shall not apply to problems arising from normal wear or failure to follow
instructions. The warranty will be void if parts not manufactured by ActiveAid or parts not complying with
originalequipmentspecicationsareaddedtoanActiveAidproduct.
THEFOREGOINGWARRANTYISEXCLUSIVEANDINLIEUOFALLOTHEREXPRESSWARRANTIES.
ACTIVEAIDSHALLNOTBELIABLEFORANYCONSEQUENTIALORINCIDENTALDAMAGESWHATSOEVER.
ActiveAid maintains a policy of continual product improvement and reserves the right to change features,
specications,andpriceswithoutpriornotication.CheckwithActiveAidforlatestinformation.
ActiveAid, LLC.
101ActiveaidRoad•RedwoodFallsMN56283USA
activeaid.com
OWNER’S MANUAL
922
ActiveAid products should only be used under the guidance of a physician. ActiveAid maintains a policy of continual product improvement and reserves the
right to change features, specications, and prices without prior notication. Check with ActiveAid for latest information. FORM 922MAN 121819 REV A
Copyright © 2019 ActiveAid, llc. All rights reserved. Printed in the U.S.A.
LimitedWarranty
12
Please ensure the Owner’s Manual stays with the unit at all times.
10
DATE OF MANUFACTURE
SEE INSTRUCTIONS FOR USE
MANUFACTURER
SYMBOL LEGEND
!
!
CAUTION/ATTENTION
SERIAL NUMBER
SN
Please be environmentally responsible and
recycle this product through your recycling
facility at its end of life.
Afin de préserver l’environnement, veuillez
confier ce produit à votre centre de recyclage
à la fin de sa durée de vie.
Usage(cont.)
Casters
Lockingcasters:Tolockcasters(option),pushdownonthefrontofthecasterbrakelever.Toreleasecaster
brake, push down on the rear of the caster brake.
Removing Casters:Loosenthenremovetheself-lockingnutandmachinescrewthatareinthechairframe
wherethecasterswillbeinserted.Insertcastersothatitisushwiththeframe.Re-insertthescrewthroughthe
holes in the chair frame and caster stem. Note: Screw head should be to the outside of the frame and the nut to
the inside.HandstartthenutontotheendofthescrewUseawrenchandhexkeytotightenthecastersinto
place.Repeatforsecondcaster.
Wheels
Quick Release Axle
Depressbuttonontheaxleendtorecesstheballlockingpinsandstarttheboltthruthewheel.Placewasher
on bolt end to inside of wheel. Continue depressing the button to insert the bolt into the wheel mount.
Note: The ball locking pins will secure the axle in place when the button is released.
Wheel Locks
To engage the wheel lock, push forward on the lever, to unlock pull back on the lever.
Note: If the wheel moves while wheel lock is engaged, the assembly needs to be moved slightly closer to
the wheel.
Belts
Hook and Loop Fasteners
Pullthebeltstripsaparttoseparatethem.Adjustthestripstotheproperposition.Pressthebeltstripstogether
to connect them.
Snap Fit Buckle
To unbuckle, depress the two spring arms on the male end and pull/slide to separate it from the female receiver.
To buckle, insert the male end into the female receiver until the spring arms secure. Listen for clicking sound to
indicateitissecure.Pullstrapthrumaleportionofbuckletotighten.
Abductor/Deector
Slidedeectorintothefrontopeningoftheseat.
Swing Away Adjustable Laterals
To swing the lateral back out of the way, depress the button, pull lateral back around behind the back. To make
widthadjustments,loosenscrews,slidelateralleftorrightinbrackettodesiredposition,tightenscrew.
Check all fasteners (snap buttons, screws, nuts, bolts, clips, pull pins, handles, etc.) for tightness and make sure
they are secure.
Introduction ..................................1
Safety Precautions ............................ 2
Assembly ................................... 3
Usage ...................................... 9
Maintenance................................ 11
Limited Warranty.............................12
Date Purchased:___________________ Serial#:_______________________________
Model #:__________________________ Supplier: ____________________________
Table of Contents Usage
Seat
Removebyliftingonecorneratatimeorliftoonesideonlyandpivottheseatupfromtheoppositeside.
Folding Frame
Unfold
Movethesideframesapart,PullforwardontheFoldFramePullPinuntilthefoldframelocksintoplace.
Fold
PushinontheFoldFramePullPinandmovethetwosideframestogetheruntiltheframeiscompletely
collapsed.
Note: The pan hanger, commode pan and seat may be removed prior to folding. The back and ip back style arms
must also be removed prior to folding and placed into carry case.
Disassembly for Storage or Transportation.
FollowingtheUsageinstructions,removetheip-upstylearms(heightadjustable
arms may not need to be removed from back assembly), remove the back
assembly, remove the rear wheels, remove the seat, remove the pan/hanger.
Foldtheframeandsecureitwiththebuckle.Placecomponentsinto
storage/travel bag.
FollowAssemblyinstructionstoreassembletheunit.
Back
Loosenthenremovetheself-lockingnutandscrewthataresecuringthebackassemblytotheframe.Pullupon
thebackassembly.Re-insertthescrewthroughtheholesinthechairframe.Handstartthenutontotheendof
the screw.
Leg Rests
Adjusttheheightofthefootplatebydepressingsnapbuttonandslidingfootplatemountupordowntoobtain
correctheight.Removelegrestassemblybyliftinguponthegoosenecktoremoveitfromthereceiverofthe
front support.
Elevating Leg Rest
Adjusttheheightofthelegrestbydepressingsnapbuttonandslidingfootplatemountupordowntoobtain
correctheight.Adjusttheangleofthelegrestupwardbylifting,lowerbydepressingthetab.
Arm Rests
Height-Adjustable Arm Rests
To raise the arm, push up on the armlock cap and pivot back the entire armrest. To lower the arm, pull down on
the front of the armrest until the arm latch locks onto the securing stud under the arm pivot.
Flip-Up Arm Rests
To raise the arm up, pivot the arm lock lever away from the armrest and armrest lock. Lift up on the armrest.
Removebydepressingthesnapbuttonandslidingitoutofthearmrestpivot.
Serialnumberislocatedonthe
frame behind the wheel.
9
Buckle
2 7
SafetyPrecautions
•Pleasereadandunderstandallsafetyprecautionsanduserinstructionspriortouse.CallActiveAidat
1-800-533-5330or507-644-2951withquestionsorconcerns.
•TheShower/Commode chair is designed to accommodate most individuals up to 350 lbs. (158kg).
•Theexpectedservicelifeofa922productis3yearsundernormaluseconditions.Note: this may vary based on
frequency of use.
•ActiveAidproductsarespecicallydesignedtobeusedwithActiveAidaccessoriesandoptions.Unless
otherwise noted, accessories and options from other manufacturers have not been tested by ActiveAid and are
not recommended for use with ActiveAid products.
•Productmodicationsmadewithoutexpresswrittenconsent(includingbutnotlimitedto,modicationthrough
theuseofunauthorizedpartsorattachments)arenotrecommendedandwillvoidtheproductwarranty.
•Thisequipmentisdesignedtoaccommodatearangeofusers;therefore,theunithasvariousadjustmentslots
andholes.Avoidplacingngersorotherbodypartsinanyoftheseareas.
•Pleasedisposeofpackagingmaterialsproperly.Keepplasticbagsawayfromchildren.
•ActiveAidshower/commodechairsaredesignedforindooruseonly.
•Donotsubmergetheshower/commodechair.
•Extrememovementslaterallyorfronttobackmaycausetheunittotip.Thesemovementswillcauseachange
to the normal center of gravity of the chair.
•Whentransferringorre-positioninginthechair,ensurecastersareproperlyaligned(frontcastersinforward
position, rear casters positioned to the rear) and wheel locks/caster locks are locked (as applicable to the
congurationoftheselectedproduct).
•Donotusefootplatesinthetransferprocessorwhenshiftingyourweight.
•Wheellocks/casterlocksareintendedtokeeptheshower/commodechairstationaryduringtransferoruse.
They are not intended to be used as brakes to slow and stop a moving shower/commode chair.
•Donotremovetheanti-tiplevers,theyproviderearwardstability.
•Donotexceedtherecommendedtirepressure(onthesidewallofthetire)forPneumaticWheels.
•Caution: Check all fasteners before operating.
•Caution: It is necessary to periodically check all fasteners (snap buttons, screws, nuts, bolts, clips, pull pins,
handles, etc.) to ensure they are secure.
13. Ifswing-awayadjustablelateralswereordered,
remove the bolts from the lateral assembly.
14. Placelateralclampandlateralassemblyontotheback
frameabovethearmrestassembly.Placeclampbracket
into place and hand start each bolt.
15. Tighten bolts securely.
Repeatstepsforotherside,ifordered.
Introduction
CONGRATULATIONS!Youhaveselectedoneofourmanynemobilityproducts.YourShower/CommodeChair
has been carefully designed and fabricated focusing on customer needs.
Shower/Commode Chair Description
ActiveAid shower and commode products are intended for individuals who are able to transfer independently or
with assistance from a caregiver. They are a useful tool for rehabilitation or home use. ActiveAid shower and
commodeproductscanbeindividuallyconguredtomeetthespecicneedsofanindividual.
Indications for Use
The Shower/Commode Chair is indicated for most individuals weighing up to 350 lbs. (158kg).
Intended Use
ActiveAid shower and commode products are intended to assist disabled individuals in performing activities of
daily living (toileting and bathing).
This device is designed and intended for shower/commode use in accessibility compliant environments.
Accessibilitycompliantenvironmentsgenerallyoutlinethatooringsurfacesaretobestable,rmandslip
resistant.Ifgroundandoorsurfacesareencounteredthatarenotwithintheappropriateaccessiblestandards,
the area in question should be brought within the code for disability accessibility before using the device.
This manual is an integral part of your Shower/Commode Chair product and should be read completely and
thoroughly by anyone that will be operating the unit. This will ensure the product is assembled properly and
usedinthemostbenecialmanner.
The ActiveAid 922 should only be used under the guidance of a physician or therapist. Consult your physician or
therapist for proper transfer techniques.
Shouldanyproblemarisethatyoucannotsolvebyreadingthismanual,pleasecontactyourlocalsupplierorcall
ActiveAid,LLCat1-800-533-5330or1-507-644-2951.
ItisnecessarytoinspectyourShower/Commodechairatleastweeklytoensureitisinsafeoperatingcondition.
Adjustmentsthatarelistedintheproductowner’smanualcanbemadebytheoperatorbyfollowingthe
instructionsforuse.Afteranadjustmentismade,inspecttheunittoensureallhardwareandadjustable
componentsareproperlysecuredpertheinstructionsforuse.Replacementofwornparts,majoradjustments,
oranyotherimportantcorrectionsshouldbehandledbyanauthorizedsupplier.OnlyActiveAid,LLCapproved
replacement parts should be used to ensure safety and performance.
THANKYOUFORBUYINGANACTIVEAIDPRODUCT!
16. If the leg rests were ordered, insert the ends (with the
pin)intothereceiverofthefrontsupport.Pushdownto
secure the leg rest into the front support.
Repeatforsecondlegrest,ifordered.
17. Insert pan hanger under the seat.
18. Placepanontopanhanger.
PanHangerHookPlacement
8 1
6 3
Assembly
1. Removeallpartsfromtheshippingcontainer(s).
Removeallpackingmaterialfromtheparts.Recycle
shipping and packing materials in accordance with the
recycling codes of your location.
MovethesideframesapartandpullforwardontheFold
FramePullPinuntilthefoldframelocksintoplace
2. Placethefrontseatsnapbracketsontothefrontseat
support tubes and than place rear seat snap brackets
onto the rear seat support tubes.
Makesurethattheseatissquare,andall4cornersare
snapped into place before sitting on chair.
3. Loosenthenremovetheself-lockingnutandscrewthat
are in the chair frame where the back assembly will be
attached and set aside.
Tools required for setup: 3/4" wrench, 3/4" socket wrench, 7/16" wrench,
#10 metric wrench, 5/32" hex key
FoldFramePullPin
10. Iftheheight-adjustablearmrestswereordered,
remove the two hex bolts in the clamp of the armrest
clamp assembly.
11. Placearmrestandarmrestclampontothebackframe
as shown. Insert the hex bolt and hand start two bolts into
the clamp.
12. Placearmrestandarmrestclamp81/4"fromthetop
of the frame and tighten bolts securely.
Repeatsteps6-12fortheotherarmrest.
FrontSnapBracket RearSnapBracket
4 5
4. Insert the back into the frame.
5. Usingtheself-lockingnutandscrewthatwereremoved
instep3,insertthemandtightensecurelyusingawrench
and hex key to tighten the back into place.
6.Iftheip-uparmrestswereordered,depressthespring
button and insert into the bracket on the back frame.
5.
7. Makesurethepushpinissetasshown.
8. Lower arm down and insert the front of the arm into the
receiver on the front of the seat frame and push down into
place.
9. Pivotthearmlocklevertolockarmrestintoplace.
4 5
4. Insert the back into the frame.
5. Usingtheself-lockingnutandscrewthatwereremoved
instep3,insertthemandtightensecurelyusingawrench
and hex key to tighten the back into place.
6.Iftheip-uparmrestswereordered,depressthespring
button and insert into the bracket on the back frame.
5.
7. Makesurethepushpinissetasshown.
8. Lower arm down and insert the front of the arm into the
receiver on the front of the seat frame and push down into
place.
9. Pivotthearmlocklevertolockarmrestintoplace.
6 3
Assembly
1. Removeallpartsfromtheshippingcontainer(s).
Removeallpackingmaterialfromtheparts.Recycle
shipping and packing materials in accordance with the
recycling codes of your location.
MovethesideframesapartandpullforwardontheFold
FramePullPinuntilthefoldframelocksintoplace
2. Placethefrontseatsnapbracketsontothefrontseat
support tubes and than place rear seat snap brackets
onto the rear seat support tubes.
Makesurethattheseatissquare,andall4cornersare
snapped into place before sitting on chair.
3. Loosenthenremovetheself-lockingnutandscrewthat
are in the chair frame where the back assembly will be
attached and set aside.
Tools required for setup: 3/4" wrench, 3/4" socket wrench, 7/16" wrench,
#10 metric wrench, 5/32" hex key
FoldFramePullPin
10. Iftheheight-adjustablearmrestswereordered,
remove the two hex bolts in the clamp of the armrest
clamp assembly.
11. Placearmrestandarmrestclampontothebackframe
as shown. Insert the hex bolt and hand start two bolts into
the clamp.
12. Placearmrestandarmrestclamp81/4"fromthetop
of the frame and tighten bolts securely.
Repeatsteps6-12fortheotherarmrest.
FrontSnapBracket RearSnapBracket
2 7
SafetyPrecautions
•Pleasereadandunderstandallsafetyprecautionsanduserinstructionspriortouse.CallActiveAidat
1-800-533-5330or507-644-2951withquestionsorconcerns.
•TheShower/Commode chair is designed to accommodate most individuals up to 350 lbs. (158kg).
•Theexpectedservicelifeofa922productis3yearsundernormaluseconditions.Note: this may vary based on
frequency of use.
•ActiveAidproductsarespecicallydesignedtobeusedwithActiveAidaccessoriesandoptions.Unless
otherwise noted, accessories and options from other manufacturers have not been tested by ActiveAid and are
not recommended for use with ActiveAid products.
•Productmodicationsmadewithoutexpresswrittenconsent(includingbutnotlimitedto,modicationthrough
theuseofunauthorizedpartsorattachments)arenotrecommendedandwillvoidtheproductwarranty.
•Thisequipmentisdesignedtoaccommodatearangeofusers;therefore,theunithasvariousadjustmentslots
andholes.Avoidplacingngersorotherbodypartsinanyoftheseareas.
•Pleasedisposeofpackagingmaterialsproperly.Keepplasticbagsawayfromchildren.
•ActiveAidshower/commodechairsaredesignedforindooruseonly.
•Donotsubmergetheshower/commodechair.
•Extrememovementslaterallyorfronttobackmaycausetheunittotip.Thesemovementswillcauseachange
to the normal center of gravity of the chair.
•Whentransferringorre-positioninginthechair,ensurecastersareproperlyaligned(frontcastersinforward
position, rear casters positioned to the rear) and wheel locks/caster locks are locked (as applicable to the
congurationoftheselectedproduct).
•Donotusefootplatesinthetransferprocessorwhenshiftingyourweight.
•Wheellocks/casterlocksareintendedtokeeptheshower/commodechairstationaryduringtransferoruse.
They are not intended to be used as brakes to slow and stop a moving shower/commode chair.
•Donotremovetheanti-tiplevers,theyproviderearwardstability.
•Donotexceedtherecommendedtirepressure(onthesidewallofthetire)forPneumaticWheels.
•Caution: Check all fasteners before operating.
•Caution: It is necessary to periodically check all fasteners (snap buttons, screws, nuts, bolts, clips, pull pins,
handles, etc.) to ensure they are secure.
13. Ifswing-awayadjustablelateralswereordered,
remove the bolts from the lateral assembly.
14. Placelateralclampandlateralassemblyontotheback
frameabovethearmrestassembly.Placeclampbracket
into place and hand start each bolt.
15. Tighten bolts securely.
Repeatstepsforotherside,ifordered.
Introduction
CONGRATULATIONS!Youhaveselectedoneofourmanynemobilityproducts.YourShower/CommodeChair
has been carefully designed and fabricated focusing on customer needs.
Shower/Commode Chair Description
ActiveAid shower and commode products are intended for individuals who are able to transfer independently or
with assistance from a caregiver. They are a useful tool for rehabilitation or home use. ActiveAid shower and
commodeproductscanbeindividuallyconguredtomeetthespecicneedsofanindividual.
Indications for Use
The Shower/Commode Chair is indicated for most individuals weighing up to 350 lbs. (158kg).
Intended Use
ActiveAid shower and commode products are intended to assist disabled individuals in performing activities of
daily living (toileting and bathing).
This device is designed and intended for shower/commode use in accessibility compliant environments.
Accessibilitycompliantenvironmentsgenerallyoutlinethatooringsurfacesaretobestable,rmandslip
resistant.Ifgroundandoorsurfacesareencounteredthatarenotwithintheappropriateaccessiblestandards,
the area in question should be brought within the code for disability accessibility before using the device.
This manual is an integral part of your Shower/Commode Chair product and should be read completely and
thoroughly by anyone that will be operating the unit. This will ensure the product is assembled properly and
usedinthemostbenecialmanner.
The ActiveAid 922 should only be used under the guidance of a physician or therapist. Consult your physician or
therapist for proper transfer techniques.
Shouldanyproblemarisethatyoucannotsolvebyreadingthismanual,pleasecontactyourlocalsupplierorcall
ActiveAid,LLCat1-800-533-5330or1-507-644-2951.
ItisnecessarytoinspectyourShower/Commodechairatleastweeklytoensureitisinsafeoperatingcondition.
Adjustmentsthatarelistedintheproductowner’smanualcanbemadebytheoperatorbyfollowingthe
instructionsforuse.Afteranadjustmentismade,inspecttheunittoensureallhardwareandadjustable
componentsareproperlysecuredpertheinstructionsforuse.Replacementofwornparts,majoradjustments,
oranyotherimportantcorrectionsshouldbehandledbyanauthorizedsupplier.OnlyActiveAid,LLCapproved
replacement parts should be used to ensure safety and performance.
THANKYOUFORBUYINGANACTIVEAIDPRODUCT!
16. If the leg rests were ordered, insert the ends (with the
pin)intothereceiverofthefrontsupport.Pushdownto
secure the leg rest into the front support.
Repeatforsecondlegrest,ifordered.
17. Insert pan hanger under the seat.
18. Placepanontopanhanger.
PanHangerHookPlacement
8 1
Introduction ..................................1
Safety Precautions ............................ 2
Assembly ................................... 3
Usage ...................................... 9
Maintenance................................ 11
Limited Warranty.............................12
Date Purchased:___________________ Serial#:_______________________________
Model #:__________________________ Supplier: ____________________________
Table of Contents Usage
Seat
Removebyliftingonecorneratatimeorliftoonesideonlyandpivottheseatupfromtheoppositeside.
Folding Frame
Unfold
Movethesideframesapart,PullforwardontheFoldFramePullPinuntilthefoldframelocksintoplace.
Fold
PushinontheFoldFramePullPinandmovethetwosideframestogetheruntiltheframeiscompletely
collapsed.
Note: The pan hanger, commode pan and seat may be removed prior to folding. The back and ip back style arms
must also be removed prior to folding and placed into carry case.
Disassembly for Storage or Transportation.
FollowingtheUsageinstructions,removetheip-upstylearms(heightadjustable
arms may not need to be removed from back assembly), remove the back
assembly, remove the rear wheels, remove the seat, remove the pan/hanger.
Foldtheframeandsecureitwiththebuckle.Placecomponentsinto
storage/travel bag.
FollowAssemblyinstructionstoreassembletheunit.
Back
Loosenthenremovetheself-lockingnutandscrewthataresecuringthebackassemblytotheframe.Pullupon
thebackassembly.Re-insertthescrewthroughtheholesinthechairframe.Handstartthenutontotheendof
the screw.
Leg Rests
Adjusttheheightofthefootplatebydepressingsnapbuttonandslidingfootplatemountupordowntoobtain
correctheight.Removelegrestassemblybyliftinguponthegoosenecktoremoveitfromthereceiverofthe
front support.
Elevating Leg Rest
Adjusttheheightofthelegrestbydepressingsnapbuttonandslidingfootplatemountupordowntoobtain
correctheight.Adjusttheangleofthelegrestupwardbylifting,lowerbydepressingthetab.
Arm Rests
Height-Adjustable Arm Rests
To raise the arm, push up on the armlock cap and pivot back the entire armrest. To lower the arm, pull down on
the front of the armrest until the arm latch locks onto the securing stud under the arm pivot.
Flip-Up Arm Rests
To raise the arm up, pivot the arm lock lever away from the armrest and armrest lock. Lift up on the armrest.
Removebydepressingthesnapbuttonandslidingitoutofthearmrestpivot.
Serialnumberislocatedonthe
frame behind the wheel.
9
Buckle
10
DATE OF MANUFACTURE
SEE INSTRUCTIONS FOR USE
MANUFACTURER
SYMBOL LEGEND
!
!
CAUTION/ATTENTION
SERIAL NUMBER
SN
Please be environmentally responsible and
recycle this product through your recycling
facility at its end of life.
Afin de préserver l’environnement, veuillez
confier ce produit à votre centre de recyclage
à la fin de sa durée de vie.
Usage(cont.)
Casters
Lockingcasters:Tolockcasters(option),pushdownonthefrontofthecasterbrakelever.Toreleasecaster
brake, push down on the rear of the caster brake.
Removing Casters:Loosenthenremovetheself-lockingnutandmachinescrewthatareinthechairframe
wherethecasterswillbeinserted.Insertcastersothatitisushwiththeframe.Re-insertthescrewthroughthe
holes in the chair frame and caster stem. Note: Screw head should be to the outside of the frame and the nut to
the inside.HandstartthenutontotheendofthescrewUseawrenchandhexkeytotightenthecastersinto
place.Repeatforsecondcaster.
Wheels
Quick Release Axle
Depressbuttonontheaxleendtorecesstheballlockingpinsandstarttheboltthruthewheel.Placewasher
on bolt end to inside of wheel. Continue depressing the button to insert the bolt into the wheel mount.
Note: The ball locking pins will secure the axle in place when the button is released.
Wheel Locks
To engage the wheel lock, push forward on the lever, to unlock pull back on the lever.
Note: If the wheel moves while wheel lock is engaged, the assembly needs to be moved slightly closer to
the wheel.
Belts
Hook and Loop Fasteners
Pullthebeltstripsaparttoseparatethem.Adjustthestripstotheproperposition.Pressthebeltstripstogether
to connect them.
Snap Fit Buckle
To unbuckle, depress the two spring arms on the male end and pull/slide to separate it from the female receiver.
To buckle, insert the male end into the female receiver until the spring arms secure. Listen for clicking sound to
indicateitissecure.Pullstrapthrumaleportionofbuckletotighten.
Abductor/Deector
Slidedeectorintothefrontopeningoftheseat.
Swing Away Adjustable Laterals
To swing the lateral back out of the way, depress the button, pull lateral back around behind the back. To make
widthadjustments,loosenscrews,slidelateralleftorrightinbrackettodesiredposition,tightenscrew.
Check all fasteners (snap buttons, screws, nuts, bolts, clips, pull pins, handles, etc.) for tightness and make sure
they are secure.
Maintenance
•ItisnecessarytoinspectyourShower/Commodechairatleastweeklytoensureitisinsafeoperatingcondition.
•Checkallfasteners(snapbuttons,screws,nuts,bolts,clips,pullpins,handles,etc.)toensuretheyarepresent
and secure.
•Checkupholsteryfortearsandcracks.
•Checkbeltsforfraying,cuts,tears,broken/wornstitchingandbucklesforcracksordamage.
•Checkwheels,casters,andtiresforatspots,cracks,andwear.
•Checkwheellocksorcasterlocksfortightnessandproperfunction.
•Wheellocksmayneedtobeadjustedastiretreadwears.
•Wheellockfastenersmayneedtobetightened.
•Ensurehandrimsareproperlysecuredtowheels.
•Replacedamagedorworncomponents.ContactyourSupplierforrepair/replacementofsaidpartsbefore
continuing use of the shower/commode chair.
•UseonlyrecommendedActiveAidreplacementparts;useofanyotherpartsmayvoidyourwarrantyandcause
damage to your device.
•Aftereachshoweruse,rinsethedevicewithwatertoremovesoapresidue.Usingasoftnon-abrasiveclothor
sponge, wipe the device down to remove water accumulation and product build up. Allow to dry completely
before storing.
•Whencleaningtheunit,useamilddetergentwithasoftnon-abrasiveclothorsponge.Donotuseharsh
cleaning solvents or an abrasive cleaning agent.
•Upholsterypadsmaybecleanedwithanon-abrasive,non-alcohol-basedsoaporsanitizedusingableach
dilutionofupto1:10.Note,manyanti-bacterialanddisinfectantproductscontainalcoholandshouldnotbe
usedontheupholstery,duetothedryingeectofthealcohol.Chooseanon-alcohol-basedsanitizer.
GermicidalwipesthatareratedtokillC-dicilesporesmaybeusedontheupholsteryandtheepoxycoated
stainless steel.
•UrethaneCoatedFabricsmaybecleanedwithaspongeordampclothtowipethesurfacecleanwithwarm
water. As needed, they may be hand washed using warm water and a mild detergent. Do not use bleach. Line
dry. Do not iron. Do not dry clean.
Cleaning/Disinfecting
Whenaskingyoursuppliertoorderreplacementparts,pleasespecifytheserialnumberofthe922unit.
YourSupplierwillcontactActiveAidCustomerServicetoobtainthenecessaryitemsforyourspecicunit.
Ifyouhaveanyquestions,pleasecontactyourlocalsupplierorcallActiveAid,LLCat1-800-533-5330or
1-507-644-2951.
PartsReplacement
11
This warranty is extended only to the original purchaser/customer (or supplier non consumer who does not buy
or resell). ActiveAid, LLC, warrants the 922 against defects in materials and workmanship as listed below.
• StainlessSteelFrames–3yearwarranty
• Brakemechanisms,lockingmechanisms,wheelsandcasters–1yearwarranty
• Othermetalandstructuralpartsnotofstainlesssteel--1yearwarranty
• Upholsteredcomponents,plasticpads,rubberparts,paintedsurfaces,bearingsandotherpartsnot
specicallyidentiedabove–6monthswarranty
The warranty period commences on the original ship date from ActiveAid. Any product proven to ActiveAid’s
satisfaction to be defective and within warranty period shall be repaired or replaced at ActiveAid’s option.
ACTIVEAID’sSOLEOBLIGATIONANDYOUREXCLUSIVEREMEDYUNDERTHISWARRANTYSHALLBE
LIMITEDTOSUCHREPAIRAND/ORREPLACEMENT.Thiswarrantydoesnotincludeanylaborcharges
incurredinreplacementpartsinstallation.Forwarrantyservice,pleasecontacttheauthorizedsupplierfrom
whom you purchased your ActiveAid product. In the event you do not receive satisfactory warranty service,
please contact ActiveAid at the address below. Do not return products to our factory without prior
authorization.
LIMITATIONSANDEXCLUSIONS:Theforegoingwarrantyshallnotapplytoserialnumberedproductsifthe
serialnumberhasbeenremovedordefaced.Productssubjecttonegligence,abuse,misuse,improper
maintenance, improper storage, or damages beyond ActiveAid’s control are not covered by this warranty, and
thatevaluationwillbesolelydeterminedbyActiveAid.ProductsmodiedwithoutActiveAid’sexpresswritten
consent(includingbutnotlimitedto,modicationthroughtheuseofunauthorizedpartsorattachments)arenot
covered by this warranty. The warranty shall not apply to problems arising from normal wear or failure to follow
instructions. The warranty will be void if parts not manufactured by ActiveAid or parts not complying with
originalequipmentspecicationsareaddedtoanActiveAidproduct.
THEFOREGOINGWARRANTYISEXCLUSIVEANDINLIEUOFALLOTHEREXPRESSWARRANTIES.
ACTIVEAIDSHALLNOTBELIABLEFORANYCONSEQUENTIALORINCIDENTALDAMAGESWHATSOEVER.
ActiveAid maintains a policy of continual product improvement and reserves the right to change features,
specications,andpriceswithoutpriornotication.CheckwithActiveAidforlatestinformation.
ActiveAid, LLC.
101ActiveaidRoad•RedwoodFallsMN56283USA
800•533-5330•PH(507)644-2951•FAX(507)644-2468•[email protected]
activeaid.com
OWNER’S MANUAL
922
ActiveAid products should only be used under the guidance of a physician. ActiveAid maintains a policy of continual product improvement and reserves the
right to change features, specications, and prices without prior notication. Check with ActiveAid for latest information. FORM 922MAN 121819 REV A
Copyright © 2019 ActiveAid, llc. All rights reserved. Printed in the U.S.A.
LimitedWarranty
12
Please ensure the Owner’s Manual stays with the unit at all times.
Table of contents
Other ActiveAid Wheelchair manuals
