adairs Barber User manual

03/15 1
Barber side table
Thank you for purchasing this Barber side table. Please read the instructions carefully before use to ensure
safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary tools
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the retailer from whom you bought this
product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 20 MINUTES to assemble with 1 PERSON.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
adairs.com.au
adairs.co.nz

03/15 2
Fittings and parts checklist
There will be a small quantity (10%) of extra spare fittings included
A Table top x 1
B Shelf x 1
C Front leg x 1
D Shelf leg top x 2
E Shelf leg bottom x 2
adairs.com.au
adairs.co.nz

03/15 3
Step by step assembly instructions
Step One
Carefully place the table top (part A) upside down on a soft, flat surface near where the table will be used.
Locate the front leg (part C) into the bracket highlighted with a label. Turn clockwise by hand until tight.
Repeat this step with the shelf leg tops (part D).
Step Two
Position the shelf (part B) as shown below.
C
A
D
B
adairs.com.au
adairs.co.nz

03/15 4
Step Three
Screw the shelf leg bottoms (part E) in place as shown below. Ensure all legs are firmly screwed and check
periodically to ensure safe use of the table.
Step Four
Carefully turn the table over to place in position. Please note, the table should always lifted and not dragged
on the floor when moving to prevent damage to the legs.
D
adairs.com.au
adairs.co.nz

Care and Maintenance
Wood furniture
•Wood displays different grain patterns depending on which way they cut - for example, the ‘medullary
ray’ which can appear is a mark of good quality timber - these are just characteristics of the natural
beauty of the wood. Some furniture is also deliberately aged and rustic.
•Wood veneers also allow distinctive patterns to be created on flat surfaces, such as table tops and
drawer fronts by the way the slivers are arranged.
•All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade
from items that have been previously purchased.
How to care for your wood furniture
•Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
•Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by
building up over time.
•Make sure all surfaces are protected from heat and liquids by mats and coasters. Wipe up spills
immediately and ensure that a mat or pad is placed under paper if you are writing.
•Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next
to heat sources such as radiators or fires. Be particularly careful with solid wood as the lack of
humidity caused by central heating can cause damage such as warping.
Safety instructions
PLEASE READ!
This veneered cabinet top has a natural open grain finish. Please read the care guide
thoroughly. We recommend using mats and wiping up spilled liquids. Avoid placing plant
pots or vases without waterproof mats to prolong the life of this product.
•Never drag furniture when moving it, always lift it.
•Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
•Please take care when handling or moving the furniture, careless handling may cause damage or injury.
•Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
person. No liability will be accepted for damage or injury caused by incorrectly installed or
assembled furniture.
•It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all fittings
when doing this.
5
adairs.com.au
adairs.co.nz

6
adairs.com.au
adairs.co.nz

F
G
H
ANCHOR points fitting
Step 3: Use strap connect product with the wall
I
H
Required Tool
x 1 x 2 x 2 x 1
H
G
FI
Step 1: fix the fittings on the back of product.
Step 2: Example of fixing the fittings on the wall.
* Not supplied, it depends on the material and circumstances of the wall
B
C
**
7
adairs.com.au
adairs.co.nz