adairs Swansea King Full Bed User manual

1LARBDK-CNDM-07/23 adairs.com.au
adairs.co.nz
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product.
People to assemble Tools required
Please check the pack contents before attempting to assemble this product.A full checklist of components
is given in this leaet. If any components are missing, please contact the retailer from whom you bought this
product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The ttings pack contains SMALL ITEMS which should be KEPT AWAY FROMYOUNG CHILDREN.
Read this leaet in full before commencing assembly.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Swansea King Full Bed

2LARBDK-CNDM-07/23 adairs.com.au
adairs.co.nz
Fittings and parts checklist
Fitting checklist
G
Bolt
x2
M6x40mm
H
Threaded rod
x8
M8x80mm
IFlat washer
x8 J
Hexagon nut
x8
M8
KHalf-moon washer
x8 L
Wooden dowel
x4
Dia10x50mm
M
Screw
x8
Dia4x25mm
NSpanner
x1
OAllen key #4
x1
Parts checklist
AHeadboard
x1 BFootboard x1
CSide rail
x2 DCentre rail x1
ESlat assembly
x1 FSupport leg x2

3LARBDK-CNDM-07/23
Step by step assembly instructions
adairs.com.au
adairs.co.nz
Step One
With 2 people, carefully place the headboard (part A) and foot board (part B) on a soft, at surface near where
the unit will be used. Screw the threaded rod (part H) into the xing point on the heardboard and footboard
until nger tight, as shown below.
Step Two
With 2 people, locate the side rail (part C) with 1x wooden dowel (part L) and 2x threaded rod that already
assembled in step 1 as shown below.
A
B
C
L
H
x4
H
Tip: lean the headboard upright against
a wall to make this step easier.

4LARBDK-CNDM-07/23
Step by step assembly instructions
adairs.com.au
adairs.co.nz
Step Three
Secure the side rail (part C) to headboard using the half-moon washer (part K), at washer (part I), hexagon nut
(part J) and spanner (part N) as shown below.
Finally, repeat the process<from step 2 to step 3> again to secure the remaining bottom rail to the other side of
the headboard (part A).
Step Four
With 2 people, locate the footboard (part B) with wooden dowel (part L) and threaded rod that already
assembled in step 1 as shown below.
B
KI
J
J
I
K
N
C
L
x2

5LARBDK-CNDM-07/23
Step by step assembly instructions
adairs.com.au
adairs.co.nz
Step Five
Secure the footboard (part B) to side rails using the half-moon washer (part K), at washer (part I), hexagon nut
(part J) and spanner (part N) as shown below.
Step Six
Screw the adjustable feet of support leg (part F) all the way into the leg.This will be adjusted in a later step.
F
K
I
J
J
I
K
N
x2
x2

6LARBDK-CNDM-07/23
Step by step assembly instructions
adairs.com.au
adairs.co.nz
Step Seven
Locate the centre rail (part D) and x the support legs (part F) using the bolt (part G) and allen key (part O).
Step Eight
Secure the centre rail (part D) using the screw (part M) and screwdriver(not included) as shown below.
D
M
x2
x2
G
O
F
F
D

7LARBDK-CNDM-07/23
Step by step assembly instructions
adairs.com.au
adairs.co.nz
Step Nine
With 2 people, carefully move the bed into it’s intended location. Adjust the feet on the support legs (part F),
turn until they both sit at 5mm above the hard part of the oor.
Step Ten
Secure the slat assembly (part E) using 6x screws (part M) and screwdriver(not included) as shown below.
M
E
x6
5mm
Floor

8LARBDK-CNDM-07/23 adairs.com.au
adairs.co.nz
PLEASE READ!
This product has a natural open grain finish. Please read the care guide thoroughly.
Wood furniture
•Wood displays different grain patterns depending on which way they cut - for example, the
‘medullary rays’ which can appear is a mark of good quality timber - these are just characteristics of the
natural beauty of the wood. Some furniture is also deliberately aged and rustic.
•Wood veneers also allow distinctive patterns to be created on at surfaces, such as table tops and drawer
fronts by the way the slivers are arranged.
•All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade
from items that have been previously purchased.
How to care for your wood furniture
•Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
•Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by building
up over time.
•Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next
to heat sources such as radiators or res. Be particularly careful with solid wood as the lack of humidity
caused by central heating can cause damage such as warping.
Care and Maintenance
•Never drag furniture when moving it, always lift it.
•Periodically check all xings to ensure none have come loose and re-tighten where necessary.
•Please take care when handling or moving the furniture, careless handling may cause damage or injury.
•Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
person. No liability will be accepted for damage or injury caused by incorrectly installed or assembled
furniture.
•It is recommended that before moving heavy objects to a new location they are completely dis- assembled
to avoid personal injury or damage to the furniture. Please be careful to retain all ttings when doing this.
Safety instructions

9LARBDK-CNDM-07/23 adairs.com.au
adairs.co.nz
Experiencing problems with your new product?
Before calling customer service, please have your item’s batch code ready.
You can nd the batch code on the back or bottom of your product as below shown.
(example batch code: 190510)
Batch Code
Placement