AdDent Calset User manual

GENERAL
The Calset unit is designed to heat composite material, anesthetic solution and porce-
lain veneers. The Calset unit accepts composite from compules or syringed material.
A tray placed on the top of the heater will either hold compules, or will have a holder
for your composite dispenser. There are other trays available and are described in
Intended Use.
A plastic spatula should always be used to remove composite to avoid
scratching the non-stick surface.
If the Compule Tray is used, it is recommended that the compule be placed in the
composite dispenser immediately after it is warmed and placed in the mouth within 30
seconds.
INTENDED USE
The basic Calset unit is used for warming dental composite materials. Accessories for
the Calset are as follows:
1. Tri-Tray – For warming composite inside of dispenser gun to 155°F (68°C),
 andwarming2nishinginstruments.3extracompulesmayalsobewarmed.If
 usingtheAdDentCoMaxCompositeDispenser,theTri-Trayenablesyoutopick
up the compules without touching the compule
2. Dispenser Gun Tray – For warming composite inside of dispenser gun to
155°F (68°C).
3. Anesthetic Carpule Tray – For heating anesthetic compules to 98°F (37°C).
4. Syringe Tray – for heating the syringed material to 155°F (68°C).
5. Porcelain Veneer Tray – for heating the composite in the back side of the veneer
to 155°F (68°C). Keep lid on for 3 minutes of warming.
DESCRIPTION OF UNIT
A universal power supply (100-240 VAC, 50/60 hertz) provides power to the heater. A
circular control housing contains a microprocessor and the heater assembly. Around
the perimeter of the housing are the power connector, a control switch, and 2 LED
lights. The housing has a non-stick coated metal top plate to conduct the heat from
the heater to the tray. The tray has a cover and a plastic ring assembly to enable
the hot tray to be picked up comfortably. The Calset will turn off after 10 hours of
unattended use.
INSTRUCTIONS FOR USE
CALSET ACCESSORY PART #S:
P/N 600003 - Standard Tray
P/N 600067 - Tri-Tray
P/N 600047 - Dispenser Tray
P/N 600059 - Anesthetic Tray
P/N 600064 - 7 Hole Tray
P/N 600066 - Porcelain Veneer Tray
MANUFACTURER
AdDent, Inc.
43 Miry Brook Road, Danbury CT 06810
Phone: [phone]
  Fax:203-792-2275
Email: [email protected]
Website: www.addent.com
!
ADDENT, INC. 43 MIRY BROOK ROAD, DANBURY CT 06810
PHONE: [phone] | FAX: [phone]
EMAIL: [e-mail] | WEBSITE: WWW.ADDENT.COM
P/N 660021 03/2013
ISO CERTIFIED !

!
OPERATION OF CALSET
Plug the universal power supply into a suitable outlet. Connect the power plug into the
power connector MAKING SURE THAT IT IS FULLY SEATED. Put a gun dispenser,
syringe, anesthetic, or porcelain tray on top of the heater. The following is a list of the
push button switch functions with regard to temperature and LED color indicators.
The push button will scroll through three temperatures as follows:
Push Button LED Color Temperature
Push 1 time Green 98°F (37°C)
Push 2nd time Orange 130°F (54°C)
Push 3rd time Red 155°F (68°C)
  Holdfor2seconds ― TurnOff
The amber (yellow) LED on the right side of the unit turns on when the switch is
depressed. This indicates that the wall plug and power plug are properly connected
totheunit.Inapproximately14minutesthedesiredtemperatureisreachedandthe
LEDstopsashing.
OVER TEMPERATURE
The Calset has a back up thermostat that will shut down the Calset if the temperature
exceedstheprogramvalue.Thelightswillgooutandtheunitwillcooldown.When
the thermostat resets, it may be possible to re-energize the Calset, but if it shuts down
again, return the Calset for repair.
Disinfection
The Calset unit can be disinfected to prevent cross contamination. The
top tray is autoclavable, or can be wiped with a cloth and disinfectant. The plastic
housing should only be wiped using a disinfectant and should not be sprayed. DO
NOT AUTOCLAVE THE BOTTOM HEATING TRAY.
Caution
The Calset operates HOT. Care should be taken to avoid touching hot
surfaces. The tray has a plastic cover and plastic rings for handling. If the tray is to be
taken off the control housing, the heater should be turned off so that the top plate will
cool. This is achieved by holding the control switch in for 2 seconds until amber light
goes off. The unit will then turn off and the top plate will cool.
ACCESSORY TRAYS
Tri-Tray –Holdsdispensergunand2nishinginstruments.ForusewithCoMax
(AdDent), Caulk, Kerr (original model), SDI, and Clinicians Choice
Dispenser Gun Trays―forusewith3M,Kuraray,Vident,CentrixNu-Gunand
Vivadent Guns. Visit website for PN’s. www.addent.com
Anesthetic Tray – Holds 3 anesthetic carpules. For use only with 98°F (37°C)
Temperature setting (Green LED).
Porcelain Veneer Tray – To cement veneers with composite
Syringe Tray – For composite syringes
TRI-TRAY GUN TRAY
USE OF TRI- TRAY
When placing the composite compule
gun into the opening for heating, be sure
the groove at the top of the sleeve lines
upwiththeoriceofthecompuleinthe
dispenser gun.
DISINFECTION INSTRUCTION FOR DISPENSER GUN TRAY
To clean, remove the plastic sleeve and top. The sleeve and the top can be
cold sterilized. The metal tray can be autoclaved or cold sterilized. A Q-tip with
disinfectant can be used to clean out the middle of the tray.
DO NOT AUTOCLAVE THE BOTTOM HEATING TRAY
!
!
!
Your favorite composite
nishinginstruments
Spare Compules
LED Indicators