ADDER AdderLink XD150 User manual

AdderLink XD150
User Guide
Experts in
Connectivity
Solutions
Extender
Solutions

INSTALLATION
1
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Introduction
Welcome................................................................................................................2
AdderLink XD150 features................................................................................3
Tips for achieving good quality links ................................................................4
Supplied items.......................................................................................................5
Optional extras.....................................................................................................6
Installation
Locations................................................................................................................7
Connections ..........................................................................................................8
Local video connection.................................................................................8
Local USB connection...................................................................................8
Local audio connection.................................................................................9
Local serial port connection........................................................................9
Local data link connection............................................................................9
Local power connection.............................................................................10
Remote video connection..........................................................................11
EDID management.................................................................................11
Remote USB connections ..........................................................................11
Remote audio connection..........................................................................12
Remote serial port connection.................................................................12
Remote data link connection.....................................................................12
Remote power connection........................................................................13
Conguration
Mode switch settings.........................................................................................14
Firmware upgrades ............................................................................................15
Operation
Indicators .............................................................................................................16
Further information
Getting assistance ..............................................................................................17
Appendix 1 - Options port pin-out ...............................................................18
Appendix 2 - Link cable interference protection........................................19
Warranty..............................................................................................................20
Safety information..............................................................................................20
Radio frequency energy....................................................................................21
Index
Contents

INSTALLATION
2
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Introduction
WELCOME
Thank you for choosing the AdderLink XD150 extender modules.These compact
modules allow you to transfer the following connections up to 150 meters from your
computer via a single link cable:
• High quality single link DVI digital video,
• USB keyboard and mouse plus two other USB devices (up to version 2.0),
• An RS232 serial device at speeds up to 115200 baud,
• Stereo speakers.
Thanks to our long involvement and investment in extender
technology we have succeeded in overcoming the
numerous problems associated with extending high
speed signals.
The AdderLink XD150 extender modules
are totally transparent in operation, leaving
you free to use your computer as
though you’re still sitting next to it.
Higher rate or longer reach?
The AdderLink XD150 extenders provide two operational modes so that you can
choose your priority:To support a higher resolution display (up to 1920 x 1200 @ 60Hz)
or to cover a greater distance (up to 150 meters).A simple switch setting on the
local module determines the required mode.When the high rate mode is enabled, the
XD150 system will continually monitor the data link to ensure that image quality is
beingmaintained.Ifthedatalinkisnotsufcient,thelocalmodulewillautomaticallyfall
back to long reach mode.
See also:
• Tips for achieving good quality links
• Mode switch settings

INSTALLATION
3
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
ADDERLINK XD150 FEATURES
The local and remote modules are contained within slimline metal casings that measure
just 169 x 116 x 31mm.
CATx link to
remote module
Do not connect to
network devices of
any kind. See Local
data link connection
for further details.
Recessed
reset
button
Status indicators
These provide
visualconrmation
of various system
functions. See
Indicators for further
details.
Power input
See Local power
connection for
further details.
Mode switches
These allow you to
determinespecic
behaviors. See Mode
switch settings for
further details.
Upgrade port
Usedforrmware
upgrades to
both modules.
See Firmware
upgrades for
further details.
Options port
Used for RS232
serial devices. See
Local serial port
connection for
further details.
Video port
Connects to the
DVI-D video
output port of your
computer. See Local
video connection for
further details.
USB port
Connects to a
USB port on your
computer. See Local
USB connection for
further details.
Audio port
Connects to the
speaker/audio
output port of your
computer. See Local
audio connection for
further details.
Local module
USB ports
Connect your USB
keyboard, mouse
and other devices.
See Remote USB
connections for
further details.
Status indicators
These provide
visualconrmation
of various system
functions. See
Indicators for further
details.
Power input
See Remote
power
connection for
further details.
USB ports
Connect your USB
keyboard, mouse and
other devices. See
Remote USB connections
for further details.
Options port
Used for RS232
serial devices. See
Remote serial
port connection
for further details.
Video port
Connects to
your DVI-D
video display. See
Remote video
connection for
further details.
Audio port
Connects to your
speakers. See
Remote audio
connection for
further details.
CATx link to local
module
Do not connect to
network devices of any
kind. See Remote data
link connection for
further details.
Remote module

INSTALLATION
4
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
TIPS FOR ACHIEVING GOOD QUALITY LINKS
Due to the large volumes of data that must be transferred between the local and remote
modules, every AdderLink XD150 installation is highly dependent upon good quality
CATx cable links.Video performance is particularly reliant on high speed communication
channels. For this reason, the AdderLink XD150 units test the link quality to determine
which of two transfer modes can be supported: High rate or Long reach.
The main factors that affect link quality are:
• The length and type of CATx cable used,
• The number, length and type of intermediate patch connections,
• The quality of the cable terminations.
Patch cables
As mentioned above, patch links affect performance. For each additional break/patch
within a run, you will need to reduce the distance given above by roughly 5 meters.
For best results, patch cables should be of type CAT 7a and be less than 2 meters in
length. If patch cables are greater than 2 meters, then they must be CAT 7a.
Adder recommend the following CAT 7 shielded, foiled, twisted pair cables:
• Flexible patch cable Daetwyler 7702 (26AWG S/FTP)
• Bulk cable Daetwyler 7120 (23AWG S/FTP)
Long reach mode
•CAT7a,CAT6aorCAT5esolidcorebulkcable
•24AWG(Ø0.5106mm)orthickercores
•U/UTP,F/UTPorbetterscreening
•MaximumoftwoCAT7apatchconnections
Please see Appendix 2 - Link cable interference protection
for details about cable screening and shielding.
High rate mode
•CAT7asolidcorebulkcable
•23AWG(Ø0.574mm)orthickercores
•S/FTP,S/STPorPiMFscreening
•MaximumoftwoCAT7apatchconnections

INSTALLATION
5
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
SUPPLIED ITEMS
Information wallet
containing:
Eight self-adhesive rubber feet
Safety document
AdderLink XD150
local module
2 x Power adapter with
locking connector and
country-specic power
cord
AdderLink XD150
remote module
Video cable DVI-D to DVI-D
USB cable 2m (type A to B)

INSTALLATION
6
CONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
OPTIONAL EXTRAS
Audio cable 2m (3.5mm stereo jacks)
Part number:VSC22
USB cable 2m (type A to B)
Part number:VSC24
Replacement power adapter
with locking connector
Part number: PSU-IEC-12VDC-1.5A
Country-specic power cords
CAB-IEC-AUS (Australia)
CAB-IEC-EURO (Central Europe)
CAB-IEC-UK (United Kingdom)
CAB-IEC-USA (United States)
CAB-IEC-JAPAN (Japan)
Serial cable 2m
Part number:VSC40
Single link DVI-D to DVI-D video cable
Part number:VSCD1

7
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Installation
LOCATIONS
Please consider the following important points when planning the position of the
AdderLink XD150 modules:
• Situate the local module close to the system to which it will be connected and near
to a source of mains power. Place the remote module in similar close proximity to the
peripherals that it will connect with, plus a source of mains power.
• Consult the precautions listed within the Safety information section.
HT

8
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
CONNECTIONS
Connections do not need to be carried out in the order given within this guide, however,
where possible connect the power inasanalstep.Thelocalmoduleconnectstoyour
computer while the remote module links with your peripherals.
Local video connection
When operating in High Rate mode,AdderLink XD150 can support one Single Link DVI
video display at pixel clocks up to 165MHz (equivalent to a maximum resolution of 1920
x 1200 at 60Hz - aka ‘WUXGA’). If the Long Reach mode is selected, pixel clocks up to
148.5MHz (equivalent to a maximum resolution of 1920 x 1080 at 60Hz - aka ‘1080P’)
are supported.This allows greater separation between the local and remote modules to
be achieved. Please see the section Mode switch settings for details.
To connect the video port
1 Connect the supplied digital video link cable
between the DVI-D socket on the local
module rear panel and the DVI-D video output
socket of your host computer.
From video output
socket on your
host computer
Local USB connection
If USB connectivity is required, then a single USB connection is necessary between the
local module and your computer; the AdderLink XD150 remote module acts as a USB
2.0 hub and thus provides four sockets for your peripherals.
To connect the USB port
1 Connect the supplied USB cable between the USB
port on the local module rear panel and a vacant
USB socket on your host computer.
From USB socket
on your host
computer

9
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Local audio connection
The AdderLink XD150 modules support stereo speakers.A connection to the audio
output port of the host computer is required at the local module.
To connect the audio port
1 Connect an audio link cable (Adder
part number:VSC22) between the
audio socket on the local module rear
panel and the speaker/audio output
socket of your host computer.
From audio output
on your computer
Local data link connection
The local and remote modules require a direct connection between them using standard
CATx cables and connectors.This is a proprietary data link and is NOT network
compatible; the modules must NEVER be connected to any networking equipment, such
as switches and routers.
When operating in High Rate mode,AdderLink XD150 can support cable distances up
to 100 meters. If the Long Reach mode is selected, the separation between the local and
remote modules can be increased to 150 meters. Best results will be gained when single
lengths of CAT7 cable are used without the need for patch cables.
To connect the data link cable
1 Connect the CATx cable from
the remote module to the
LINK port on the front panel of
the local module.
From
AdderLink XD150
remote module
Local serial port connection
The Options port provides an RS232 serial connection with the remote module.When
serial devices are attached to the Options ports on the local and remote modules, the
units transparently convey the signals between them, via the CATx link, at rates up to
115200baud-noserialcongurationisrequired.Anoptionalserialcable(partnumber:
VSC40) is available from Adder.
To connect the serial port
1 Use the optional serial cable (VSC40) to
link the Options port on the rear panel
of the local module with a vacant RS232
serial port on your host computer.
Please see Appendix 1 for pin-out details of the Options port.
From the serial port of
your host computer
This is NOT an ethernet/network
port and must NEVER be connected
to any networking equipment.
This is NOT an ethernet/network
port and must NEVER be connected
to any networking equipment.

10
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Local power connection
There is no on/off switch on either of the AdderLink XD150 modules, so operation
begins as soon as power is applied.The power adapters supplied with the modules
use locking-type plugs to help prevent accidental disconnections; please follow the
instructions given right whenever disconnecting a power adapter.
To connect the power adapter
1 Attach the output plug of the supplied power adapter to the
power input socket on the left side of the rear panel.
2 If any mode changes need to be made, adjust the switch settings before applying power
to the local module. Please see the section Mode switch settings for details.
3 ConnecttheIECconnectorofthesuppliedcountry-specicpowercordtothesocket
of the power adapter.
4 Connect the power cord to a nearby main supply socket.
To disconnect the power adapter
1 Isolate the power adapter from the mains supply.
2 Grasp the outer body of the power adapter plug
where it connects with the module.
3 Gently pull the body of the outer plug away from
the module.As the body of the plug slides back,
it will release from the socket and you can fully
withdraw the whole plug.
IMPORTANT: Please read and adhere to the electrical safety information
given within the Safety information section of this guide. In particular, do not
use an unearthed power socket or extension cable.
Note: Both the modules and the power supplies generate heat when in operation and will
become warm to the touch. Do not enclose them or place them in locations where air cannot
circulate to cool the equipment. Do not operate the equipment in ambient temperatures
exceeding 40 degrees Centigrade. Do not place the products in contact with equipment whose
surface temperature exceeds 40 degrees Centigrade.
From the
power adapter
Gently pull back the plug outer
body to release the lock

11
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Remote video connection
A Single Link DVI-D port is provided on the rear panel of the remote module.The
bandwidth available at the port is determined by the video input at the local module and
also the mode in which the AdderLink XD150 system is running.When high rate mode
is used, the modules will continually check the link quality to ensure that it is capable of
supporting the higher pixel clock. If excessive data errors are detected, the modules will
fall back to Long Reach mode until the local module is reset or the link is broken and re-
established.
AdderLink XD150 can support one Single Link DVI video display at pixel clocks up to
165MHz (equivalent to a maximum resolution of 1920 x 1200 at 60Hz - aka ‘WUXGA’)
when operating in High Rate mode. If the Long Reach mode is selected, pixel clocks up to
148.5MHz (equivalent to a maximum resolution of 1920 x 1080 at 60Hz - aka ‘1080P’)
in order to allow greater separations between the local and remote modules to be
achieved. Please see the section Mode switch settings for details.
To connect the video display
1 Connect the DVI-D video cable from your video
display to the video output port on the rear panel
of the remote module.
From your
video display
EDID management
When a remote module is connected and the video display attached to it is detected,
theEDID(ExtendedDisplayIdenticationData)informationisclonedandstoredatthe
local module. Once this is done, a transparent DDC/CI (Display Data Channel/Command
Interface) two way communication link is provided between the video display and the
video source (your host computer). If the remote monitor is removed then the cloned
EDID stored at the local module will still be presented to the video source.
Remote USB connections
The remote module contains a USB hub that can support up to four v1.1 or v2.0 USB
devices (in any combination).All four USB sockets are identical in operation.
To connect USB devices
1 Connect your USB keyboard, mouse and any other
two USB devices to the four sockets distributed on
the front and rear panels of the remote module.
From USB
devices
From USB
devices
Rear panel
Front panel

12
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Remote audio connection
The AdderLink XD150 modules support stereo speakers.
To connect your speakers
1 Connect your speakers to the audio socket on the
remote module rear panel.
From your speakers
Remote data link connection
The local and remote modules require a direct connection between them using standard
CATx cables and connectors.This is a proprietary data link and is NOT network
compatible; the modules must NEVER be connected to any networking equipment, such
as switches and routers.
When operating in High Rate mode,AdderLink XD150 can support cable distances up
to 100 meters. If the Long Reach mode is selected, the separation between the local and
remote modules can be raised up to 150 meters. Best results will be gained when single
lengths of CAT7 cable are used without the need for patch cables.
To connect the data link cable
1 Connect the CATx cable from the local module
to the LINK port on the rear panel of the remote
module.
From AdderLink
XD150 local module
Remote serial port connection
The Options port provides an RS232 serial connection with the local module.When
serial devices are attached to the Options ports on the local and remote modules, the
units transparently convey the signals between them, via the CATx link, at rates up to
115200baud-noserialcongurationisrequired.Anoptionalserialcable(partnumber:
VSC40) is available from Adder.
To connect the serial port
1 Use the optional serial cable (VSC40) to
link the Options port on the rear panel
of the remote module with your RS232
serial device.
Please see Appendix 1 for pin-out details of the Options port.
From your serial device
This is NOT an ethernet/network
port and must NEVER be connected
to any networking equipment.
This is NOT an ethernet/network
port and must NEVER be connected
to any networking equipment.

13
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Remote power connection
There is no on/off switch on either of the AdderLink XD150 modules, so operation
begins as soon as power is applied.The power adapters supplied with the modules
use locking-type plugs to help prevent accidental disconnections; please follow the
instructions given right whenever disconnecting a power adapter.
To connect the power adapter
1 Attach the output plug of the supplied power adapter to the
power input socket on the left side of the rear panel.
2 ConnecttheIECconnectorofthesuppliedcountry-specicpowercordtothesocket
of the power adapter.
3 Connect the power cord to a nearby main supply socket.
IMPORTANT: Please read and adhere to the electrical safety information
given within the Safety information section of this guide. In particular, do not
use an unearthed power socket or extension cable.
Note: Both the modules and the power supplies generate heat when in operation and will
become warm to the touch. Do not enclose them or place them in locations where air cannot
circulate to cool the equipment. Do not operate the equipment in ambient temperatures
exceeding 40 degrees Centigrade. Do not place the products in contact with equipment whose
surface temperature exceeds 40 degrees Centigrade.
From the
power adapter
To disconnect the power adapter
1 Isolate the power adapter from the mains supply.
2 Grasp the outer body of the power adapter plug
where it connects with the module.
3 Gently pull the body of the outer plug away from
the module.As the body of the plug slides back,
it will release from the socket and you can fully
withdraw the whole plug.
Gently pull back the plug outer
body to release the lock

14
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Conguration
MODE SWITCH SETTINGS
The local module has two small switches on its rear panel.These are used to determine
which operation modes should be used.You will need to re-power the local module
whenever a switch setting is changed.
Switch B
Link mode
Determines the priority for the data link:
Longer distance or higher screen resolution.
UP - Long reach mode - Limits the pixel clock (148.5MHz)
so that longer stretches of link cable (exceeding 100m) can be
used. This will restrict the achievable screen resolution to a
maximum of 1920 x 1080 at 60Hz (aka ‘1080P’).
DOWN - High rate mode - Allows a higher pixel clock
(165MHz) to support screen resolutions of up to 1920 x
1200 at 60Hz (aka ‘WUXGA’).This will limit the maximum
link cable length to around 100m or less, depending on the
type of link cable used.
Note:When high rate mode is used, the modules will continually
check the link quality to ensure that it is capable of supporting
the higher pixel clock. If excessive data errors are detected, the
modules will fall back to Long Reach mode until the local module
is reset or the link is broken and re-established.
Switch A
USB compatibility mode
Determines whether USB compatibility
mode should be used.
UP - Normal mode - Use this if the modules are not
connected to a KVM switch.
DOWN - Compatibility mode - Use this if either
the local or remote modules are connected to a
KVM switch.This mode ensures robust and reliable
operation with KVM switches but also reduces the
maximum USB data rate.
Local module
rear panel
Note:The default position for both
switches is UP, thus selecting Long reach
mode and high speed (normal) USB mode.
Changes to the mode switches are
not recognized until you re-apply
power to the local module.
HT

15
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
FIRMWARE UPGRADES
Both modules can be upgraded simultaneously by linking them together and then
connecting them to your computer using a USB type-A to mini-B cable.
IMPORTANT: During the upgrade process, do not remove power from either
module.
To enter upgrade mode
1 Onyourcomputer,downloadthelatestAdderLinkXD150upgradelefromadder.com.
2 Connect the local and remote modules together using a CATx cable, and power on
both modules. It’s not important whether any peripherals (if any) are attached to
either module.
3 Connect the local module to your computer
using the mini USB socket on the rear panel
and a USB type-A to mini-B cable (not
supplied).
4 On the front panel of the local module, use a small implement
or straightened paperclip to press and hold the recessed
reset button for approximately 10 seconds.
 Thefrontpanelindicatorswillbegintoash
in sequence:The outer two followed by
the inner two and so on.
The module should be declared on
your computer as a mass storage
device with the volume label
‘FIRMWARE’.
5 Useyourcomputer’slemanagerapplicationtocopytheupgradeledownloaded
earlier to the mass storage device that has the volume label ‘FIRMWARE’. Once the
local module has received all of the data, the front panel indicators of the local module
will chase from side to side to show that the upgrade procedure is underway.
6 Once the upgrade has been successfully completed both modules will reset
themselves and return to normal operation.
Errors during the upgrade process
If the upgrade process encounters an error then one or more of the indicators on the
localmodulefrontpanelwillashrapidly,i.e.theywillceasechasinginsequence.
If the rmware upgrade fails
1 Check that the CATx cable is correctly connected between the LINK sockets of the
local and remote modules and that power is applied to both modules.
2 On the front panel of the local module, re-press the recessed reset button for
approximately 10 seconds to re-invoke upgrade mode.The module should again
be declared on your computer as a mass storage device with the volume label
‘FIRMWARE’.
3 Follow step 5 above.
• If the upgrade process fails again, contact Adder technical support for assistance.


16
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
Operation
INDICATORS
The local and remote modules contain various indicators to provide you with status
information. Both modules have four red indicators on their front panels; both also have
green and amber indicators on the link connectors.
Red status indicators
The red status indicators on the front panels of each module mostly behave in the same
manner at the same time:
Power
This indicator will
be on when power
is supplied to each
module.
Activity
This indicator
willashwhen
there is USB data
owingbetween
the modules.
USB
This indicator will
be on once the
USB extender
and hub located
within the remote
module have
been successfully
enumerated by
the USB host on
your computer.
Link
This indicator
will be on once a
good link exists
between the
local and remote
modules.
Green and amber status indicators
The green and amber status indicators on the link connectors of each module provide
further status information:
Green
This indicator will be on
whenever there is a good
link between the local and
remote modules.
Amber
Thisindicatorwillash
when video data is being
transferred between the
modules.
The AdderLink XD150 modules are designed to be transparent in operation. Providing
thelinkcableissufcienttoreliablycarrythesignalsacrosstheseparationdistance,
all peripherals should respond exactly as they would when situated next to your host
computer.
HT

17
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
This chapter contains a variety of information, including the following:
• Getting assistance - see right
• Appendix 1 - Options port pin-out
• Appendix 2 - Link cable interference protection
• Safety information
• Warranty
• Radio frequency energy statements
GETTING ASSISTANCE
If you are still experiencing problems after checking the information contained within this
guide, then we provide a number of other solutions:
• Online solutions and updates – www.adder.com/support
Check the Support section of the adder.com website for the latest solutions and
rmwareupdates.
• Adder Forum – forum.adder.com
Use our forum to access FAQs and discussions.
• Technical support – www.adder.com/contact-support-form
For technical support, use the contact form in the Support section of the
adder.comwebsite-yourregionalofcewillthengetincontactwithyou.
Further information
HT

18
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
APPENDIX 1 - OPTIONS PORT PIN-OUT
The OPTIONS port uses a 10p10c socket which can accommodate both 10p10c
connectors as well as the much more common 8p8c connectors, which are used on
Ethernet leads and patch cables.The pin-outs are listed in this section for both types of
connector.
Note:Although the pins labeled ‘Not used’ are inactive, they are still connected internally and so
no links should be made at all to these pins.
8p8c 10p10c Signal
1 Not used
1 2 5VDC power output (100mA max)
2 3 GND reference for all signals
3 4 RS232 (RXD) data receive
4 5 Not used
5 6 Not used
6 7 RS232 (TXD) data transmit
7 8 Not used
8 9 Not used
10 Not used
110
OPTIONS

19
INSTALLATIONCONFIGURATIONOPERATION
FURTHER
INFORMATION
INDEX
APPENDIX 2 - LINK CABLE INTERFERENCE PROTECTION
Name Overall Screening Pair Shielding
U/UTP ûû
F/UTP üû
U/FTP ûü
S/FTP üü

or S/STP
or PiMF
U/UTP
F/UTP
U/FTP
S/FTP
S/STP
PiMF
Pair shielding
Overall screening
Outer sheath
General cable anatomy
Overall
screening
Pair
shielding
Twisted
Pair
While the Category rating (e.g. CAT 5e, CAT 6a, CAT 7, etc.)
determines the electrical performance of a cable, another vital part
oftheoverallcablespecicationisitsprotectionfrominterference.
As cabling distances and data rates increase, so too does the
susceptibility to interference, from both external and internal
sources.
Proximity to other electromagnetic sources are the main external
threat and these can be subdued using overall screening that
surrounds all four of the cable pairs. However, interference is also
possible from neighbouring twisted pairs within the same cable
and this can be just as hazardous to data integrity. Such crosstalk is
countered by shielding each cable pair separately.
Within each Category rating, you can specify different
combinations of external screening and internal shielding to suit
the environment into which the link is being placed. Please see
the section Tips for achieving good quality links for suggested
combinations.
Interference protection codes
Interferenceprotectionisnowclassiedinthefollowingmanner:
U/UTP
where
U= unshielded
F= foil shielding
S= braided shielding
PiMF = Pairs in Metal Foil