ADDER ADDERLink INFINITY 2100 User manual

Welcome
This quick start guide covers some of the key points of the ADDERLink™ INFINITY 2100 unit. Full user details
and setup instructions can be found at www.adder.com/en/kvm-solutions/adderlink-innity-2102
Please read the supplied safety instruction leaet before use.
Initial conguration
ALIF2100 units can be linked in two mains ways: Direct or Networked.
Direct linking
Where ALIF2100 transmitters and receivers are directly linked to each other, very little conguration
action is required, provided that they both have their factory default settings in place - just link them
together. If the standard settings have been changed in a previous installation, you merely need to
perform a manual factory reset on each unit. Please see the center pages.
ADDERLink™INFINITY 2100
Quick Start
© 2023 Adder Technology Limited • All trademarks are acknowledged.
Part No. MAN-QS-000055_V1.1
www.adder.com
Networked linking
Where ALIF2100 units are connected via networked links, you can either congure them individually,
or congure them collectively using an AIM server:
• Conguring networked ALIF units individually -You need to specify the network addresses
of the ALIF2100 units so that they can locate each other.This can be done using via OSD on the
console connected to the RX unit by pressing CTRL + A LT + C. Please see the rear page.
• Conguring networked ALIF units collectively - The ADDERLink™ INFINITY Management
(AIM) server allows you to congure, control and coordinate any number of ALIF transmitters and
receivers from a single application. See adder.com for details.
IMPORTANT: When using AIM to congure ALIF units, it is
vital that all units that you wish to locate and control are
set to their factory default settings. Otherwise they will
not be located by the AIM server. If necessary, perform a
manual factory reset on each ALIF unit. See center pages.
Note: If you are using one or more ALIF2100 transmitters
within an installation managed by an AIM server, the AIM
server must be running rmware version 5.3 or above.
ALIF2100 conguration via web pages
Each ALIF2100 unit hosts its own internal set of web pages which contain all conguration details
and settings.You will need to use a computer connected to the same network as each ALIF2100
unit to access the web pages. Additionally, on the console attached to the ALIF2100 RX unit, you
can access its conguration details via the On Screen Display (OSD) by pressing CTRL + A LT + C
To congure ALIF2100 units via their web pages
Run a web browser on your computer and enter the IP address of the required ALIF2100 unit:
The default addresses (if using port 1) are TX: https://169.254.1.33
RX: https://169.254.1.32
The default addresses (if using port 2) are TX: https://169.254.1.43
RX: https://169.254.1.42
The opening page should be displayed:
Full user details and setup instructions can be found at:
www.adder.com/en/kvm-solutions/adderlink-innity-2102

Connections
To perform a manual factory reset
A factory reset returns ALIF2100 unit to its default conguration.
1 Power on the ALIF2100 unit.
2 Use a long narrow implement (e.g. a straightened-out paper clip) to press-and-hold the recessed
reset button on the front panel for roughly ten seconds, until the status indicator turns blue (Note:
alternating red/green indications will occur during the ten second period while the button is still pressed).
3 Release the reset switch.The indicator will change to red for a short while (less than ten seconds)
and then back to blue while ALIF2100 unit performs the reset and should then change to an
alternative color, usually orange initially, signifying that the operation is complete.
Note: If you are performing a factory reset and intend to disconnect the power immediately after the reset,
you must wait at least 30 seconds after you have released the reset button for it to complete the process.
Teaming
ALIF2100 units are ready to automatically invoke teaming whenever
the CATx and SFP (with either CATx or ber modules installed) ports
are both used to link transmitters and receivers.Teaming potentially
doubles the available bandwidth for video intensive applications and
also provides redundancy in case one link is lost.
* The units benet from multiple audio signal streams:
• Uni-directional analog audio - from the host
PCs jack socket,
• Bi-directional digital audio - via the USB
connection (converted to/from analog),
• Bi-directional digital audio - via the video
connection.
Main status indicators
Green All services present.
Amber Running but video, USB or network link missing.
Red Booting before processor loaded or failed.
Red rapid ash Critical error has been detected (a message will
also be displayed within the OSD.)
Blue Factory reset mode active.
Red/green ash Booting into factory recovery mode.
Green/blue ash Upgrade mode active.
Fast green ash Identify mode active.