addlink SPIDER N4 User manual

AddGame SPIDER N4 DDR4
SO-DIMM Installation Guide

SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System
Introduction
Installation by professional laptop computer technician is
recommended. Before continuing with installation process, please
review the warranty policy and instructions provided by your Laptop’s or
motherboard’s manufacturer to ensure your follow proper procedures to
install your DRAM. Accordingly, by proceeding with any installation,
you agree to be solely responsible for any failure to follow any
manufacturer’s instructions.
SPIDER N4

Important Notice
1. It is recommended that you install the RAM module under
professional supervision. You may also visit an authorized service
center for further assistance.
2. To prevent your memory from damage by static electricity, before
installation, please touch an unpainted metal surface on your
computers’ frame.
3. Wear gloves or an ESD wrist strip when handling
4. Please do not use this product in a wet environment. Make sure
that you are working in static-safe environment.
5. Do not grab packages. Hold only the edged of the Memory with
both hands.
6. Disconnect all the connected peripherals, lines, power connectors,
and battery pack before removing the notebook PC compartment
cover.
7. Please review your laptop/system’s owner’s manual to ensure your
follow proper procedures to install your memory.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

Required Tools & Prepare
1. Memory Module(s) and your laptop/System
2. A Screwdriver (For removing the cover on your laptop)
3. Your laptop manual
Installation
1, Turn off your notebook.
2. Unplugging the power code from your laptop.
3. Remove the battery.
4. Discharge residual power by pressing the power button.
5. Loosen the cover screws and remove the screws from notebook
PC’s compartment cover
6. To prevent pulling on and causing damage to the cables
connected, slightly lift the cover to reveal the compartment
without removing the cover completely.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

7. Before touching the memory, ground yourself . Touch an
unpainted metal surface on your laptop’s frame or use a
grounded antistatic wrist strap to prevent electrostatic discharge
(ESD)
8. Insert your new memory modules(s). Align the memory module
notch(es) and key(s) along with the socket notch(es) and key(s)
for proper installation.
9. Push down the Memory Module until it clicks in place.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

Test It
Before you close your case, power on your computer and check your
laptop’s memory usage in Windows Task Manager or BIOS.
In Windows Task Manager, please go to the left-pane menu, then
click “Performance” and “Memory”. There, you will see the amount of
RAM that is currently being used, as well as the available memory
you can still utilize.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

Troubleshooting
If you have trouble with your new RAM, check these things first.
1. Double check your power code.
2. Check the module. Did both side clips snap to hold the module
firmly in place?
3. Check the cables and wires inside your laptop. Make sure all
the cables are firmly in their sockets.
4. Remove and reinstall the modules into the memory slot again.
5. Consult your notebook specification & installation guide. Or go
to notebook product support homepage to check currently
installed memory specification (amount, DRAM type, maximum
supported)
6. Enter BIOS and press "F5" or "F9", to help you load the default
setting for BIOS.
7. Reset BIOS by removing and replacing the CMOS battery or
through CLR_Jumper (Please follow the instruction of your
motherboard).
8. Update your BIOS.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

Close your System
1. Now just put the cover back.
2. Reconnect the power cord and reinstall the notebook battery.
3. Turn on the notebook to complete the memory upgrade
configuration.
SPIDER N4
DDR4 SO-DIMM
Installation
Guide
Introduction
Important Notice
Installation
Test it
Troubleshooting
Close Your System

HEADQUARTER
6F., No. 300, Ruiguang Rd., Neihu Dist.,
Taipei City 114, Taiwan (R.O.C.)
CONTACT INFORMATION
TEL :[phone]
FAX :[phone]
www.addlink.com.tw