ADEMCO VISTA-20SE Owner's manual

VISTA-20 SE
2-PARTITIONED
SECURITY SYSTEM
PROGRAMMING
FORM
®
Principal changes between the VISTA-20SE and
the former VISTA-20 are indicated by margin lines.
VISTA-20PRV4 8/97 (See Instructions N7526V4)
www.PDF-Zoo.com
firealarmresources.com

– 2 –
Local programming requires the use of a 2-line Alpha keypad connected to
partition 1 keypad terminals on the control.
NOTE: For UL installations, the system may be configured as a single partition only.
Field Function Programmed Values [ ] = Default Value
SYSTEM SETUP (*20–*29)
*20 INSTALLER CODE | | | [4 1 1 2]
Enter 4 digits, 0–9
*21 QUICK ARM ENABLE [0]
Part. 1†Part.2†0 = no; 1 = yes
*22 RF SYSTEM [0]
0 = none; 1 = 5800 (5881/5882)
*23 FORCED BYPASS [0] [0]
Part. 1†Part. 2†0 = none; 1 = bypass open zones
“0”. for UL installations.
*24 RF HOUSE ID CODE | [0][0]
00 = disable all wireless keypad usage; 01–31 = using 5827
keypad; Partition 2 RF House ID = Partition 1 House ID +1
*25 WIRED ZONE EXPANSION †[0]
0 = none; 1 = 4219; 2 = 4229; 3 = 4204
*26 CHIME BY ZONE †[0]
0 = no; 1 = yes (program zones to chime on zone list 3)
*27 X–10 HOUSE CODE [0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 =
J, #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P
*28 PHONE MODULE ACCESS CODE | [00]
(Partition 1 only) 1st digit: enter 1–9; 2nd digit: enter # + 11 for "*
", or # + 12 for "#". Entering 0 for either digit disables code.
*29 OUTPUT TO LONG RANGE RADIO [0]
0 = disable; enable = Trouble code 1–9, B (# +11), C (# + 12), D
(# + 13), E (# + 14), or F (# + 15). The 2nd digit of Trouble Dialer
Report is automatically entered from field * 60. “0” for UL
installations.
ZONE SOUNDS AND TIMING (*31–*39)
*31 SINGLE ALARM SOUNDING/ZONE † [0]
1 = yes; 0 = no; “0” for UL installations.
*32 FIRE SOUNDER TIMEOUT †[0]
0 = timeout; 1 = no timeout
*33 ALARM BELL TIMEOUT †[1]
0 = none; 1=4 min; 2=8 min; 3=12 min; 4 = 16 min; “1” (4 min.)
minimum for UL.
*34 EXIT DELAY | | [70] [70]
Part. 1†Part. 2†00-99 = exit delay time for each partition
*35 ENTRY DELAY 1 (zone type 01) | | [30] [30]
Part. 1 †Part. 2 †00-99 = entry delay 1 time for each
partition; 20 seconds max. for UL installations
† Entry of a number other than one specified will give unpredictable results.
www.PDF-Zoo.com
firealarmresources.com

– 3 –
*36 ENTRY DELAY 2 (zone type 02) | | [60] [60]
Part. 1 †Part. 2 †00-99 = entry delay 2 time for each
partition; 50 seconds max. for UL installations
*37 AUDIBLE EXIT WARNING [1] [1]
Part. 1 †Part. 2 † 0 = no; 1 = yes
*38 CONFIRMATION OF ARMING DING [0] [0]
Part. 1 †Part. 2 †
0 = no; 1 = yes (wired keypads and RF); 2 = yes, RF only
*39 POWER UP IN PREVIOUS STATE † [1]
0 = no; 1 = yes; “1” for UL installations
DIALER PROGRAMMING (*40–*53)
In fields *40, *41, *42, enter up to the number of digits shown. Do not fill unused spaces. Enter 0–9; #+11 for '*';
#+12 for '#'; #+13 for a pause.
*40 PABX ACCESS CODE | | | | |
Enter 6 digits. If fewer than 6 digits are entered, exit by
pressing * (and press 41, if entering next field). To clear entries
from field, press *40* .
*41 PRIMARY PHONE No. | | | | | | | | | | | | | | |
Enter up to 16 digits; Do not fill unused spaces. If fewer than 16
digits entered, exit by pressing * (and press 42, if entering next
field). To clear entries from field, press * 41* .
*42 SECONDARY PHONE No. | | | | | | | | | | | | | | |
Enter up to 16 digits; Do not fill unused spaces. If fewer than 16
digits entered, exit by pressing * (and press 43, if entering next
field). To clear entries from field, press *42* .
*43 PRIMARY SUBS ACCT # (Part. 1) | | |
*44 SECONDARY SUBS ACCT # (Part. 1) | | |
*45 PRIMARY SUBS ACCT # (Part. 2) | | |
*46 SECONDARY SUBS ACCT # (Part. 2) | | |
NOTE: If using the paging feature, do not enter a
leading 0 in the subscriber account number, and do
not use digits A-F anywhere in the number. Some
paging systems provide voice mail capability, which
is activated by a leading 0 in the message.
For fields *43 - *46:
Enter 0–9; #+11 for B; #+12 for C; #+13
for D; #+14 for E; [#+15 for F]. Enter * as
4th digit, if 3+1 dialer reporting is to be
used. If only 3 digits used, exit by pressing
* (and press next field).
To clear entries from field, press *43*
,*44*, *45*, or *46* .Examples:
For Acct. 1234, enter: 1 | 2 | 3 | 4
For Acct. B234 , enter: #+11| 2 | 3 | 4
For Acct. 123, enter: 1 | 2 | 3 | *
*47 PHONE SYSTEM SELECT †[1]
If Cent. Sta. IS NOT on a WATS line: 0 = Pulse Dial; 1 = Tone
Dial; if Cent. Sta. IS on a WATS line: 2 = Pulse Dial ; 3 = Tone
Dial.
*48 REPORT FORMAT [7] [0]
Primary Secondary
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1= 3+1, 4+1 RADIONICS STANDARD
2= 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
6or undefined = 4+2 ADEMCO EXPRESS
7= ADEMCO CONTACT ID REPORTING
8= 3+1, 4+1 ADEMCO L/S EXPANDED
9= 3+1, 4+1 RADIONICS EXPANDED
† Entry of a number other than one specified will give unpredictable results.
www.PDF-Zoo.com
firealarmresources.com

– 4 –
*49 SPLIT/DUAL REPORTING [0]
0 = Disable (Backup report only)
TO PRIMARY PHONE No. TO SECONDARY PHONE No.
1= Alarms, Restore, Cancel Others
2= All except Open/Close, Test Open/Close, Test
3= Alarms, Restore, Cancel All
4= All except Open/Close, Test All
5= All All
TO PRIMARY PHONE No. TO PAGING No. * (Secondary)
** A 10-digit code is sent to the pager consisting 6= All except Open/Close ** Alarms, Open/Close, Troubles
of a 4-digit subscriber number, a 3-digit event code, 7= All reports ** Alarms, Troubles
and a 3-digit user or zone number. 8= All reports ** Alarms, Open/Close, Troubles
See Installation Instructions for an explanation 9= All except Open/Close ** Alarms, Open/Close for
of the 10-digit code. users 5-25 (users 5-16 or
wireless button zones 10-
25), Troubles
* Can only be used if primary reporting format is Ademco Contact ID.
*50 15 SEC DIALER DELAY (BURG) †[0]
0 = no; 1 = yes; “0” for UL installations
*51 PERIODIC TEST REPORT †[0]
0 = none; 1 = 24 hours; 2 = weekly; 3 = 30 days (Enter Test
Code in field * 64. Reports with Partition 1 subscriber No.)
*52 TEST REPORT OFFSET † [2]
0 = 24 hour; 1 = 6 hours; 2 = 12 hours; 3 = 18 hours (Time to 1st
report from programming or downloading).
*53 SESCOA/RADIONICS SELECT [0]
0 = Radionics (0–9, B–F reporting); 1 = SESCOA (0–9 only
reporting). Select 0 for all other formats.
† Entry of a number other than one specified will give unpredictable results.
*56 ZONE ASSIGNMENT/ALARM REPORT CODES —This field is an interactive mode. Fill in the required
data on the worksheet below (and on next page) and follow the programming procedure in the installation
manual.
ZONES ON CONTROL: See explanation of headings on next page
·
ZONE ZONE ZONE PART'N ALARM RPT CODE INPUT
RESPONSE
DESCRIPTION No. TYPE No. (Hex) TYPE TIME
(Zn) (ZT) (P) (RC) (In) (RT)
Wired Zone 1* 0 1 HW
Wired Zone 2 0 2 HW
Wired Zone 3 0 3 HW
Wired Zone 4 0 4 HW
Wired Zone 5 0 5 HW
Wired Zone 6 0 6 HW
Wired Zone 7 0 7 HW
Wired Zone 8** 0 8 HW
Expansion Module 0 9 0 5 Both ÑÑ
Supervision
Duress 9 2 — — Both ÑÑ
Console Panic (1 & *, or A) 9 5 Both ÑÑ
Console Panic (3 & #, or C) 9 6 Both ÑÑ
Console Panic (*& #, or B) 9 9 Both ÑÑ
*Zone 1 can be used as a 2-wire Fire zone. **Zone 8 can be used as a Glassbreak zone.
www.PDF-Zoo.com
firealarmresources.com

– 5 –
EXPANSION ZONES: Assign zone numbers (Zn) 10–17 to 4219/4229 Auxiliary Wired Loops A–H, if used. ENTER FOR
RF zones can use zone numbers (Zn) 10–31 [RF ONLY [
ZONE ZONE ZONE PART'N ALARM RPT CODE INPUT LEARNED
DESCRIPTION No. TYPE No. (Hex) TYPEÊÊÊÊRF INPUT
(Zn) (ZT) (P) (RC) (In) (L)
4219/4229 Loop A 1st Exp'n Zone 1 0
or RF Zones B 1 1
C12
D13
E14
F15
G16
H17
RF Zones 1 8
19
20
21
22
23
24
25
RF Zones 2 6
27
28
29
30
31
32
33
EXPLANATION OF ZONE ASSIGNMENT TABLE HEADINGS
Zn = ZONE No. Zone Nos. are from 01 to 31, 92, 95, 96, 99. Some are pre-assigned.
With Field *25 set for auxiliary wired loops (4219, or 4229), use Zone Nos. 10–17 for loops A–H.
With Field * 22 set for RF (5800), use Zone Nos. 10-31.
ZT = ZONE TYPE 00 = Not Used
01 = Entry/Exit #1
02 = Entry/Exit #2
03 = Perimeter
04 = Interior Follower
05 = Trouble Day/Alarm Night
06 = 24 Hr Silent
07 = 24 Hr Audible
08 = 24 Hr Aux
09 = Fire
10 = Interior w/Delay
20 = Arm–Stay
21 = Arm–Away
22 = Disarm
23 = No Alarm Response
24 = Silent Burglary
ÊÊDEFAULT VALUES
Zn: 01 02 03 04
ZT: [09] [01] [03] (03)
Zn: 05 06 07 08 99
ZT: [03] [03] [03] [03] [06]
P = PARTITION No. 1 or 2 Default Values for zones 01 – 08 = [1].
RC = ALARM REPORT CODE Two Hex Digits. For each Hex Digit, enter: 00–09 for 0–9, 10 for A, 11 for B,12 for C, 13 for
D, 14 for E, 15 for F. If "00" is entered as the first digit, there will be no report for that zone.
For contact ID reporting, this is enabling code only. Enter any hex digit (other than 00) in
the first pair of boxes. The second pair of boxes is ignored.
In = LOOP INPUT TYPE HW: Hard Wire
AW: Aux Wire (4219 or 4229) Enter 2 for AW: Auxiliary wired
Enter 3 for RF: Supervised RF
Enter 4 for UR: Unsupervised RF
Enter 5 for BR: Button Type RF
Hard wire zone input
types are automatically
assigned.
RT = RESPONSE TIME 0 = 10msec; 1 = 350 msec; 2 = 700 msec. Default Values for zones 01 – 08 = 1 (350 msec)
L = LEARNED RF INPUT Used with 5800 RF Loop Input Devices. Record transmitter input number.
www.PDF-Zoo.com
firealarmresources.com