Adeunis RF sigfox ANALOG PWR User manual

adeunis ®
283 rue Louis Néel - Parc Technologique Pré Roux
38920 CROLLES - France
Tel. : [phone] - Fax : [phone]
www.adeunis.com [email protected]
sigfox ANALOG PWR
Transceiver Analog/Digital Interface
Guide utilisateur / User Guide
Version 2.0.0
Ce Guide utilisateur s’applique à partir des versions logicielles suivantes :
This User Guide applies from the following rmware versions:
Version RTU : V01.01.01
Version APP : V01.03.04

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
44 Page of 86
FR
ENGLISH

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
45 Page of 86
FR
PRODUCTS AND REGULATORY INFORMATION
Document Informa-
tion
Title sigfox ANALOG PWR - User Guide
Sub-title /
Document type User Guide
Version 2.0.0
This document applies to the following products :
Nom Référence Version rmware
sigfox ANALOG PWR 868 ARF8201AA Version RTU : V01.01.01
Version APP : V01.03.04
DISCLAIMER
This document and the use of any information contained therein, is subject to the acceptance of the adeunis®
terms and conditions. They can be downloaded from www.adeunis.com.
adeunis® makes no warranties based on the accuracy or completeness of the contents of this document and
reservestherighttomakechangestospecicationsandproductdescriptionsatanytimewithoutnotice.
adeunis® reserves all rights to this document and the information contained herein. Reproduction, use or disclo-
sure to third parties without express permission is strictly prohibited. Copyright © 2016, adeunis®.
adeunis® is a registered trademark in the EU and other countries.
TECHNICAL SUPPORT
Website
Our website contains a lot of useful information: information on modules and wireless modems, user guides, and
congurationsoftwareandtechnicaldocumentswhichcanbeaccessed24hoursaday.
E-mail
Ifyouhavetechnicalproblemsorcannotndtherequiredinformationintheprovideddocuments,contactour
Technical Support by e-mail. Use our dedicated e-mail address ([email protected]) rather than any personal e-mail
addressofoursta.Thisensuresthatyourrequestwillbeprocessedassoonaspossible.
Helpful Information when Contacting Technical Support
When contacting Technical Support, please have the following information ready:
• Product type
• Firmware version (for example V1.0)
• A clear description of your question or the problem
• A short description of the application

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
46 Page of 86
FR
EU Declaration of Conformity
WE
adeunis
283 rue LOUIS NEEL
38920 Crolles, France
04.76.92.01.62
www.adeunis.com
Declare that the DoC is issued under our sole responsibility and belongs to the following product:
Apparatus model/Product: ANALOG PWR Sigfox
Type: ARF8201AA
Object of the declaration:
The object of the declaration described above is in conformity with the relevant Union harmonisation
legislation:
Directive 2014/53/UE (RED)
The following harmonised standards and technical specifications have been applied:
Title: Date of standard/specification
EN 300 220-2 V3.1.1 2017/02
EN 301 489-1 V2.1.1 2016/11
EN 301 489-3 V2.1.0 2016/09
EN 62368-1 2014
EN 62311 2008
Otober, 5th,2017 Monnet Emmanuel, Certification Manager

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
47 Page of 86
FR
INTRODUCTION
All rights to this manual are the exclusive property of adeunis®. All rights reserved. Copying this manual (wit-
hout written permission from the owner) via printing, copying, recording or by any other means, translating this
manual (in full or partially) into any other language, including all programming languages, using any electrical,
mechanical, magnetic or optical devices, manually or any by other methods, is prohibited.
adeunis®reservestherighttochangethetechnicalspecicationsorfunctionsofitsproducts,ortoceasemanu-
facturing any of its products, or to cease technical support for one of its products without notice in writing and
urges its customers to make sure that the information they have is valid.
adeunis®congurationsoftwareandprogramsareavailablefreeofchargeinanon-modiableversion.adeu-
nis® can make no guarantees, including guarantees concerning suitability and applicability for a certain type
of application. Under no circumstances can the manufacturer, or the distributor of an adeunis® program, be
held liable for any damage caused by the use of the aforesaid program. Program names, as well as all copyright
relating to programs, are the exclusive property of adeunis®. Any transfer, granting of licences to a third party,
leasing,hire,transport,copying,editing,translation,modicationintoanotherprogramminglanguageorreverse
engineering are prohibited without adeunis®’s prior written authorisation and consent.
Adeunis
283, rue Louis Néel
38920 Crolles
France
Téléphone [phone]
Fax [phone]
DISCLAIMER
This document and the use of any information contained therein, is subject to the acceptance of the adeunis®
terms and conditions. They can be downloaded from www.adeunis.com.
adeunis® makes no warranties based on the accuracy or completeness of the contents of this document and
reservestherighttomakechangestospecicationsandproductdescriptionsatanytimewithoutnotice.
adeunis® reserves all rights to this document and the information contained herein. Reproduction, use or disclo-
sure to third parties without express permission is strictly prohibited. Copyright © 2016, adeunis®.
adeunis® is a registered trademark in the EU and other countries.
TECHNICAL SUPPORT
Website
Our website contains a lot of useful information: information on modules and wireless modems, user guides, and
congurationsoftwareandtechnicaldocumentswhichcanbeaccessed24hoursaday.
E-mail
Ifyouhavetechnicalproblemsorcannotndtherequiredinformationintheprovideddocuments,contactour
Technical Support by e-mail. Use our dedicated e-mail address ([email protected]) rather than any personal e-mail
addressofoursta.Thisensuresthatyourrequestwillbeprocessedassoonaspossible.
Helpful Information when Contacting Technical Support
When contacting Technical Support, please have the following information ready:
• Product type
• Firmware version (for example V1.0)
• A clear description of your question or the problem
• A short description of the application

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
48 Page of 86
FR
ENVIRONMENTAL RECOMMENDATIONS
Allsuperuouspackagingmaterialshavebeeneliminated.Wehavedoneeverythingpossibletomakeiteasyto
separatethepackagingintothreetypesofmaterials:cardboard(box),expandedpolystyrene(llermaterial)
and polyethylene (packets, foam protective sheets). Your device is composed of materials that can be recycled
and reused if it is dismantled by a specialist company. Please observe local regulations concerning the manner in
which waste packaging material, used batteries and your obsolete equipment are disposed of.
WARNINGS
Valid for products indicated in the declaration of conformity
Read the instructions in the manual.
The safety of this product is only guaranteed when it is used in accordance with its purpose. Maintenance
shouldonlybecarriedoutbyqualiedpersons.
Please note: Do not install the equipment close to a heat source or in damp conditions.
Please note: When the equipment is open, do not carry out any operations other than the ones set out in this
document.
Please note: Do not open the product as there is a risk of electrical shock.
 Pleasenote:Foryourownsafety,youmustensurethattheequipmentisswitchedobeforecarryingout
any work on it.
Please note: For your own safety, the power supply circuit must be SELV (Safety Extra Low Voltage) and
must be from limited power sources.
Please note: When the aerial is installed outside, it is essential to connect the cable screen to the buil-
ding’s earth. We recommend using lightning protection. The protection kit chosen must permit the coaxial cable
tobeearthed(eg:coaxiallightningarresterwithearthing ofthecableatdierentplacesontheaerialatthe
base of pylons and at the entrance, or just before entering the premises).
The product must be equipped with a switching mechanism so that the power can be cut. This must be close to
the equipment. Any electrical connection of the product must be equipped with a protection device against vol-
tage spikes and short-circuits.

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
49 Page of 86
FR
RECOMMANDATIONS REGARDING USE
• Before using the system, check that the power supply voltage shown in the user manual corresponds to your
supply. If it doesn’t, please consult your supplier.
• Placethedeviceagainstaat,rmandstablesurface.
•
Thedevicemustbeinstalledinalocationthatissucientlyventilatedsothatthereisnoriskofinternalhea-
ting and it must not be covered with objects such as newspapers, cloths, curtains, etc.
• The device’s aerial must be free and at least 10 cm away from any conducting material.
• The device must never be exposed to heat sources such as heating equipment.
• Donotplacethedeviceclosetoobjectswithnakedamessuchaslitcandles,blowtorches,etc.
• The device must not be exposed to harsh chemical agents or solvents likely to damage the plastic or corrode
the metal parts.
DISPOSAL OF WASTE BY USERS IN PRIVATE HOUSEHOLDS WITHIN THE EURO-
PEAN UNION
This symbol on the product or on its packaging indicates that this product must not be disposed of with your
other household waste. Instead, it is your responsibility to dispose of your waste by taking it to a collection point
designated for the recycling of electrical and electronic appliances. Separate collection and recycling of your waste
at the time of disposal will contribute to conserving natural resources and guarantee recycling that respects the
environment and human health. For further information concerning your nearest recycling centre, please contact
yournearestlocalauthority/townhalloces,yourhouseholdwastecollectioncompanyortheshopwhereyou
bought the product
This symbol on the devode or its packaging means the use of a DC voltage.
Warning: If the charger is used with any other batteries or products whatsoever, there is a risk of an ex-
plosion. After use, the batteries must be disposed of at an appropriate recycling centre. They must not be thrown
away to degrade in the environment. When batteries are replaced, the device must be corectly implemented.
Warning for Switzerland : the annex 4.10 of SR 814.013 Standad must be applied for batteries.

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
50 Page of 86
FR
1.1. General description
1. PRODUCT PRESENTATION
IMPORTANT NOTE: The sigfox ANALOG PWR can only be started with a magnet.
Description :
• The adeunis® sigfox ANALOG PWR is a ready-to-use radio transmitter enabling any type of 0-10V or 4-20mA
sensor to be converted into a wireless communicating sensor.
• This product meets the needs of users who need to remotely monitor data of any kind (temperature, pressure,
level, humidity, CO², speed, brightness, opening, etc.)
• The use of the sigfox protocol allows you to integrate the sigfox ANALOG PWR into any network that is already
deployed.
• Two sensors can be supported by a single sigfox ANALOG PWR transmitter.
• The product transmits the data from the sensors either periodically or in an event-related way based on top or
bottom thresholds or on detection of a change of state on its digital inputs.
•Thecongurationofthetransmitterisaccessiblebytheuserviaamicro-USBport,allowinginparticulara
choice of modes of transmission, periodicity or type of interface (0-10V or 4-20mA).
• The sigfox ANALOG PWR is powered by an external power supply.
IMPORTANT NOTE : the sigfox ANALOG PWR can transmit measurements from the sensors but does not feed
them (except the digital version).
Composition of the package
The product is supplied in a cardboard box containing the following items:
top casing, electronic card, casing base plate,
cable gland, 3 gland seals, 2 CBLZ 2.2 x 19mm screws, 2 Fischer SX4 plugs
107
90 27
49,50
2 holes for passing
collars through
Rail-DIN unlocking
lever
4 fastening holes
Cables outlet
packing gland
Casing base
Casing base detail
Antenna

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
51 Page of 86
FR
107
90
27
49,50
107
90
27
49,50
107
90 27
49,50
1.2. Dimensions
Values in millimetres
1.3. Electronic card
Screw terminals for
connecting sensors
USBportforproductcongu-
ration
RF module
sigfox protocol
Internal antenna
Internal battery

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
52 Page of 86
FR
1.4. Technical Specications
1.4.1 General characteristics
Parameters Value
Power supply 5-36V DC
Maximal power 90mA
Working temperature -25°C / +70°C
Dimensions 105 x 50 x 27mm
Weight 49g
Casing IP 67
Radio standards EN 300-220, EN 301-489, EN 60950
Radio standards EN 300-220, EN 301-489, EN 60950
1.4.2 Physical interface characteristics
1.4.2.01 4-20mA interfaces
The schematic diagram of the 4-20mA interfaces is the following:
Absolute maximum values Units
Minimum input current 0 mA
Maximum input current 30 mA
Caractéristiques électriques Unité
Minimum input current 4 mA
Maximum input current 20 mA
Equivalent input impedance 99,8 (+/-0,1%) Ω
12-bit analog input resolution
Values higher than the absolute maxima would damage the product.

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
53 Page of 86
FR
1.4.2.02 Interfaces 0-10V
The schematic diagram of the 0-10V interfaces is the following:
Absolute maximum values Units
Minimum input voltage 0 V
Maximum input voltage 15 V
Electrical characteristics Units
Minimum input voltage 0 V
Maximum input voltage 10 V
Equivalent input impedance 337,3 (+/-0,2%) kΩ
12-bit analog input resolution
Values higher than the absolute maxima would damage the product.
1.4.2.03 Digital interfaces
The schematic diagram of the digital interfaces is the following:
Absolute maximum values Units
Minimum input voltage - 0,7 V
Maximum input voltage +50 V

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
54 Page of 86
FR
Electrical characteristics Units
Minimum input voltage 0 V
Maximum input voltage 24 V
Equivalent input resistance 500 kΩ
Input frequency 10 Hz
High input level current consumption 0 µA
Low input level current consumption 6 µA
1.4.2.04 Power supply
External power supply requirement Unit
Minimum input voltage 6 V
Maximum input voltage +24 V
Minimum power required 2,5 W
Values higher than the absolute maxima would damage the product.
1.4.3 Sensor compatibility
Examples of sensors tested by adeunis® (non-exhaustive list)
Type Name Type Applications
4-20mA EE80 E+E Electronik CO2, temperature, relative
humidity Technical management of buildings, air qua-
lity, ventilation, etc.
4-20mA PR791F
Asco Instrument Pressure Industrial processes, static and dynamic
measurements, etc.
0-10V PF211
Mitchell instruments Relative humidity Hvac and regulation of ambient conditions
0-10V ADT 23-110
MSR Electronic Nitrogen dioxide NO2 Detecting nitrogen dioxide in underground
garages, tunnels, shel-
ters, industrial areas,
etc.
TOR RBWF-LF
S+S Regeltechnik Brightness, movement, presence Technical management of buildings, presence
sensing for lighting
control, ventilation,
etc.

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
55 Page of 86
FR
2. PRODUCT OPERATION
2.1. Global Operation
Important: adeunis®usethemostsignicantbyterstformat.
The product has several operating modes:
2.1.1 PARK mode
The product is delivered in PARK mode, it is in standby mode and its consumption is minimal. To switch the pro-
duct out of the Park* Mode pass a magnet across it for a duration higher than 6 seconds. The green LED illumi-
natestoindicatethedetectionofthemagnetandthenashesquicklyduringtheproductstartingphase.
Thedevicethensendsitscongurationanddataframes(seeparagraph4.1).
2.1.2 COMMAND mode
Thismodeallowstheusertoconguretheregistersoftheproduct.
To enter this mode, connect a cable to the micro-USB port of the product and enter the command mode by an AT
command (see paragraph 3).
2.1.3 OPERATING mode
There are two possible modes of operation:
• TEST mode:
This mode allows the user to perform tests of the product more quickly by reducing the time scales of production
mode and modifying the behaviour of the LEDs (see paragraph 2.2.5).
• PRODUCTION mode:
Thismodeallowstheusertooperatetheproductinitsnaluse.Itshouldallowamaximumofautonomytothe
product.
To switch from one mode to the other the user changes the value of a register
PRODUCTION MODE
TEST MODE
COMMAND MODECOMMAND MODE
The return to the
production mode
is done by the ATO
command or by dis-
connecting the USB
cable
PARK MODE
OPERATING MODE
COMMAND MODE
Command sending
by serial link
Presence of a magnet
on the product >6s

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
56 Page of 86
FR
2.2. Application operation
2.2.1 Periodic transmission
The product allows the measurement and the periodic transmission of the values of the sensors according to the
following diagram:
The settings associated with this mode of operation are:
• the transmission period (register 301).
• the presence and type of external sensor (registers 320 and 322).
A complete list of the registers can be found in paragraph 3.4.
Eg:
Registre Value encoding Valeur Result
S301 Decimal 6 Periodic mode with a
period of 6x10min = 60
minutes
S320 Hexadecimal 0x02 ChannelAconguredfora
sensor 4-20mA
S322 Hexadecimal 0x01 ChannelBconguredfora
sensor 0-10V
Product in standby
Measurement input A
(if enabled)
Measurement input B
(if enabled)
Send frame 0x40
Period
reached?
YES
No

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
57 Page of 86
FR
2.2.2 Transmission on exceeding of the threshold
The product allows detection threshold overrun (upper and lower) for each sensor according to the following dia-
gram:
Consequently the product sends a frame of data at the threshold overrun and also during a return to normal.
Send frame 0x42
Period
reached?
Value < low
threshold +
hystérésis
?
Value <high
threshold -
hysteresis
?
Value < low
threshold
Value >
high thres-
hold
Low
alert not
enabled?
High
alert not
enabled?
Low alarm enablingHigh alarm disabling Low alarm enablingHigh alarm enabling
Measurement input B
(if enabled)
Measurement input A
(if enabled)
Product in standby
NO NO
NO
NO
NONO
NO
YES
YES
YES
YES YES
YES
YES

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
58 Page of 86
FR
Explanation of thresholds and hysteresis:
Themonitoringperiodbythesensorsisxedat10minutes(tochangethisvalue,contacttheTechnicalSupport
Department).
The settings associated with this mode of operation are:
• The transmission periodicity (zero in this usage situation) (register 301).
• The presence and type of external sensor (registers 320 and 322).
• Thecongurationoftheevents(registers321and323).
• The high alarm threshold channel A (register 324).
• The high alarm hysteresis channel A (register 325).
• The low alarm threshold channel A (register 326).
• The low alarm hysteresis channel A (register 327).
• The high alarm threshold channel B (register 328).
• The high alarm hysteresis channel B (register 329).
• The low alarm threshold channel B (register 330).
• The low alarm hysteresis channel B (register 331).
A complete list of the registers can be found in paragraph 3.4.
E.g.:
Register Value encoding Value Result
S301 Decimal 0 Event mode
S320 Hexadecimal 0x02 ChannelAconguredforasensor4-20mA
S322 Hexadecimal 0x01 ChannelBconguredforasensor0-10V
S321 Hexadecimal 0x03 On channel A:
Detection of high and low thresholds
Detection of event on disabled digital input
No waiting period
S323 Hexadecimal 0x02 On channel B:
Detection of high thresholds
Detection of event on disabled digital input
No waiting period
S324 Decimal 1 200 000 The value of the high threshold of channel A is:
1 200 000x10=12 000 000nA so 12mA
high threshold
Low threshold
High threshold - high threshold hysteresis
Low threshold + low threshold hysteresis
Sensor value
High alarm enabling High alarm disabling
Low alarm enabling Low alarm disabling

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
59 Page of 86
FR
S325 Decimal 100 000 The value of the hysteresis of the high thres-
hold of channel A is: 100 000x10=1 000 000nA
so 1mA
S326 Decimal 600 000 The value of the low threshold of channel A is:
600 000x10=6 000 000nA so 6mA
S327 Decimal 100 000 The value of the hysteresis of the low threshold
of channel A is: 100 000x10=1 000 000nA soit
1mA
S328 Decimal 8 000 000 LThe value of the high threshold of channel B is:
8 000 000µV so 8V
S329 Decimal 1 000 000 The value of the hysteresis of the high thres-
hold of channel B is: 1 000 000µV so 1V
S330 Decimal 3 000 000 The value of the low threshold of channel B is:
3 000 000µV so 3V
S331 Decimal 1 000 000 The value of the hysteresis of the low threshold
of channel A is: 1 000 000µV so 1V
2.2.3 Transmission on event of digital input
The product allows the measurement and the transmission of the values of the sensors following an event on a
digital input according to the following diagram:
Thistriggeringcanbeontherisingedge,fallingedgeorboth.Acongurabledebounceispresentoneverydigital
input.
Input TOR1 is associated with channel A and input TOR2 with channel B.
The settings associated with this mode of operation are:
• The transmission periodicity (zero in this usage situation) (register 301)
• The presence and type of external sensor (registers 320 and 322).
• Thecongurationoftheevents(registers321and323).
A complete list of the registers can be found in paragraph 3.4.
Product in standby
Measurement input A
(if enabled)
Measurement input B
(if enabled)
Send frame 0x42
Change
on digital
input?
Oui
Non

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
60 Page of 86
FR
Eg:
Register Value encoding Value Result
S301 Decimal 0 Event mode
S320 Hexadecimal 0x02 ChannelAconguredforasensor4-20mA
S322 Hexadecimal 0x01 ChannelBconguredforasensor0-10V
S321 Hexadecimal 0x1C Channel A:
No threshold detection
Event detection on digital input on rising and
falling edges
• Waiting* period of 10ms
S323 Hexadecimal 0x18 Channel B:
No threshold detection
Event detection on digital input on rising
edge only
• Waiting* period of 10ms
* Waiting* period (or debounce time): minimum time for taking into account a change of state. For example if this
period is 10ms, all pulses (high or low level) whose duration is less than 10ms will not be taken into account. This
technique prevents rebounce on a change of state.
2.2.4 Transmission of a daily Keep Alive frame
In the event mode (threshold or digital), it is possible that the product would never send data frames. So to be
sure that it is working properly a Keep Alive frame is transmitted regularly according to the following diagram:
In periodic mode there is no Keep Alive frame transmission.
The settings associated with this mode of operation are:
• The setting of the period of transmission of the Keep Alive frame (once per hour to once per day) (register 300).
A complete list of the registers can be found in paragraph 3.4.
E.g.:
Register Value encoding Value Result
S300 Decimal 72 The Keep Alive frame is sent every:
72x10=720min i.e. 12h (or twice per day)
Product in standby
Send frame 0x30
Period
reached?
Yes
No

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
61 Page of 86
FR
2.2.5 TEST Mode
This mode allows the user to perform tests of the product more quickly by reducing the time scales of the produc-
tion mode and modifying the behaviour of the LEDs.
It is obtained by positioning register S306 at the value 2 in the COMMAND mode. Once out of the command
mode,theproductreturnstothepreviouslydenedapplicationbehaviourbutwiththefollowingchanges:
- register S300: the periodicity of the Keep Alive frame is expressed in groups of twenty seconds instead
of tens of minutes. Hence in test mode when register 300 = 144, the Keep Alive frame is no longer sent every
144x10min=1440 minutes or 24h but every 144x20s=2880 seconds or 48 minutes.
- register S301: the periodicity of the sending of data (periodic mode) is expressed in groups of twenty
seconds instead of tens of minutes. Hence in test mode when register 301 = 1, the data frame is no longer sent
every 10min but every 20 seconds.
- In the event mode with transmission on threshold overrun the monitoring period of inspection by the
sensors, normally 10 minutes is now, in TEST mode, set to 100 seconds.
 -TheLEDSalsohavedierentbehaviour,allowingavisualfeedbacktotheuserintheeventoftransmis-
sion and reception of frames (see paragraph 2.3 for more details).
A complete list of the registers can be found in paragraph 3.4.
E.g.:
Register Value encoding Value Result
S306 Decimal 2 The product is in TEST mode
S300 Decimal 72 The Keep Alive frame is sent every:
72x20=1440s = 24 minutes
S301 Decimal 6 Periodic mode with a period of 6x20 =
120s = 2 minutes
2.3. Operation of the LEDs
Mode LED red state LED green state
Transmission of frame (TEST mode
only) ON during the transmission cycle
Reception of frame (TEST mode
only) ON during the reception of a down- link frame
Product in Park mode OFF OFF
Magnet detection process (1 to 6
seconds) OFF ON from detection of the magnet up to a maximum of 1 second
Product start (after detection of
the magnet) OFF Rapidashing6cycles,100msON / 100 ms OFF
Switching to the Command mode Continuously lit Continuously lit
Battery level low Flashing (0.5s ON every 60s)
Product faulty (return to factory) Fixed ON
Product in production mode (TEST
mode only) 50ms ON / 50 s OFF 50ms ON / 50 s OFF (just before the red LED)
Product in REPLI mode Flashing (100ms ON / 100ms OFF) x
2 every 5s

EN
sigfox ANALOG PWR - Guide utilisateur / User guide version V2.0.0
62 Page of 86
FR
3. DEVICE CONFIGURATION
ThedevicecanbeconguredusingtheUSBconnector.Thisconnectionallowsyoutocommunicatewiththedevice
via a virtual com port and to transmit AT commands in order to modify the parameters of the device.
WARNING : the USB connection does not supply power to the product, it induces a consumption of the product as
long as the one is connected. It is therefore important not to leave the product connected too long.
3.1. Connecting the device to a computer
Connect the product to the USB input of a computer. The product has a Type B micro USB connector.
During connection, the device must be recognised by the computer as a Virtual Com Port (VCP) device.
Using Windows: Verication that the device has been recognised to be functioning properly can be obtained by
consulting the device manager. You should see the USB series device with a corresponding COM port number appear
during connection.
If you are not able to see a device of this type, you must install the USB driver for this device, available to download from our website:
https://www.adeunis.com/produit/analog/
Select:
• Driver USB-STM32_x64, if your computer is a 64 bits system
• Driver USB-STM32, if your computer is a32 bits system