ADIMLab Gantry User manual

ADIMLab-gantry
Assembly specifications
Version V 1.3.2

2
ADIMLab-gantry
Assembly steps
1.Install the frame
The whole machine is basically installed before delivery,
divided into the gantry bracket, the base components, and the
3D printer control box three modules, we only require three
modules can be assembled simply. After assembly, the finished
product is as follows:

3
1.1 Install the gantry bracket to the base components.
(1) Place two M5 * 25 screws to secure the gantry to the base
flat. Pay attention to the reference of the installation of the
picture, do not install opposite.

4

5
(2)Install the Z-axis limit switch mounting plate to the left
side of the machine.

6
(3) Install the Z-axis fixed plate to the right side of the
machine.
(4) Install filament bracket

7
(5) Install filament detector module.

8
2.Wiring
1：X-motor 2：Y-motor 31：Z1-motor
32：Z2-motor 4：Extruder ①：X-Endstop
②：Y-Endstop ③：Z-Endstop ○4
Extruder wiring：（4：Extruder）
：4 : Hotbed
⑤：filament detector

9
filament detector wiring（⑤：filament detector）
3.Machine test run
3.1 Select voltage：
(1) Crate provides two kinds of voltage options, namely 110V
and 220V,the default voltage of 220V, before connecting the
power source, selectthe correct voltage. (Please confirm the
correct and then turn on thepower supply, otherwise the power
Will be broken.

10
3.2Test of return to zero：
(1) Control box left power button

11
(2) “Info screen”click button，select“Prepare”，click ok：
(3)Select“Auto home”in Submenu，click ok：
Normally, the three axes will return to the position of the
original point,as follows.

12
3.3Test heating
(1) “Info screen”click button，Select“Prepare”,click ok：
(2) Select“Preheat PLA”in Submenu，click ok：

13
(3) Select“Preheat PLA”in Submenu，click ok：
If the two temperatures in following picture are on the rise,
the heating is normal.
If“Auto home”and“Preheaet PLA”normal，It mean your 3D printer
is already connected.

14
4.Machine levelling
4.1Adjust the level of the X-axis bar.：
(1) “Info screen”click button，Select“Prepare”,click ok：
(2) Select“X Height adjustment”，click ok：
(3)Zaxis automatic raise 30mm，Use a solid glue stick or print
to measure the distance between the ends of the X-axis guide
and the base.

15
(5) Adjust the height of the X-axis guide by rotating the Z-axis
blue coupling so that the metal parts at both ends of the X-axis

16
guide are just enough to touch the glue stick or print.
4.2Hodbed Leveling：
(1) “Info screen”Select“Prepare”,click ok：
(2) Select“Manual Bed Leveling”in Submenu，click ok：
(3) Home to the original point，Extruder moves to the first
adjustment point in the lower left corner of the hot bed.

17
(3)Adjust hand screw nut under the platform，Make the
nozzletouch the hot bed:
(4)Click knob，ExtruderMove to the second adjustment point，
Adjust hand screw nut under the platform，Make the nozzle just
touch the hot bed:

18
(5) Click knob，Extruder move to the third adjustment point，
Adjust hand screw nut under the platform，Make the nozzle just
touch the hot bed:
(6) Click knob，Extruder move to the fourth adjustment point，
Adjust hand screw nut under the platform，Make the nozzle just
touch the hot bed:

19
(7) Click knob，Extruder move to the middle of the hodbed，
check the distance between the nozzle and the hot bed.If nozzle
just touch the hotbed，It mean adjust succeed，Select“Back”
in the Lcd display：

20
(8) If the distance between the nozzle and the hot bed is too high or too
low，select“Next Point”repeat(4)-(8)operating
5.Machine printing test
（1）Insert the filament.：