ADLINK Technology NuPRO-761 User manual

NuPRO-761
Full-Size Single BoardComputer
User sGuide
6007002N761A0
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Copyright 2003 ADLINKTechnologyInc.
AllRightsReserved.
ManualRev. 1.00: September22,2003
PartNumber:
Theinformationinthisdocumentissubjecttochangewithoutpriornoticeinorder
toimprovereliability,designandfunction anddoesnotrepresentacommitmenton
thepartofthemanufacturer.
Innoeventwillthemanufacturerbeliablefor direct,indirect,special,incidental, or
consequentialdamagesarisingoutoftheuseorinabilitytousetheproductor
documentation, evenifadvisedof thepossibilityofsuch damages.
Thisdocumentcontainsproprietaryinformationprotectedbycopyrightlaws.All
rightsarereserved.Nopartof thismanualmaybereproducedbyanymechanical,
electronic,orothermeansinanyformwithoutpriorwrittenpermissionofthe
manufacturer.
Trademarks
NuPROisaregisteredtrademarkofADLINKTechnologyInc.Otherproduct
namesmentionedhereinareusedforidentificationpurposesonlyandmaybe
trademarksand/orregisteredtrademarksoftheirrespectivecompanies.
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

i
Getting service from ADLINK
•CustomerSatisfaction isthemostimportantpriorityfor ADLINKTech Inc.If
you needany helporservice, pleasecontactus.
ADLINK TechnologyInc.
Web Site http://www.adlinktech.com
Sales& Service
[e-mail]
NuDAQ + USBDAQ [e-mail]
Automation [e-mail]
NuIPC [e-mail]
Technical
Support
NuPRO /EBC [e-mail]
TEL [phone]FAX[phone]
Address 9F, No.166,Jian Yi Road, Chungho City,Taipei, 235Taiwan.
•Pleaseemailor FAXus ofyourdetailedinformation foraprompt,satisfactory
and constantservice.
DetailedCompanyInformation
Company/Organization
Contact Person
E-mailAddress
Address
Country
TEL FAX
Web Site
Questions
ProductModel
Environment toUse
OS:
ComputerBrand:
M/B: CPU:
Chipset:BIOS:
Video Card:
NetworkInterfaceCard:
Other:
Detail Description
Suggestionsto ADLINK
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

ii
CONTENTS
SECTION 1 INTRODUCTION 1
1.1 Unpacking NuPRO-761 Series1
1.2 Description 3
1.3 Features3
1.3.1 Hardware Monitoring 4
1.3.2 I/OShield Connector 4
1.3.3 NuPRO-761 SeriesOverview4
1.3.4 System Block Diagram5
1.4 Specifications6
SECTION 2 INSTALLATIONS 8
2.1 System Installation 8
2.1.1 CPU Installation 8
2.1.2 Heat SinkInstallation 9
2.1.3 Memory Module Installation 10
2.1.4 Setting Jumper and DIP Switches11
2.2 Board Layout 12
2.3 JumperSetting 13
2.4 ConnectorsDescription 16
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

iii
CONTENTS
SECTION 3 AWARD BIOS SETUP 31
3.1 BIOSInstructions31
3.2 Main Menu 32
3.3 Standard CMOSFeatures 34
3.4 IDE Adapters 36
3.5 Advanced BIOSFeatures38
3.6 Advanced Chipset Features42
3.7 Integrated Peripherals 47
3.8 Power Management Setup 52
3.9 PnP/PCIConfigurations 57
3.10 PC HealthStatus 59
3.11 Frequency/Voltage Control61
3.12 Load Fail-SafeDefault 62
3.13 Load Optimized Defaults62
3.14 Supervisor/User Password Setting 63
3.15 Exit Selecting 64
Warranty Policy65
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

iv
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

1
INTRODUCTION
1.1 Unpacking NuPRO-761 Series
1. Takeout the NuPRO-761 series unitfromthe carton box, check if the unit
isproperly secure inthe plasticbag.
2. Check thecontentsofthe carton box:
¿Single Board Computer ¿InstallationGuide
¿ATA-66/100 HDDribbon cable ¿Floppy ribbon cable
¿K/B& M/SY Type cable ¿DriverCD
S
ECTION
1
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
2
¿K/B-M/Sextend toBPcable ¿ATXpower controlcable
(6-pinsto 5-pins)(4-pinsto 5-pins)
¿COM2 ribbon cable¿Printer ribbon cable
(14-pinsto Dual9-pinsD-Sub) (26-pinsto 25-pinsD-Sub)
3. Optionalcable:
¿USB2.0 cable ¿Audio cable
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
3
1.2 Description
The NuPRO-761 Seriesall-in-one single board computer isoptimized for
socket 370 FC-PGAprocessor, supporting 100MHz and 133 MHz FrontSide
Bus,the memory can accommodate isup to 2GB DDR SDRAM. Thisboard
isbased on the VIA®8623 (CLE266) chipset and is fully designed forharsh
industrial environment.TheNuPRO-761series is with integrated LCD/VGA,
AC97 Audiofunction and on board single 10/100 MbpsEthernet. Theyare
forCTI and high-end applications.
The other I/Ofunction include two serialports, one parallelport, two IDE
interface,one FDCinterface,fourUSB2.0 ports,WatchDog Timer,DOC and
PS/2 Keyboard &Mouse.
1.3 Features
¿Socket 370 for Intel®Celeron™/Pentium®!!!/ VIA®C3 processor
¿VIA®VT8623 +VT8235 AGPset (CLE266)
¿Support2GBDDR SDRAM (Max.) Memory
¿Front SideBusFrequency: 100/133 MHz
¿VIA®VT8623 chipintegrated LVDS/TFTpanelinterface
¿Single 10/100 MbpsEthernet interface using Realtek®RTL8100BL chip
¿AC97 Audio Codec
¿2xCOM ports, 4 xUSB2.0
¿Software programmable watchdog timer
¿Hardware Monitoring
¿SSD (DOC) socket
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
4
1.3.1 Hardware Monitoring
Hardware monitoring allows you to monitor variousaspectsof your systems
operationsand status. The featuresinclude CPU temperature, voltage and
RPM offan.
1.3.2 I/OShield Connector
The SBC isequipped with an I/O bracket.Please use the appropriate I/O
shield (figure 1).
NuPRO-761 Series
COM1
VGALAN
KB
MS
Figure 1: I/O bracketlayout
1.3.3 NuPRO-761 Series Overview
Function /Model NuPRO-761
¿ChipsetVIA®VT8623 (CLE266)
¿LCD Function ž
¿VGA Function ž
¿Ethernet Function ž
¿AudioFunction ž
¿TwoEIDE Interface ž
¿OneFloppyInterface ž
¿TwoSerial, One Parallel ž
¿Four USB2.0 ports ž
¿Solid StateDiskSocket ž
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
5
1.3.4 System Block Diagram
P!!! Socket370-pins
Clock
VRM
DATACTRLADDR
VIA
VT8623
VIA
VT8235
DDRSDRAM
100/133X2
DVI/ CRT
Device
Realtek
RTL8100BL
10/100T-Base
SuperI/O
W83627HF
ATA100
USB2.0
IDE Primary
IDESecondary
USBPort1/2
USBPort3/4
Keyboard
Mouse
COMPort
LPT Port
Floppy
iTEBridge
IT8888F
ISABUS
PCIBUS
P
I
C
M
G
S
L
O
T
AC97
Audio
Codec
100/133MHZFSB
LVDS
or
VGA
Figure 2: SystemBlockDiagram
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
6
1.4 Specifications
NuPRO-761 Series:
¿Processor:
-Socket 370 Processor, for Intel®Celeron™/ Pentium®!!!/ VIA®C3™
Processor
¿Chipset:
-VIA®VT8623 AGPset
¿Front Side Bus:
-66/100/133 MHz
¿DRAM Module:
-184pinsDIMM x2for200/266 MHz Memory
-Support DDR SDRAMup to 2GB
¿LCD/VGAFunction:
-VIA®VT8623 integrated Video Acceleratorscontroller
-Support LVDS /TFT panel interface
¿LAN Function:
-Realtek®RTL8100BL Ethernet controller
-For 10/100Base-TXEthernet
¿OnboardI/O:
-On-ChipI/Ointegrated withK/B, Mouse, FDD, Paralleland Serial
controllers
¿OnboardPCI/IDE:
-VIA®VT8235 Southbridge Controller
-PCI rev2.2Compliant
-ACPI Compliant Power Management
-PCI BusIDEPortwith PIO/ ATA-100 x2 (Upto 4Devices)
¿I/OConnector:
-9-pinsD-Sub COM1 connector
-RJ-45 Ethernet connector
-15-pinsD-Sub VGAconnector
-PS/2 Mouse and PS/2styleKeyboard
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Introduction
7
¿USB2.0 Ports:
-4 x USB2.0ports(pin-header)
¿BIOS:
-Award Plug & Play BIOS
¿ExtendedFunction:
-Hardware Monitoring function by Winbond®ASIC
-IrDA bypin-header
¿Form Factor:
-13.3”x4.8”(338 x122mm)
¿Weight:
-0.84lb (380g) --- NuPRO-761
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

8
INSTALLATIONS
2.1 System Installation
2.1.1 CPU Installation
Carefully followthe stepsbelowin order to install the CPU:
1. Check and confirmthat the jumpersare correctly set for the CPUyou
are going to install(figure3).
2. Liftthe releasing leverof the Socket 370.
3. Align the pinsoftheCPU againstthe pinholesof the Socket 370. Be
sure to pay attention tothe orientation of the CPU.
Figure 3: CPU Socket
4. Push down the CPU intothe Socket 370.
5. Push down the release leverand lock itagainst the keyhook.
6. Hook the holeinZIF clipfor theCPU cooling fan onto the notch on the
socket 370.
7. Place the CPU cooling fan atopthe CPUsurface.
8. Push down the opposite side ofthe ZIF clip and hook it.
9. Slide the head of the clipto leftand lockit.
10. Connect the cooling fancabletothesocket as shown below.Becareful
not to place thecable onthe CPU cooling fan.
S
ECTION
2
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
9
Removing a CPU:
1. Beforeremoving theCPU,turn off the NuPRO-761 Seriespower; then
wait for about 20 minutesuntil the heat radiation plate ofthe cooling fan
and the CPU cooldown.
2. To removethe CPU,liftthe releasing leverofthe Socket 370.
Note: The CPU and theheat radiationplateare hot.They may cause
burns.
Toremove theCPU,reverse the installation steps.
2.1.2 Heat SinkInstallation
It ishighly recommended that only NuPRO-761 Heat Sink +Fan (Figure 4),
designed for use inthe chassisbe used -- the use of other heat sinks,
including those boxed with CPUs,mayresultin damage to the NuPRO-761
SBC.
Make sure that good contact ismade between the processorsand the heat
sinks. Insufficientcontact,incorrecttypesofheatsinks,fans, or thermal
compound used or improper amount of thermalcompound applied on the
CPU diecan causethe processorsto overheat,which may crashthe system.
Figure 4: Heat SinkInstallation
Heat Sink& Fan
(ForP3 processor only)
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
10
2.1.3 Memory Module Installation
Figure 5display the notch marksand what they should look like on your
DIMM memory module.
DIMMshave184-pinsand two notches, that willmatch with the onboard
DIMM socket.DIMM modulesare installed by placing thechipfirmly into the
socket at a90-degree angleand pressing straight down (figure 6)untilit fits
tightlyinto the DIMMsocket.
Figure 5: DIMMMemoryand 184-pinsSocket
Figure 6: Memory Installation
Carefully followthe stepsbelowin order to install the DIMMs:
1. To avoidgenerating staticelectricityand damaging theDIMM,ground
yourselfbytouching agrounded metalsurfaceorusing agroundscrap
before youtouch the DIMM.
2. Do not touch the connector ofthe DIMM.Dirt residuemay causea
malfunction.
3. Hold theDIMM withitsnotch to the front sideofthe NuPRO-761 Series
and insert it completelyinto the socket. ADIMM shouldbe inserted into
the inner socket first. Guiding the holeateach end oftheDIMMover the
retaining post at each end of the DIMMsocket.
4. Ifyou installtwoDIMMs, install the second DIMMusing the same
procedure asabove.
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
11
5. If DIMM doesnot go insmoothly, do not force it. Pullit allthe way out
and try again.
6. Make sure the DIMM isproperlyinstalled and locked by the tabson both
sidesofthe socket.
Removing a DIMM:
To removetheDIMM,useyour fingersor asmallscrewdriver to carefully
pushaway the plastictabsthat secure the DIMM ateach end. Lift itout of
the socket.
Make sure you store theDIMMin an anti-staticbagand must be
populated the same size and manufactory ofmemory modules..
2.1.4 Setting Jumpers and DIP Switches
There are jumpersand DIP-switcheson the systemboard ofthe
NuPRO-761 Series.You can set the jumpersto make the necessary
operations.
Figure 7: Jumper Connector
For any three-pinsjumpers(figure 7), the jumper setting is1-2 when the
jumper connectspin1and 2.The setting is2-3 when pin2and 3are
connected and soon. Yousee anumber “1 “and a “3 “printed onthe
circuitboard to identifythesepins.And also, there isasecond way of
indication –one ofthe linessurrounding jumpersisthick,which indicatespin
NO.1.
To moveajumper fromone position to another,useneedle-nosepliersor
tweezersto pullthepincap off the pinsand moveitto the desired position.
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
12
2.2 Board Layout
Jumper& Connector Location
NuPRO-761 Rev1.0
CN1
CN7
CN8
CN10
CN11
CN12
CN13
CN6
CN4
CN3
CN2
CN14
CN15
CN16
CN17
CN18
CN9
CN19
CN20
CN21
CN22
CN25
BATT1
JP1
JP2
JP3
DIMM1DIMM2
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
13
2.3 Jumper Setting
Tablefor Jumper Location Description:
Use the information inthe following tableto change thejumpers.
Jumpers Functions
JP1 LCD PowerSettingSelect
JP2 COMPortSettingSelect
JP3 Clear CMOSSettingSelect
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com

Installations
14
In order to set up the correct configuration,here isthedescription
about howto set the jumperstoenable/disableorchange functions.All
jumpers location please refer to jumper location diagram.
®LCD Power SettingSelect:JP1
Function JP1
3.3V (Default)1-2
5V 2-3
—Location:
®COMPort Setting Select: JP2 JP2
Function 1-2 3-4 5-6 7-8 9-10 11-12
RS-232 (Default)
OffOffOffOffOffOn
RS-422 On (Term.)
On (Term.)
OffOnOnOff
RS-485 On (Term.)
On (Term.)
OnOffOnOff
—Location:
PDFcreated with FinePrint pdfFactory Pro trialversion www.pdffactory.com