Admag TI Series User manual

User’s
Manual
ADMAG TI Series
AXG###, AXG4A Magnetic Flowmeter
EtherNet/IP communication type
Read Me First
All Rights Reserved. Copyright © 2020, Yokogawa Electric Corporation.
IM 01E21A21-04EN-A
IM 01E21A21-04EN-A
1st Edition Mar. 2020 (KP)
This manual contains important information
for safe operation of this product and common
information among user's manuals on this
product. Should thoroughly read this manual prior
to other manuals before using this product.
nRegarding This User’s Manual
• This manual should be provided to the end user.
• The contents of this manual are subject to change
without prior notice.
• All rights reserved. No part of this manual may be
reproduced in any form without YOKOGAWA’s written
permission.
• YOKOGAWA makes no warranty of any kind with
regard to this manual, including, but not limited to,
implied warranty of merchantability and  tness for a
particular purpose.
• If any question arises or errors are found, or if any
information is missing from this manual, inform the
nearest YOKOGAWA sales of ce.
• The speci cations covered by this manual are limited
to those for the standard type under the speci ed
model number break-down and do not cover custom-
made products.
• Note that changes in the speci cations, construction,
or component parts of the product may not
immediately be re ected in this manual at the time of
change, provided that postponement of revisions will
not cause dif culty to the user from a functional or
performance standpoint.
• This manual is intended for the following personnel;
Engineers responsible for installation and wiring of
the product.
Personnel responsible for normal daily operation and
maintenance of the product.
• This manual is part of the product. Keep on safe
place for future reference.
NOTE
When describing the model name like AXG### in
this manual, “###”means any of the following.
For AXG###:
002, 005, 010, 015, 025, 040, 050, 080, 100, 150,
200
To ensure correct use this product, read the following
manuals. Read the following general speci cations for
its speci cation.
Enable to download the following YOKOGAWA’s web
page.
http://www.yokogawa.com/fld/
Document No. Document Title
IM 01E21A21-04EN-A
ADMAG TI Series
AXG###, AXG4A Magnetic Flowmeter
EtherNet/IP communication type
Read Me First
IM 01E22A01-01EN
ADMAG TI Series
AXG Magnetic Flowmeter
Installation Manual
IM 01E21A01-03EN-A
ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type
Installation Manual
Difference to IM 01E22A01-01EN
IM 01E22A01-02EN
ADMAG TI Series
AXG Magnetic Flowmeter
Maintenance Manual
IM 01E21A02-06EN
ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type
GS 01E22A01-01EN ADMAG TI Series
AXG Magnetic Flowmeter
GS 01E21F02-02EN-A
ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type
nPrecautions Related to the
Protection, Safety, and Alteration of
the Product
The following safety symbol marks are used in this
manual and product.
WARNING
A WARNING sign denotes a hazard. It calls attention
to procedure, practice, condition or the like, which, if
not correctly performed or adhered to, could result in
injury or death of personnel.
CAUTION
A CAUTION sign denotes a hazard. It calls attention
to procedure, practice, condition or the like, which, if
not correctly performed or adhered to, could result in
damage to or destruction of part or the entire product.
This document only applies to AXG produced at Yokogawa Corporation of America and sold to North/Central America.

2
All Rights Reserved, Copyright © 2020. Yokogawa Electric Corporation IM 01E21A21-04EN-A
IMPORTANT
An IMPORTANT sign denotes that attention is
required to avoid damage to the product or system
failure.
NOTE
A NOTE sign denotes information necessary for
essential understanding of operation and features.
The following symbols are used in the product and
the manual to indicate the accompanying safety
precautions:
Protective grounding terminal
Functional grounding terminal (This terminal should
not be used as a protective grounding terminal.)
Alternating current
Direct current
Caution
This symbol indicates that the operator must refer to
an explanation in the user’s manual in order to avoid
the risk of injury or death of personnel or damage to
the product.
• For the protection and safe use of the product and
the system in which this product is incorporated,
be sure to follow the instructions and precautions
on safety that is stated in this manual whenever
you handle the product. Take special note that if
you handle the product in a manner that violated
these instructions, the protection functionality of
the product may be damaged or impaired. In such
cases, YOKOGAWA does not guarantee the quality,
performance, function, and safety of product.
•
When installing protection and/or safety as lightning
protection devices and equipment for the product
and control system or designing or installing separate
protection and/or safety circuits for fool-proof design
and fail-safe design of the processes and lines that use
the product and the control system, the user should
implement these using additional devices and equipment.
• Should use the parts specied by YOKOGAWA when replacing.
Contact YOKOGAWA’s service ofce for fuse replacement.
• This product is not designed or manufactured to be used
in critical applications that directly affect or threaten
human lives. Such applications include nuclear power
equipment, devices using radioactivity, railway facilities,
aviation equipment, air navigation facilities, aviation
facilities, and medical equipment. If so used, it is the
user’s responsibility to include in the system additional
equipment and devices that ensure personnel safety.
• Do not modify this product.
• The product should be disposed of in accordance
with local and national legislation/regulations.
nNotesfortheIdenticationTag
An exclusive user's manual might be attached for
products whose sufx code or optional codes contain
code "Z". Read it along with their standard manual.
The Identication Tag which is attached on packing
box. Keep the Identication Tag with this document.
IdenticationTag<Sample>
F01.ai

3
All Rights Reserved, Copyright © 2020. Yokogawa Electric Corporation IM 01E21A21-04EN-A
nFor Safe Use of Product
• For the protection and safe use of the product and the
system in which this product is incorporated, be sure to
follow the instructions and precautions on safety that is
stated in this manual whenever you handle the product.
Take special note that if you handle the product in a
manner that violated these instructions, the protection
functionality of the product may be damaged or
impaired. In such cases, YOKOGAWA shall not be
liable for any indirect or consequential loss incurred by
either using or not being able to use the product.
• This product conforms to IP66/IP67 (IEC60529) and
NEMA Type 4X.
• This product is designed for indoor and outdoor use.
WARNING
• PurposeofUse
This product is the Magnetic Flowmeter for use of
measuring the liquid ow. Do not use this product
for other purposes.
• ConnecttheProtectiveGroundingTerminal
Ensure to connect the protective grounding to
prevent electric shock before turning on the power.
• DoNotImpairtheProtectiveGrounding
Never cut off the internal or external protective
grounding wire or disconnect the wiring of the
protective grounding terminal. Doing so invalidates
the protective functions of the product and poses a
potential shock hazard.
• ConnecttheFunctionalGroundingTerminal
Connect the functional grounding to stabilize the
ow rate indication.
• DoNotOperatewithDefectiveProtective
Grounding
Do not operate the product if the protective
grounding might be defective. Also, ensure to check
them before operation.
• DoNotOperateinanExplosiveandCorrosive
Atomosphere
Do not operate the product in the presence of
ammable gas, vapors, or combustible dust. Operate
the product comply to appropriate explosion-proof
certicate in the presence of ammable gas or
combustible dust. Prolonged use in a highly dense
corrosive gas (H
2
S, SO
X
, etc.) will cause a malfunction.
• DoNotRemovetheSafetyCover
The cover should be removed by YOKOGAWA’s
qualied personnel only. Opening the cover is
dangerous, because some areas inside the product
have high voltages.
• GroundtheProductbeforeMakingExternal
Connections
Connect the protective grounding before connecting
to the item under measurement or control unit.
• DamagetotheProtection
Operating the product in a manner neither
described in this manual nor the applicable manuals
listed in the front page may damage the product’s
protection.
WARNING
• Installation,Wiring,andMaintenance
• The magnetic owmeter is a heavy product. Be
careful that no damage is caused personnel
through accidentally dropping it, or by exerting
excessive force on the magnetic owmeter. When
moving the magnetic owmeter, always use a
trolley and have at least two people carry it.
• When the magnetic owmeter is processing hot
uids, the product itself may become extremely
hot. Take sufcient care not to get burnt.
• Where the uid being processed is a toxic
substance, avoid contact with the uid and avoid
inhaling any residual gas, even after the product
has been taken off the piping line for maintenance
and so forth.
• Do not apply excessive weight, for example, a
person stepping on the magnetic owmeter.
• Installation, wiring and maintenance of the
magnetic owmeter must be performed by expert
engineer or skilled personnel. No operator shall
be permitted to perform procedures relating to
installation, wiring and maintenance.
• The magnetic owmeter must be installed within
the specication conditions.
• The magnetic owmeter should be installed away
from electrical motors, transformers, and other
power sources in order to avoid interference with
measurement.
• In cases where the ambient temperature exceeds
50°C, use external heat resistant wiring with a
maximum allowable temperature of 70°C or more.
• When wiring the conduits, pass the conduit
through the cable entry, and utilize the waterproof
gland to prevent water from owing in. Install a
drain valve at the low end of the vertical pipe, and
open the valve regularly.
• When opening and closing the cover, be sure
to handle the cover carefully so that there are
no damage and foreign matter adhesion at its
threads and O-ring.
• Do not open the cover in wet weather or humid
environment. When the cover is open, stated
enclosure protection is not applicable.
• Do not connect cables outdoors in wet weather
in order to prevent condensation and to protect
the insulation, e.g. inside the terminal box of the
owmeter.
• Ensure that the power supply is off in order to
prevent electric shocks.
• When opening the terminal box, wait for more
than 20 minutes after turning off the power.
• Install an external switch or circuit breaker as a
means to turn the power off (capacitance: 15 A,
conforming to IEC60947-1 and IEC60947-3).
Locate this switch either near the product or in
other places facilitating easy operation. Afx
a "Power Off Equipment" label to this external
switch or circuit breaker.

4
All Rights Reserved, Copyright © 2020. Yokogawa Electric Corporation IM 01E21A21-04EN-A
WARNING
• Installation,Wiring,andMaintenance
• If any damages, such as cracks, breakage or
destruction on the glass of the display occurs,
stop using it and replace the cover. If it is used
with damaged glass, it may cause injury, electric
shock, malfunction, and specied protection
performance of the housing is not provided.
• Wiring work should be done adequate wire,
sleeve crimp and torque force. Use terminal with
insulating cover for the power supply wiring and
protective grounding wiring. Do not pull the wires
too much strongly in order to prevent electric
shocks caused by their damage.
• This product employs the parts which are affected
by a function damage caused by static electricity.
Thus, you should do the anti-static work using
an anti-static wrist band for it and be careful to
avoid touching each electrical parts and circuitry
directly.
• When connecting the wiring, check that the
supply voltage is within the range of the voltage
specied for this product before connecting the
power cable. In addition, check that no voltage is
applied to the power cable before connecting the
wiring.
• To prevent electric shocks, ensure the electrical
wiring cover is completely attached after the
wiring work.
• To prevent electric shocks, do not impress over
rated voltage to each input/output terminals.
• If there is any unused cable entry, use the
blanking plug to cover which comes with this
product or which is supplied by YOKOGAWA. The
blanking plug should be fastened into the unused
cable entry without any mistake. If not, stated
enclosure protection is not applicable.
Explosion protection type must be wired in
accordance with specic requirement (local legal
regulations) in order to preserve the effectiveness
of their explosion protected features.
• Maintenance of this product should be
implemented in a maintenance service shop
where the necessity tools and environment
condition are provided.
The necessity of this environmental condition
is that ambient temperature is 5 to 40°C
(the maximum relative humidity is 80 % for
temperature 5 to 31°C, and decreasing linearly to
50 % relative humidity at 40°C).
For Explosion Protection type, maintenance shall
be implemented only when there is no explosive
atmosphere present.
• All procedures relating to installation must comply
with the electrical code of the country where it is
used.
• The device can be supported as a range of
warranty only when the device is installed and
used in Control and Field network.
Operator must have the responsible for IT
security of equipment that is connected with the
device, and this device must not connect with IT
network.
In addition, parameter conguration can be
locked by hardware switch.
IMPORTANT
• Powersupply
Ensure that the source voltage matches the
voltage of the power supply before turning on the
power.
Power Supply Code 1:
• AC Type:
Rated Power Supply: 100 to 240 V AC,
50/60 Hz
• DC Type:
Rated Power Supply: 100 to 120 V DC
Power Supply Code 2:
• AC Type:
Rated Power Supply: 24 V AC, 50/60 Hz
• DC Type:
Rated Power Supply: 24 V DC
Power Consumption:
AXG4A: 13 W
nEMC
• This product conforms to the standard specications
of CIP for EtherNet/IP communication.
• Performance Specication during immunity test
Flow rate output: Output uctuation within ±5% of
default (1 m/s) span
CAUTION
This product is a Class A product in the IEC61326-1
(EMC standard). Operation of this product in a
residential area may cause radio interference, in
which case the user is required to take appropriate
measures to correct the interference.
nSafety Requirements
This product conforms to IEC safety class I (with
Protective grounding terminal), Installation Category
(Overvoltage Category) II, No Measurement Category
(“O”(Other)), Micro Pollution degree 2, Macro Pollution
degree 4, Altitude at installation Site Max. 2000 m
above sea level.
The following models are conformed to
CAN/CSA-C22.2 No.61010-1 and CAN/CSA-C22.2
No.61010-2-30.
Product Model Size
Integral
Flowmeter AXG### 2.5 to 200 mm
Remote
Sensor AXG### 2.5 to 200 mm
Remote
Transmitter AXG4A -

5
All Rights Reserved, Copyright © 2020. Yokogawa Electric Corporation IM 01E21A21-04EN-A
Subject to change without notice.
nWarrantyandDisclaimer
• Except as specied in the warranty terms,
YOKOGAWA shall not provide any warranty for the
product.
• YOKOGAWA shall not be liable for any indirect or
consequential loss incurred by either using or not
being able to use the product.
nTrademarks:
• All the brands or names of Yokogawa Electric’s
products used in this manual are either trademarks
or registered trademarks of Yokogawa Electric
Corporation.
• All other company and product names mentioned
in this manual are trade names, trademarks or
registered trademarks of their respective companies.
• In this manual, trademarks or registered trademarks
are not marked with ™ or ®.
nRevisionInformation
Title: ADMAG TI Series
AXG###, AXG4A Magnetic Flowmeter
EtherNet/IP communication
Read Me First
Manual No.: IM 01E21A21-04EN-A
Edition Date Page RevisedItem
1st Mar. 2020 –New Publication
YOKOGAWA ELECTRIC CORPORATION
Headquarters
9-32, Nakacho, 2-chome, Musashino-shi, Tokyo, 180-8750 JAPAN
Phone : [phone]
Branch Sales Offices
Osaka, Nagoya, Kurashiki, Hiroshima, Fukuoka, Kitakyusyu
YOKOGAWA
CORPORATION OF AMERICA
Head Office
12530 West Airport Blvd, Sugar Land, Texas 77478, USA
Phone : [phone] Fax : [phone]
Georgia Office
2 Dart Road, Newnan, Georgia 30265, USA
Phone : [phone] Fax : [phone]