ADS-tec OPC8017 User manual

Updated 2019-07-17
Instruction manual
Industrial PCs
OPC8017 OPC8024 /
OPD8017 OPD8024
Version 2.1
Translation of the original
instruction manual

OPC8017 OPC8024 / OPD8017 OPD8024 2
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
Read these instructions carefully before using and store for future reference.
These instructions contain important information about the product, in particular about its
intended use, safety, installation, utilisation, maintenance and disposal.
Hand over the instructions to the user following installation of the product, and pass the
manual on to the new user if the product is resold.
These instructions can be downloaded from: www.ads-tec.de in the download area.
Publisher
ads-tec Industrial IT GmbH
Heinrich-Hertz-Straße 1
72622 Nürtingen
Phone: [phone]
Internet: www.ads-tec.de
E-mail: [e-mail]

OPC8017 OPC8024 / OPD8017 OPD8024 3
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
Table of Contents
1Device description...........................................................................................................6
2General information ........................................................................................................8
2.1 Information about documentation 8
2.1.1 General remark 8
2.1.2 Limitation of liability 8
2.1.3Manufacturer and contact details 9
2.1.4 Relevant device documentation 9
2.1.5 Symbols 9
2.1.6 Data, figures and modifications 10
2.1.7 Trademarks 10
2.1.8 Copyright 10
2.1.9 Standards 10
2.2 Explanation of safety instructions 11
2.2.1 Structure of safety instructions 11
2.2.2 Explanation of signal words 12
2.3 Safety instructions 13
2.3.1 Basic safety instructions 13
2.3.2 Environmental conditions 14
2.3.3 Intended use 15
2.3.4 Improper use 15
2.3.5 Damage due to improper use 15
2.3.6 Warranty / repairs 16
2.3.7 Treatment and disposal of lithium batteries 16
2.3.8 Electrostatically sensitive components 17
3Scope of delivery...........................................................................................................18
3.1 Optional scope of delivery 19
4Installation .....................................................................................................................20
4.1 Preparing installation location 22
4.2 Installing device 23

OPC8017 OPC8024 / OPD8017 OPD8024 4
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
5Interfaces .......................................................................................................................26
5.1 Interfaces of OPC8017/OPC8024 27
5.2 Interfaces of OPD8017/OPD8024 30
5.2.1 Maximum cable lengths 31
5.3 Functional earthing 32
5.3.1 General informations regarding functional earthing 32
5.3.2 Functional earthing OPC 32
5.3.3Functional earthing OPD without HDBaseTTM Extender Kit 33
5.3.4 Functional earthing OPD with HDBaseTTM Extender Kit 33
6HDBaseT™ Extender Kit ...............................................................................................34
6.1 Installation of receiver module 34
6.2 Interfaces of receiver module 35
6.3 Cabling 36
6.4 Interfaces of transmitter module 36
6.5 Status indicators 38
6.5.1 Status indicators on transmitter module 38
6.5.2 Status indicators on receiver module 39
7Commissioning .............................................................................................................40
8Operation .......................................................................................................................42
8.1 Switching on and off 42
8.2 Multifunction touch-screen 42
8.3 Component replacement 43
8.3.1 Replacing BIOS battery (OPC8017/OPC8024) 43
8.3.2 Replacing mass storage device 45
8.3.3 Replacement parts list 47
9Maintenance, cleaning and disposal............................................................................48
9.1 Maintenance 48
9.2 Cleaning 48
9.3 Disposal 49

OPC8017 OPC8024 / OPD8017 OPD8024 5
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
10 Nomenclature of ADS-TEC products and accessories............................................... 50
10.1 Main articles 50
10.2 Accessory articles 51
10.2.1 Display and USB transmission 51
10.2.2 Support arm adapter 52
10.2.3 Product kits 52
11 Technical data ...............................................................................................................53
11.1 Technical data – OPD/OPC8000 series 53
11.1.1 Data sheet 53
11.1.2 External device dimensions OPC8017 54
11.1.3 External device dimensions OPC8024 55
11.1.4 External device dimensions OPD8017 56
11.1.5 External device dimensions OPD8024 57
11.2 HDBaseT™ Extender Kit technical data 58
11.2.1 Data sheet 58
11.2.2 External device dimensions – HDBaseT™ Extender Kit transmitter 59
11.2.3 External device dimensions – HDBaseT™ Extender Kit receiver 60
12 List of figures.................................................................................................................61
13 Service & support..........................................................................................................62
13.1 ADS-TEC support 62

OPC8017 OPC8024 / OPD8017 OPD8024 6
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
1 Device description
OPC8017/OPC8024 (Operating Panel Computer) and OPD8017/OPD8024 (Operating Panel Display)
are designed for the control and visualisation of production processes in the pharmaceutical, foodstuff,
beverage and chemical industry. In the case of the OPC, the processing unit is integrated in the
housing, making an external PC unnecessary for control. The OPD is a display which can be
controlled by an external computer, e.g. from the existing industrial computer environment. Cables can
be used for distances of up to 15 m between the computer and OPD. The optional extender kit has
been developed to bridge greater distances of up to 100 m. Both the computer and the display option
are available in the 17 and 24 inch format.
Figure 1: Use of OPC / OPD

OPC8017 OPC8024 / OPD8017 OPD8024 7
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
The devices have been specially developed to fulfil strict hygiene requirements. This is achieved by
the stainless steel housing of the device being completely closed at the front, having rounded edges
and no external screws. This allows the device to be cleaned simply and effectively. The device has
no fan, which means that the primary source of contamination is not present. Due to its robust,
compact design, the device can also be operated under demanding environmental conditions.
Thanks to the very latest multi-touch technology, the display can be operated conveniently by tapping
and also by means of swiping and dragging movements. Operation with gloves is also possible.
The devices are designed to be installed in a switch board or cabinet door. All of the necessary cables
are routed on the rear side so that there are no exposed cables at the front.
Figure 2: Touch surface

OPC8017 OPC8024 / OPD8017 OPD8024 8
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2 General information
2.1 Information about documentation
2.1.1 General remark
This instruction manual is intended to ensure safe and efficient handling and operation of IT
Infrastructure products.
The instruction manuals must be read carefully by personnel before commencing any type of work.
All of the safety instructions and handling instructions given in the manual must be obeyed in order to
ensure that work is carried out safely.
Operation of the system is subject to the laws and regulations which are applicable in the respective
country at national, federal, European and international level.
The generally accepted rules of technology, usually in the form of standards, directives, regulations,
conditions and technical rules specified by national and federal organisations as well as trade
associations and committees for the field of specialisation concerned, shall apply.
Figures used in this instruction manual are provided for basic understanding and may differ from the
actual design.
The operator/operating company is independently responsible for compliance with and observance of
any subsequently introduced technical innovations or new legal requirements, as well as for all usual
obligations of the operator/operating company.
The original version of this instruction manual was written in German. All non-German versions of this
instruction manual are translations of the German instruction manual.
2.1.2 Limitation of liability
ads-tec GmbH shall not be liable for personal injury, property damage or damage caused to the device
as well as consequential damage that is/was the result of non-compliance with this instruction manual,
improper use of the device, repairs and other actions on the device by unqualified electricians and
electricians not certified by ADS-TEC, or that is/was the result of using unapproved replacement parts.
Failure to observe the maintenance intervals shall also result in exclusion from liability. Furthermore, it
is strictly forbidden to make any unauthorised alterations or technical modifications to the device.

OPC8017 OPC8024 / OPD8017 OPD8024 9
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2.1.3 Manufacturer and contact details
The manufacturer of the product is ads-tec GmbH. The company is referred to in the following as
ADS-TEC.
ads-tec GmbH
Heinrich-Hertz-Str.1
72622 Nürtingen
Germany
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.ads-tec.de
2.1.4 Relevant device documentation
The following documents are decisive to device setup and operation:
Instruction manual:
Contains information for installation, commissioning and operation of the device along with technical
data of the device hardware.
Website
You can download the instruction manual as well as drivers, software, user manuals, leaflets and
flyers from the Download area of our website www.ads-tec.de.
2.1.5 Symbols
Symbol Meaning
Designation of batteries. Batteries may not be disposed of with household waste, but must
rather be disposed of separately. Used batteries must be returned to the point of sale or a
disposal system
Labelling of electrical and electronic devices. Electrical and electronic devices must not be
disposed of with household waste, but must rather be taken to a collection point for waste
electrical equipment. Such a collection point is generally operated by public waste
management authorities, i.e., by municipalities.
Symbol for the functional earth connection

OPC8017 OPC8024 / OPD8017 OPD8024 10
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2.1.6 Data, figures and modifications
All data, text and figures were prepared to the best of our knowledge. They do not represent any
assurance for the properties themselves. Despite taking utmost care, no liability can be assumed for
accuracy, completeness and actuality of the information. Subject to changes.
2.1.7 Trademarks
It is noted that any software and/or hardware trademarks and any company brand names mentioned
in this documentation are all subject to the general trademark protection rights.
StoraXe® and Big-LinX® are registered trademarks of ADS-TEC.
All other used third-party trademarks are hereby acknowledged.
In the case of trademark infringement, ADS-TEC reserves the right to exercise all rights.
2.1.8 Copyright
This instruction manual is protected by copyright. For the authorised user, simple usage rights are
granted within the scope of the intent of the contract. Any modified use or exploitation of the provided
content, particularly duplication, modification or publishing in whatever form is permitted only with the
prior consent of ADS-TEC.
In the case of copyright infringement, ADS-TEC reserves the right to exercise all rights.
2.1.9 Standards
The manufacturer hereby declares that the product described in this instruction manual complies with
all relevant stipulations of the following European directives:
•2011/65/EU, RoHs Directive
•2014/30/EU, EMC Directive
•2014/53/EU, RED Directive
•2014/35/EU, Low Voltage Directive
The product is a class B device.
Note: For full compliance with the EMC legislation, all components and cables used for device
connection must also be compliant with these requirements. It is therefore necessary to employ BUS
and LAN cables with shielded connectors and these must be installed as per the instructions
contained in the instruction manual.

OPC8017 OPC8024 / OPD8017 OPD8024 11
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
A corresponding EU conformity declaration is available for competent authorities at the manufacturer
and can be viewed upon request.
The EU conformity declaration can be requested on our website www.ads-tec.de and downloaded in
the Download area.
The product also complies with the following UL standards:
oUL 61010-1 Programmable Controllers
oUL 61010-2-201 UL file number E343358
oCAN/CSA-C22.2 No. 61010-1
oCAN/CSA-C22.2 No. 61010-2-201
2.2 Explanation of safety instructions
2.2.1 Structure of safety instructions
The signal word classifies the hazard.
Reference to the type/consequences and source of the hazard is made underneath the signal word.
Information on how to avoid the hazard is indicated by an arrow ().
DANGER
Type and source of the hazard!
Possible consequences if the hazard is disregarded
Measures for avoiding the hazard

OPC8017 OPC8024 / OPD8017 OPD8024 12
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2.2.2 Explanation of signal words
DANGER
Indicates an imminent danger. If not avoided, death or severe injury will
result.
WARNING
Indicates a possible danger. If not avoided, death or severe injury could
result.
CAUTION
Indicates a possible danger. If not avoided, light or minor injuries could
result.
ATTENTION
Indicates a possibly damaging situation. If not avoided, the system or something in its
surroundings could be damaged.
Recommendation for use:
Indicates terms and/or conditions that strictly need to be observed to ensure
optimised and/or zero-defect operation. Tips and suggestions for the efficient use
of the device and software optimisation are also provided.

OPC8017 OPC8024 / OPD8017 OPD8024 13
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2.3 Safety instructions
2.3.1 Basic safety instructions
•All users must read this manual and have access to it at all times.
•The safety notices and the manual itself must be observed by all persons who work with this
device.
•The manual contains the most important instructions on how to use this device in a safe way.
•Intervention by the user is required only for performing the actions described in this document.
Should any further modifications be required, it is necessary to consult either with the
manufacturer directly or with service personnel authorised by the manufacturer.
•The device must be de-energised during work. Appropriate measures must be taken to
prevent electrostatic discharges on components.
•If the device is opened up by an unauthorised person, the user may be subject to hazards and
the warranty is invalidated.
•Installation, commissioning and operation may only be performed by qualified and trained
personnel.
•At the installation site the valid guidelines and regulations for accident prevention must be
observed.
•Appropriate storage, proper transport, installation and commissioning, as well as careful
operation are prerequisites for ensuring safe and proper operation of the device.
•The device can be cleaned using cleaning agents specified in the chapter 9.2.

OPC8017 OPC8024 / OPD8017 OPD8024 14
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
2.3.2 Environmental conditions
The device can be put into operation and used under the following environmental conditions. Failure to
observe any one of these conditions will invalidate the warranty of the device. ADS-TEC cannot be
held liable for any damages arising from improper use and handling.
Use of the device is only permitted
- in enclosed buildings
- in non-explosive atmospheres
- at altitudes below 3000 m
- in environments with maximum contamination grade 2 (IEC/EN 61131-2)
ATTENTION
Damage caused by condensation!
If the temperature of the device is different to that of the room in which it is located, condensation
can form.
ATTENTION
Damage caused by heat!
If the device is exposed to sunlight or any other light or heat source, it can overheat and suffer
damage.
ATTENTION
Damage caused by heat!
If the device is installed in a panel, casing or similar, heat accumulation can occur.
Make sure that heat can be dissipated from the device!

OPC8017 OPC8024 / OPD8017 OPD8024 15
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
The device can be operated under the environmental conditions (temperature, humidity, vibration and
shock) which are specified in the data sheet in chapter 10. Failure to observe any one of these
conditions will invalidate the warranty of the device. ADS-TEC cannot be held liable for any damages
arising from improper use and handling.
The climatic conditions were tested according to:
IEC/EN 60068-2-1
IEC/EN 60068-2-2
IEC/EN 60068-2-14
Protection class: IP65 according to DIN EN 60529
2.3.3 Intended use
The control system is designed for use in the pharmaceutical, food, beverage and chemical industries.
It was specially developed for the hygiene sector. The device is used for the visualisation and control
of a wide range of processes on systems and machines in various application environments.
The device is only to be assembled, installed and operated within the permissible specifications. Use
in non-specified environments is prohibited.
2.3.4 Improper use
Operation other than or beyond that described for the device shall be deemed improper use.
The device is not allowed to be used to control vehicles or for applications for which further approvals
beyond the manufacturer's declaration are necessary, e.g. applications with explosion hazard, medical
technology and shipping industry.
The device must not be put into operation in the case of transport damage or nonconformity with the
specifications and, if necessary, must be taken out of operation in the case of changing conditions.
In the case of improper use, ADS-TEC shall not accept responsibility or liability for injury or damage
that is directly or indirectly attributable to the handling of the device.
2.3.5 Damage due to improper use
ATTENTION
Risk of mechanical damage!
The device can be damaged as a result of unauthorised mechanical modifications.
Make sure that the device is not drilled, chiselled or perforated and its exterior shape and design
is not modified in any way!

OPC8017 OPC8024 / OPD8017 OPD8024 16
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
Should the control system have evident signs of damages caused, e.g., by transport, nonconformity
with the specifications, improper operation and storage conditions or due to improper use or handling,
the device must be shut down immediately. Ensure that it is secured against being started up
accidentally.
2.3.6 Warranty / repairs
During the device warranty period, any repairs must only be performed by the manufacturer or by
service personnel that has been authorised by the manufacturer.
2.3.7 Treatment and disposal of lithium batteries
WARNING
Hazard due to explosion
Danger of explosion if using incorrect battery types.
Use the battery type recommended by the manufacturer!
ATTENTION
Hazard due to thermal loads
The more the battery is exposed to higher temperatures, the faster it ages.
Operate the device within its specifications!
ATTENTION
Damage to the battery
Incorrect handling of the battery can cause it to be damaged or destroyed
Lithium batteries should not be exposed to fire, soldered, recharged, opened, short-circuited,
reversed or heated above 100 °C and they should be disposed of properly as well as
protected against sunlight, moisture and condensation!

OPC8017 OPC8024 / OPD8017 OPD8024 17
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
This device contains a lithium battery for supplying the system clock with power as long as the supply
voltage is not connected. The battery has a life cycle of 3-5 years depending on which load is applied.
The battery type to be used is:
Lithium battery CR2032 230 mAh
ADS-TEC part number: DZ-SONS-04075-1
The used lithium battery should be disposed of in accordance with local legal regulations.
2.3.8 Electrostatically sensitive components
Recommendation for use:
Always adhere to the safety measures applicable when handling components at
risk of being damaged by electrostatic discharges.
The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply
ATTENTION
Damage due to electrostatically sensitive components
Damage to the device can be caused by electrostatically sensitive components.
All installation and service work performed on the device must be performed only under safe,
secure and de-energised conditions!

OPC8017 OPC8024 / OPD8017 OPD8024 18
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
3 Scope of delivery
Please check that all of the following components are contained in the packaging:
OPC8017
Device DVG-OPC8017
4-pin plug (power supply) DZ-SONS-01222-1/*
18 x clamping block M4 DZ-MECH-31024-0
18 x threaded pin M4x30 DZ-MECH33695-0/A
OPC8024
Device DVG-OPC8017
4-pin plug (power supply) DZ-SONS-01222-1/*
26 x clamping block M4 DZ-MECH-31024-0
26 x threaded pin M4x30 DZ-MECH33695-0/A
OPD8017
Device DVG-OPD8017
3-pin plug (power supply) DZ-SONS-00994-2
18 x clamping block M4 DZ-MECH-31024-0
18 x threaded pin M4x30 DZ-MECH33695-0/A
ATTENTION
Damage to components containing soft parts!
If the soft material is subjected to a concentrated load, e.g., by placing it on a grating, irreversible
impressions will form after some time.
Make sure that a suitable surface is provided when setting down the device on its display side!

OPC8017 OPC8024 / OPD8017 OPD8024 19
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
OPD8024
Device DVG-OPD8024
3-pin plug (power supply) DZ-SONS-00994-2
26 x clamping block M4 DZ-MECH-31024-0
26 x threaded pin M4x30 DZ-MECH33695-0/A
3.1 Optional scope of delivery
Operating system (only for OPC8017 and OPC8024)
HDBaseT™ Extender Kit (only for OPC8017 and OPC8024)
Transmitter module
DV-MMDEXT-TX
Receiver module
DV-MMDEXT-RX
USB cable
DZ-SONS-05647-0/*
HDMI cable
DZ-SONS-05646-0/*
Cable for power supply
DZ-SONS-09796-0/*

OPC8017 OPC8024 / OPD8017 OPD8024 20
© ads-tec Industrial IT GmbH • Heinrich-Hertz-Str. 1 • 72622 Nürtingen • Germany
4 Installation
ATTENTION
Damage caused by heat!
If the device is installed in a panel, casing or similar, heat accumulation can occur.
Make sure that heat can be dissipated from the device.
ATTENTION
Damage caused by heat!
If the device is exposed to sunlight or any other light or heat source, it can overheat and suffer
damage.
Do not expose the device to direct radiation by sunlight or any other light or heat source.
ATTENTION
Damage to the electronics!
If a device with data drive is not installed vertically, the electronics may suffer damage.
Install devices with data drive vertically only. Deviations must be arranged with ADS-TEC.
ATTENTION
Mechanical damage!
If the device is not mounted correctly, IP65 protection will not be provided.
Tighten the screws to a torque of 0.5 Nm.