ADTRAN MX2820 User manual

jobAid
1
DESCRIPTION
The MX2820 M13 MUX is a plug-in unit for
the MX2820 chassis that provides an M13
multiplexer function to the MX2820 system.
Two MX2820 M13 MUX modules are used
together to provide a redundant M13 multi-
plexer circuit. The MX2820 M13 MUX:
•Provides 1-to-1 redundancy
•Meets the requirements for NEBS Level 3.
SAFETY AND REGULATORY
COMPLIANCE
RefertotheSafetyandRegulatory
ComplianceNoticeforthisproduct(P/N
61186002F1‐17)fordetailedsafetyand
regulatoryinformation.
Consultez l'avis sur la sécurité et la
conformité à la réglementation pour ce
produit (61186002F1‐17) pour obtenir des
renseignements détaillés sur la sécurité et la
réglementation.
Ausführliche Sicherheits- und regula-
torische Informationen sind in der Konformitätserklärung zur
Sicherheit und Einhaltung von Normen zu diesem Produkt
(61186002F1‐17) aufgeführt.
INSTALLATION
After unpacking the unit, inspect it for damage. If damage is found,
file a claim with the carrier and then contact ADTRAN Customer
Service. Refer to the warranty statement on this Job Aid.
This module occupies a MUX slot in the MX2820 chassis. To install
the M13 MUX in the chassis, perform the following steps:
1. Pull the ejector tab into the down position and gently but firmly
push the MUX into the selected MUX slot. Simultaneous thumb
pressure at the top and at the bottom of the MUX ensures a
good seat of the MUX into the backplane connector.
2. Push the ejector tab up and closed against the front panel.
Upon installation, the MUX begins a self-test. This is followed with
the LEDs reflecting the true state of the hardware.
OPERATIONAL SPECIFICATIONS
•Operates from A or B input voltage power feeds.
o–48 VDC Systems: –42 VDC to –56 VDC
o–24 VDC Systems: –22 VDC to –27 VDC
o+24 VDC Systems: +22 VDC to +27 VDC
•Operates over extended temperature range of –40ºC to +50ºC
(without fans) or –40ºC to +65ºC (with fans)
•Storage –40ºC to +85ºC (Relative humidity to 95 percent,
noncondensing)
1186002
M13 MUX
ALM
ACT
TEST
STAT
TEST
STAT DS1
DS3
MX2820
M13 MUX
LED STATUS FOR ACTIVE MUX
LED STATUS FOR STANDBY MUX
Label Status Description
ACT z
z/z
z
z/z
z
2
Green
Green/Yellow
(Alternating)
Yellow
Yellow/Red
(Alternating)
Red
Red (Flashing)
Normal (All OK)
Normal and console open
Software update in progress
Self-test failed and console open
Self-test failed
Module has failed
ALM z
z
4
Green
Red
Red (Flashing)
No critical, major, or minor alarms
Major or minor alarm in progress
Critical alarm in progress
DS3 STAT z
z/z
z
2
2
Green
Green/Red
(Alternating)
Red
Red (Flashing)
Red (Flashing
once per event)
Normal (DS3 OK)
DS3 XCV threshold exceeded
AIS, OOF, RAI, Idle alarms
DS3 LOS or DS3 Failure (critical)
Single/Burst DS3 code violations
DS3 TEST {
z
2
Off
Yellow
Yellow (Flashing)
No DS3 tests in progress
In test (locally originated)
In test (remotely originated)
DS1 STAT {
z
z/z
z
4
2
Off
Green
Green/Red
(Alternating)
Red
Red (Flashing)
Red (Flashing
once per event)
All DS1s are disabled
Enabled DS1s normal (All OK)
DS1 XCV threshold exceeded
Non-critical DS1 alarm (CAIS,
LAIS)
LOS on an enabled line (critical
DS1 alarm; non-critical system
alarm)
Single/Burst RX DS1 code viola-
tion
DS1 TEST {
z
2
Off
Yellow
Yellow (Flashing)
No DS1 tests in progress
In test (locally originated)
In test (remotely originated)
Label Status Description
ACT 2
z
z
Green (Flashing)
Yellow
Red
Normal (All OK)
Software update in progress
Failure
ALM {Off Permanent state during standby
DS3 STAT {
2
Off
Red (Flashing)
Normal (DS3 OK)
In test (remotely originated)
DS3 TEST {Off Permanent state during standby
DS1 STAT {
2
Off
Red (Flashing)
Normal (DS1s OK)
DS1 Failure
DS1 TEST {Off Permanent state during standby
CLEI: M3C3RG0A_ _
Product P/N: 1186002F1
Issue Date: November 2011
Document P/N: 61186002F1-22A

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
©2011 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61186002F1-22A*
PROVISIONING
All provisioning of the MX2820 M13 MUX is handled through the SCU. The menu tree below provides the options and default settings for
the MX2820 M13 MUX.
1. Configuration 3. Status 4. Test 5. Performance Monitoring
4. Protection
Note: An asterisk (*) indicates default setting
5. Save Provisioning
1. 0-133 ft*
T1:
E1:
3. 266-399 ft 2. 133-266 ft 5. 533-655 ft 1. 0-6dB Loss 4. 399-533 ft 1. 2 seconds*
29. Set Multiple 30. Auto Enable Delay
3. 2 hours 2. 1 hour 5. 1 day 4. 12 hours 6. 2 days 7. 7 days
1. Disabled 3. 5 Minutes* 2. 1 Minute 5. 15 Minutes 4. 10 Minutes 6. 30 Minutes 7. 45 Minutes 8. 60 Minutes
1. Near End Daily 3. Far End Daily 2. Near End Quarter Hourly 5. Near End Daily Thresholds 4. Far End Quarter Hourly 6. Near End Quarter Hourly Thresholds 7. Near End Daily Thresholds 8. Near End Quarter Hourly Thresholds 9. Clear DS3 Statistics
1. Data Mode* 3. Digital Loopback 2. Line Loopback 5. Remote ALL T1/E1 4. Remote Loopback 1. QRSS* 3. ALL ZEROES 2. ALL ONES 5. 1 in 8 (1:7) 4. 2 in 8 (2:6) 6. 2 ^15-1 INV 1. Data Mode* 2. Network Loopback 1. Data Mode*
T1:
3. Analog Network 2. Tributary 5. CODEC Line/Net 4. Digital Line/Net 6. Remote Loopback 7. LS CSU Loopback 8. LS CSU LB w/BERT 9. LS NIU Loopback 10. LS NIU LB w/BERT 11. LS Line BERT 1. Data Mode*
E1:
T1/E1 Loopbacks (T1/E1 #1-28)
29. DS3 Loopbacks
3. Analog Network 2. Tributary 5. CODEC Line/Net 4. Digital Line/Net 6. Remote Loopback 7. LS Line BERT
CLEI Code Serial Number Part Number Code Checksum Code Version Boot Version Boot Checksum Self Test
1. Disabled*
3. 1E-4 2. 1E-3 5. 1E-6 4. 1E-5
1. Disabled* 3. 1E-4 2. 1E-3 5. 1E-6 4. 1E-5
1. Near End Daily 3. Near End Daily Thresholds 2. Near End Quarter Hourly 4. Near End Quarter Hourly Thresholds 5. Clear T1/E1 Statistics
1. Disabled 3. FEAC 2. FEAC/C-BIT* 4. C-BIT
1. DS3 Framing 3. DS3 Remote Loopbacks 2. DS3 Timing 8-14. DS2 Mode (DS2 #1-7) 4. DS3 XCV Threshold
1. T1/E1 State 3. T1/E1 Line Length 2. T1/E1 Line Coding 5. T1/E1 Circuit Protection 4. T1/E1 Loopback Detection 6. T1/E1 Line Identification 7. T1/E1 XCV Threshold
(T1/E1 #1-28)
(T1/E1 #1-28) (T1/E1 #1-28) (T1/E1 #1-28)
(T1/E1 #1-28)
7. Card Reset 1. Network Interface 2. T1/E1 Interfaces 3. Service States 6. Restore Factory Defaults 8. Auto Save 9 . Loopback Timeout 10 . Card Pair ID
1. AMI
2. B8ZS/HBD3* 1. Disabled 2. Enabled 3. Auto Enable*
T1/E1 #1-28 29. DS3 30. Set Multiple
1. Card nA 2. Card nB 3. Facility Service States
2. Enabled* 1. Disabled
30. Protection Threshold (1-28): 1*
2. Enabled* 1. Disabled
1. Disabled* 2. CSU (T1 Only) 3. NIU (T1 Only)
1. Perform Manual Switch 2. Minimum Switching Period (sec.) (10*) 3. Maximum Switch Threshold (3*)
1. DS3 Statistics 2. T1/E1 Statistics 3. Clear ALL Statistics
1. M12 (4xT1)* 2. G.747 (3xE1) 1. C-BIT 2. M13* 1. IS* 2. OOS 1. Loop 2. Local*
30-36. DS2 #1-7 Loopbacks 37. Reset ALL Tests 38. Pattern
15. DS3 Equipment Identification
(T1/E1 #1-28)
12. HS CSU Loopback
13. HS CSU LB w/BERT
14. HS NIU Loopback 15. HS NIU LB w/BERT 16. HS Line BERT
6. IP Forwarding Protocol 7. IP Forwarding MTU
1. ADTRAN* 2. PPP 1. 260 (PREFERRED)*
4. Clear Number of Switches
8. HS Line BERT
2. 1500
29. Set Multiple (T1/E1 #1-28)
2. Provisioning
Main Menu
5. DS3 TX Level 1. Normal*
2. Low