ADTRAN D4 FT1 DP User manual

The ADTRAN FT1 DP occupies one physical channel unit of an AT&T
Network System (WECO™) D4. The ADTRAN FT1 DP works with the ADTRAN
Fractional T1 Network Interface Device (FNID). Together the units support
two-way fractional T1 transport at rates of 128, 256, 384, 512, 640, and 768
kbps over an existing CSA loop plant, without loop conditioning or service
degradation. The technology used in the FT1 DP is High-bit-rate Digital
Subscriber Line (HDSL). The HDSL transport complies with the specifica-
tions contained in Bellcore TA-NWT-0001210, FA-NWT-0001211, and ANSI
T1E1 HDSL Technical Report - TR28.
The FT1 DP can span power the (FNID). In addition, the FT1 DP is capable
of span powering a Fractional T1 repeater which can be used to double the
deployment range of a circuit. The FT1 DP maintains all provisioning
options of the FT1 circuit. These options are set either manually (through
DIP switches) or through a craft access RS-232 interface (DB-9). The FT1 DP
also provides extensive Operation, Administration, Maintenance, and
Provisioning (OAM&P) information through faceplate features or the ter-
minal interface.
HDSL local loop operation is independent of the channel bank chosen
to deploy the FT1 DP units. The FT1 DP is the master in the master/slave
relationship with the FNID. The FT1 DP provides span powering to the
FNID, if required by the application. Additionally, the FT1 DP provisions
and maintains the FT1 circuit. Provisionable options may be selected
through manual switch selections and through a controlling terminal
interface. Once selected, these options can be changed by either of these
two methods; the FT1 DP remembers the last change implemented.
PRODUCT FEATURES
■Repeaterless FT1 over Carrier
Service Area (CSA) loops
■FT1 service rates of 128 to
768 kbps in increments of
128 kbps
■2B1Q modulation
■Front panel LEDs to indicate
system status
■Manual DIP switches at FT1 DP
as well as remote provisioning
■Local or remote performance
monitoring capability
■Loopbacks with DDS latching
loopback codes
■Operation over extended
temperature ranges (standard
–40° to +70°C)
■Supports operation of Fractional
T1 Repeater
■Standard 10 year warranty
D4 FT1 DP
FRACTIONAL T1 DATAPORT
FOR AT&T D4 CHANNEL BANK

Product Specifications
PROVISIONABLE OPTIONS
■Channel Selection (alternate or
contiguous)
■Line Coding
■Framing
■Latching Loopback
■DS1 Equalization
■Loopback Timeout
■Loopback “keep alive” setting
■SNR Thresholds
■Attenuation Thresholds
■Error Threshold
■Idle Code Detection
■SLC-96 Mode of Operation
■A/B Bit Signalling
FACEPLATE FEATURES
■ LEDs:
— Power Indication for HTU-C supply
— Loop Synchronization and Signal Quality
— Attenuation
— Local and/or Remote Alarm Indication
— Loopback Indication
— Sealing Current (with or without Span
Powering) on Local Loop
— Self Test
■ Jacks:
— DS0 Break Out Jack
— RS-232 Interface (DB-9)
■ Rotary Dial: Used to select data rate
Ordering Information
EQUIPMENT PART #
D4 FT1 DP.............................................1242040L1
Specifications subject to change without notice.
CORPORATE OFFICE
901 Explorer Boulevard
Huntsville, AL 35806
800 9ADTRAN
Local: 256 963-8000
Fax: [phone]
Fax Back: 256 963-8200
http://www.adtran.com
email: [email protected]
TELCO TECHNICAL
SUPPORT
800 726-8663
REGIONAL OFFICES
Irvine, CA
800 788-5408
Denver, CO
800 471-8651
Atlanta, GA
800 332-6945
Kansas City, KS
800 471-8649
Philadelphia, PA
800 471-8656
Dallas, TX
800 471-8648
Canada
800 232-6811
ADTRAN is an ISO 9001
registered company.
Printed in U.S.A. on recycled paper
61242.040L1-8C May 1998
©ADTRAN, Inc. 1998