ADTRAN TSU LT User manual

TSU LT P/N 1202060L2/1202060L4
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide, 61202060L4-13A, May 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
NETWORK CONNECTION PINOUT
Pin Name Description
1 R1 RXDATA Receive data from the Network - Ring
2 T1 RXDATA Receive data from the Network - Tip
3, 6, 7, 8 UNUSED n/a
4 R TXDATA Transmit data towards the Network - Ring
5 T TXDATA Transmit data towards the Network - Tip
INSTALLATION INFORMATION
• An eight-position modular jack (labeled NETWORK) is provided to
connect to the network T1 circuit. The pinout is provided on this Quick
Start Guide. See Chapter 2, Installation, of the TSU LT User Manual for
more information.
• The rear panel contains a single V.35 (V.11 for P/N 1202060L4)
interface for connecting to DTE equipment. The pinouts for these
interfaces are provided on this Quick Start Guide.
• When shipped from the factory, the TSU LT is uninitialized and set to
factory default conditions. At the first application of power, the unit will
automatically execute self-tests followed by an initialization sequence.
• The TSU LT can be configured and controlled using the local front panel
of the unit, by a direct or remote serial connection via the control port, or
by ADTRAN’s PC-based management software package,
T-WATCH PRO. A limited menu tree is provided on the back of this
sheet. For more detailed menu information, refer to the TSU LT User
Manual.
• Additional information can be found on the product CD which contains
the TSU LT User Manual, FAQs, Data Sheets, Applications, and White
Papers.
REAR PANEL DESCRIPTIONS
Network Connector Connection to T1 circuit
Test Interface
(P/N 1202060L2 only)
Bantam jacks provided for monitoring
and testing of a T1 circuit
Control Chain-In/Chain-Out Connection to a VT100 terminal
V.35 Connector (P/N 1202060L2)
V.11 Connector (P/N 1202060L4)
High-speed DTE interface
Power Switch Turns power to the TSU on or off
220 VAC Connection Power cord connection for a reliably
grounded 220 VAC, 60 Hz power source

TSU LT P/N 1202060L2/1202060L4
Quick Start Guide, 61202060L4-13A, May 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
MENU TREE - OVERVIEW
1) NI PERF RPRTS
1) STATUS 2) CURR ERR/ALM
3) ERR/ALM HIST
1) NETWORK (NI)
2) CONFIG 2) UNIT
MAIN MENU 3) PORT
1) TIME/DATE
2) SOFTWARE REV
3) UTIL 3) REINIT UNIT
4) ADDRESS
5) SET PASSCODE
6) FACT RESTORE
1) NETWORK TESTS
4) TEST 2) RUN SELF–TEST
3) PORT TESTS
V.35 CONNECTOR PINOUT
Pin CCITT Description
A 101 Protective ground (PG)
B 102 Signal ground (SG)
C 105 Request to send (RTS) from DTE
D 106 Clear to send (CTS) to DTE
E 107 Data set ready (DSR) to DTE
F 109 Received line signal detector (DCD)
to DTE
H — Data terminal ready (DTR) from
DTE
J — Ring indicator (RI)
L — Local loopback (LL)
N — Remote loopback (RL)
R 104 Received data (RD-A) to DTE
T 104 Received data (RD-B) to DTE
V 115 RX clock (RC-A) to DTE
X 115 RX clock (RC-B) to DTE
P 103 Transmitted data (TD-A) from DTE
S 103 Transmitted data (TD-B) from DTE
Y 114 TX clock (TC-A)
AA 114 TX clock (TC-B)
U 113 External TX clock (ETC-A) from
DTE
W 113 External TX clock (ETC-B) from
DTE
NN&K — Test mode (TM) to DTE
V.11 CONNECTOR PINOUT
Pin A Pin B Description
1
2*
Shield
(SI) Signalling Rate Indicator
4
5
22
23
(SD) Send Data
(ST) Send Timing
6
7
24
25
(RD) Receive Data
(RS) Request to Send
8
9
26
27
(RT) Receive Timing
(CS) Clear to Send
10
11 29
(LL) Local loopback
(DM) Data Mode
12* 30* (TR) Terminal Ready
13 31 (RR) Receiver Ready
14
15*
(RL) Remote Loopback
(IC) Incoming Call
16*
17 35
(SR) Signaling Rate Selector
(TT) Terminal Timing
18
19
(TM) Test Mode
(SG) Signal Ground
20*
28*
(RC) Receive Common
(IS) Terminal in Service
32*
33*
(SS) Select Standby
(SQ) Signal Quality
34*
36*
37*
(NS) New Signal
(SB) Standby Indicator
(SC) Send Common
Note: Pins 3 and 21 are undefined.
* Indicates pins not being used
Compliance
Double pole/neutral fusing.
The socket-outlet shall be
installed near the equipment
and shall be easily accessible.