Advance acoustic PACEMAKER 17/20 User manual

1HIENNAiIONALHEA00UIRIER3, Phma^MN E5H74108
EUPOPE, GUnuisinl, Pontwiu q M(6(3lampqan CF7 L1Z W^Im, UnMeO K^qdan
CANA OA, t E95 GGUUawn Givw. Mistiuwpa Onlulo lA W tA9
61988, Advance Machine Company
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

I
INTRODUCTION
This manual has been prepared to help you get
the most from your PACEMAKER/MATADOR. Read
it thoroughly before operating the machine;
A SAFETY'- PRECAUTIONS
OWARNING
00 NOT USE THIS MACHINE IN AREAS. WHERE FLAMMABLE
LIQUIDS OR VAPORS ARE PRESENT.
^.._.
AWARNING
DISCONNECT POWER FROM-MACHINE BEFORE ATTEMPTING
ANY SERVIGE OR-MAINTENANCE WORK.
OWARNiNG
00 NOT EXPOSE TO RAIN.`STORE INDOORS.
NOTE:
For additional information, cautions and
warnings, read operator's manual before running
machine.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

I"
AWARNING
THIS MACHINE MUST BE PROPERLY GROUNDED TO PROTECT THE OPERATOR
FROM ELECTRICAL SHOCK. READ TEE SAFETY INSTRUCTIONS BELOW BEFORE
OPERATING THIS MACHINE.
115 or 120 VOLT MACHINES HAVE
THIS KIND OF 3 PRONG PLUG AT
THE END OF A 3 WIRE ELECTRICAL
CORD.
THE GROUNDING PIN•ON
THIS PLUG GROUNDS THE MACHINE
WHEN IT IS PLUGGED INTO A 3
PRONG OUTLET. .
A GROUNDING ADAPTER MUST BE
INSTALLED, AS SHOWN HERE^IF
ONLY 2 PRONG OUTLETS ARE
AVAILABLE.
THE OUTLET BOX
MUST BE GROUNDED AND THE
GROUNDING TAB (OR WIRE) ON THE
ADAPTER MUST BE INSTALLED
UNDER THE HEAD OF THE SCREW IN
THE CENTER OF THE OUTLET COVER.
GROUNDING ADAPTERS FOR 115 OR
120 VOLT PLUGS ARE AVAILABLE
AT MOST HARDWARE STORES.
NOTEt
GROUNDING ADAPTERS ARE NOT
APPROVED FOR USE IN CANADA. NOT.
240 VOLTMACHINESHAVE THIS!
<-TYP=:OF3PRONG PLUG, AT;-THB.
^
END OF
A3 NIRE ELSCTRICAL"'--
CORD. :;TH8,GROUNDINGPIR ON
2^0 YOLT
THISPL'UG GROUNDSrTBEMACBINE,,..
r
WHEN 'IT 13 PLUGGEO . INTO ^A 3
It
140 VOLT PLUGS. ..
"
.
(ROUND)
3 PRONG GROUNDED
OUTLET
".GROUNDED
OUTLET
BOX
ADAPTERS ARE NOT AVAILABLE FOR
GROUNDING PIN
REPLACE THE PLUG IF THE GROUNDING PIN IS DAMAGED OR BROKEN.
s
THE GREEN (OR GREEN AND YELLOW ) WIRE IN THE CORD IS THE GROUNDING
WIRE.
WHEN REPLACING A PLUG, THIS WIRE MUST BE ATTACHED TO THE
GROUNDING PIN ONLY.
- ,
^
EXTENSION CORDS CONNECTED TO THIS M1(CHINE SHOULD BE 12 GAUGE, 3
WIRE CORDS WITH 3 PRONG PLUGS AND OUTLETS. DO NOT,USE EXTENSION
CORDS MORE THAN 50 FT. (15 M) LONG.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

PREPARING THE MACHINE FOR USE
Attaching the Scrub Brush or Pad Holder
oth the scrub brush
'pad holder are attached
in the same manner. Align lugs with correspond-
ing slots and turn brush or pad holder to lock
in place.
Electrical Cable
Unwrap cable aod plug into proper outlet as
covered in electrical section under warning and
cautions.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

Spray Buff/Mister (optional)
i chemical bottle (2 qts.) with appropriate
chemical.
Check nozzle on machine base for
clogs and ensure proper aiming of mist.
Pressurize bottle by pumping hand lever.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

J
C7, -s
n
N r-.
m o 0
1
0
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

44
OPERATING THE PACEMAKER/MATADOR
With the machine prepared as covered in the pre-
vious section, you are ready to operate the
Pacemaker/Matador.
1)
Handle positioner is located on handle at
operator's right.
Pull on lever to unlock
handle.
Adjust handle lever as required and
release lever.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

1
2)
With both hands- on machine', push handle lock
button with forefinger of left hand. Twist
grips forward to start motor.
3)
Machine will move to the operators right and
left as the operating handle is raised and
lowered - Raise to go right - Lower to go
left.
AWARNING
Lateral,-movement* requires only slight raisirtg
.and loweringv-- exaggerated movement of handle
could cause lossof control.
OPERATING TIPS
1.
Work. away from plug outlet to keep cord from
interfering with machine operation.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

NA
AFTER USING THE PACEMAKER/MATADOR
1.
Flush spray buff system with warm water.
Remove pad holder or brush from machine for
separate storage. Never store machine with
pad holder or brush on machine.
2. Wash scrub brush and store separately.
3.
Wrap cable around cord hooks.
_
Wipe entire machine with clean damp cloth -
wipe underside of brush'housing after wet
use..
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

Maintenance of PacemakerAatador .
AWARNING
Disconnect power from machine before attempting
any service or mainteance work.
Circuit Breaker (High Speed Matador) - Designed
to protect motor rom damage by overload condi-
tion.
Normally, trippi.ng of circuit breaker is
caused by one or more of the following condi-
tions:
- Loaded pad when spray cleaning, scrubbing or
polishing
- Excessive use of material when spray cleaning
- Too-aggressive,pad for operation
- Use of other than soft-touch brush for carpet
shampooing.
-
Too little; or absence of, solution when sham-
pooing or bonnet cleaning carpet
4: :
When cause of circuit breaker tripping is deter-
mined, remedy and re-set external button by push-
ing in to position where it doesn't return,
time_'for cooling and try`again.
NOTE:
Tf button does not stay pushed in, ailow
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

1
Drive Belt (Matador)"- This belt requires no
main enance under normal circumstances, however,
after a few weeks it may become "seated" and
loosen slightly.
If this should.happen and the
belt should slip, it will become apparent by a
noise which resembles that of a dry bearing.
To tighten belt, turn phillips head screwdriver
in bolt at rear, in increments of one-half turns
until noise is eliminated.
Should belt require replacement,'follow direc-
tions printed on underside of plate beneath ma-
chfne.
This operation is best performed by your
AUTHORIZED ADVAN=GE.SERVICING DISTRIBUTOR, and
for certain, Advance replacement parts are
recommended.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000

Qd
Carbon Motor Brushes {Hi h S
eed Matador) - Will
gp
require.replacement_after approximately 700
hours of operation. Contact your AUTHORIZED
FACTORY SERVICING DISTRIBUTOR for this service.
Unplug the cable and wrap it around cord storage
hooks.
Store machine in safe place with handle upright
for minimum storage space use.
CLEAN AND INSPECT FOR DAMAGE„the entire machine
and all accessories before storing.
TROUBLE SHOOTING TIPS
SWIRLS.ON FLOOR AFTER SCRUBBING
Floor not clean; working too fast.
Incorrect solution. '
Area not properly pre-swept.
Improper pads or br.ushes.
SWIRLS ON FLOOR AFTER DRY BUFFING
Improper pads orbrushes.
Area not:properly,pre-swept.
Working too fast.
Finish.too sof.t. _ ._ ,; ..
CIRCLES DN:FLOOR
Machine standing still with brush running.
FLOOR FINISH REMOVED
Improper pad...too aggressive.
Solution too4strong.
Source: https://www.industrydocuments.ucsf.edu/docs/pzmx0000