Advantech POC-S197 User manual

User Manual
POC-S197/S177/S157

POC-S197/S177/S157 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2010
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Part No. 2008S19700 Edition 1
Printed in Taiwan October 2010

iii POC-S197/S177/S157 User Manual
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
!Consult the dealer or an experienced radio/TV technician for help.
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
–This equipment is a source of electromagnetic waves. Before use please,
make sure that there are not EMI sensitive devices in its surrounding which
may cause malfunction.
Manufacturer
Advantech Co., Ltd.
No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114, R.O.C.
TEL: [phone]
Distributed in Europe by:
Advantech Europe GmbH Kolberger Straße 7
D-40599 DÜsseldorf, Germany
Tel: [phone]
Fax: [phone]
Visit the Advantech websites at www.advantech.com or www.advantech.com.tw if
you need more information.

POC-S197/S177/S157 User Manual iv
Instructions for the User
The document combines text and illustrations, providing a comprehensive overview
of the system. The information is presented as sequential steps of action, allowing
the user to learn directly how to use the device.
The text provides explanations and instructs the user step by step in the practical use
of the product, with short, clear instructions in easy-to-follow sequence.
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
Note! Notes provide optional additional information.

v POC-S197/S177/S157 User Manual
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
!POC-S197/ S177/ S157 series Point of Care Terminal
!CD-ROM disc-"Drivers, User's manual and Utilities"
!Mounting kits and packet of screws
!External DC adapter (Manufacturer: SINPRO Model no.: HPU100-107)
Safety Instructions
1. Strictly follow these Instructions for Use, please read these safety instructions
carefully.
2. Remember to keep this User's Manual for later reference, and any use of the
product requires full understanding and strict observation of all portions of these
instructions. Observe all WARNINGS and CAUTIONS as rendered throughout
this manual and on labels on the equipment.
3. Repair of the device may also only be carried out by trained service personnel.
Advantech recommends that a service contract be obtained with Advantech
Service and that all repairs also be carried out by them. Otherwise the correct
functioning of the device may be compromised.
4. If one of the following situations arises, get the equipment checked by service
personnel:
! The power cord or plug is damaged.
! Liquid has penetrated into the equipment.
! The equipment has been exposed to moisture.
! The equipment does not work well, or you cannot get it to work according to
the user's manual.
! The equipment has been dropped and damaged.
! The equipment has obvious signs of breakage.
Warning! No user serviceable parts inside, refer servicing to qualified personnel.
Only the accessories indicated on the list of accessories above have
been tested and approved to be used with the device. Accordingly it is
strongly recommended that only these accessories be used in conjunc-
tion with the specific device. Otherwise the correct functioning of the
device may be compromised.
Warning! Because of the danger of electric shock, never remove the cover of a
device while it is in operation or connected to a power outlet.

POC-S197/S177/S157 User Manual vi
5. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning and keep this equip-
ment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage. For plug-in equipment, the power outlet socket must
be located near the equipment and must be easily accessible.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet. Position the power cord so that people cannot
step on it. Do not place anything over the power cord. If the equipment is not
used for a long time, disconnect it from the power source to avoid damage by
transient over voltage.
8. If your computer clock does not keep the correct time or the BIOS configuration
resets to default, the battery has no power.
9. Improper installation of VESA mounting can result in serious personal injury!
VESA mount installation should be done by a professional technician; please
contact the service technician or your retailer if you need this service. Detailed
procedures are specified in Appendix C.
10. CLASSIFICATION:
1). Supply Class I adapter
2). No applied part
3). IPX1
Caution! To avoid short-circuiting and otherwise damaging the device, do not
allow fluids to come in contact with the device. If fluids are accidentally
spilled on the equipment, remove the affected unit from service as soon
as possible and contact the service personnel to verify that patient
safety is not compromised.
Caution! To prevent overheating, do not cover the openings and place the device
in direct sunlight or near radiant heaters.
Caution! Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20° C (-4° F) or above 60° C (140° F). this
may damage the equipment.
Caution! Do not replace battery yourself. Please contact a qualified technician or
your retail.
The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacture.
Discard used batteries according to the manufacturerís instructions
Caution! The battery charging indicator is not included in this device. It shall be
added to the end system assembly and be shown there.

vii POC-S197/S177/S157 User Manual
4). Continuous Operation
5). Not AP or APG category
11. Environmental protection: follow national requirements to dispose of unit.
12. Maintenance: to properly maintain and clean the surfaces, use only the
approved products or clean with a dry applicator.
13. Make sure the user does not contact SIP/SOPs and the patient at the same
time.
14. When networking with electrical devices, the operator is responsible for ensur-
ing that the resulting system meets the requirements set forth by the following
standards:
–EN 60601-1 (IEC 60601-1)
Medical electrical equipment
Part 1: General requirements for safety
–EN 60601-1-1 (IEC 60601-1-1)
Medical electrical equipment
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for Medical electrical systems
–EN 60601-1-2 (IEC 60601-1-2)
Medical electrical equipment
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compatibility; Requirements and tests
15. Accessory equipment connected to analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part
or signal output part is configuring a medical system, and is therefore, responsi-
ble that the system complies with the requirements of the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment out-
side of the patient environment. If in doubt, consult the technical services
department or your local representative.
Warning! This device is not suitable for use in the presence of a flammable anes-
thetic mixture with air, oxygen, nitrous oxide, or for life support systems.
Caution! When servicing the device, always use replacement parts that are quali-
fied to Advantech standards. Advantech cannot warrant or endorse the
safe performance of third-party replacement parts for use with our medi-
cal devices.

POC-S197/S177/S157 User Manual viii

ix POC-S197/S177/S157 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
Table 1.1: Touchscreen Specifications........................................ 4
1.3 LCD Specifications.................................................................................... 4
1.4 Dimensions ............................................................................................... 5
Figure 1.1 Dimensions of the POC-S197 .................................... 5
Figure 1.2 Dimensions of the POC-S177 .................................... 5
Figure 1.3 Dimensions of the POC-S157 .................................... 6
Figure 1.4 POC-S197 front panel ................................................ 6
Figure 1.5 POC-S177/S157 front panel....................................... 7
Figure 1.6 POC-S197/S177/S157 back I/O ................................. 7
1.5 Point-of-Care Terminal Cleaning and Disinfecting .................................... 8
Chapter 2 System Setup.......................................9
2.1 A Quick Tour of the POC-S1x7 ............................................................... 10
Figure 2.1 Front view of the POC-S177/S157 ........................... 10
Figure 2.2 Front view of the POC-S197..................................... 10
Figure 2.3 Rear view of the point of care terminal ..................... 11
2.2 Installation Procedures............................................................................ 11
2.2.1 Connecting the Power Cord........................................................ 11
Figure 2.4 Connecting the power cord....................................... 12
2.2.2 Connecting the Ground pin ......................................................... 12
Figure 2.5 Equipotential terminal pin ......................................... 12
Figure 2.6 Grounding cable with connector ............................... 13
2.3 Running the BIOS Setup Program .......................................................... 13
2.4 Installing System Software...................................................................... 13
2.5 Installing the Drivers................................................................................ 14
Figure 2.7 The file directory on "Drivers and Utilities" CD-ROM 14
Chapter 3 Chipset and Graphics Setup ............15
3.1 Introduction ............................................................................................. 16
3.1.1 Chipset........................................................................................ 16
3.1.2 Display Memory .......................................................................... 16
3.1.3 DVI-I............................................................................................ 16
3.1.4 Display Types ............................................................................. 16
3.2 Installation of Chipset Driver ................................................................... 16
3.2.1 Installation for Windows XP ........................................................ 17
Chapter 4 Audio Interface ..................................23
4.1 Introduction ............................................................................................. 24
4.2 Installation of Audio Driver ...................................................................... 24
4.3 Installation for Windows 2000/XP ........................................................... 25
4.4 Further Information.................................................................................. 26
Chapter 5 PCI Express Ethernet Interface ........27
5.1 Introduction ............................................................................................. 28

POC-S197/S177/S157 User Manual x
5.2 Installation of Ethernet Driver.................................................................. 28
5.2.1 Installation for Windows XP ........................................................ 28
5.3 Further Information ................................................................................. 30
Chapter 6 Touch Panel Interface....................... 31
6.1 Introduction ............................................................................................. 32
6.2 Installation of Touch Panel Driver ........................................................... 32
6.2.1 Installation for Windows XP ........................................................ 32
6.3 Further information.................................................................................. 36
Chapter 7 Utilities and Hot Fixes ...................... 37
7.1 Introduction ............................................................................................. 38
7.2 Wakeup by External USB Device at S3 Resume (Wakeup) ................... 38
7.2.1 Installation for Windows XP ........................................................ 38
7.3 Windows Audio Volume Application ....................................................... 38
Appendix A Windows Display Hot Key Function 39
A.1 Windows Display Hot Key Function ........................................................ 40
Appendix B Description of Connectors............... 41
B.1 Description of Connectors....................................................................... 42
Figure B.1 Top side global view of POC-S1x7 motherboard indi-
cates connector locations........................................ 42
Figure B.2 Bottom side global view of POC-S1X7 motherboard in-
dicates connector locations ..................................... 43
Figure B.3 Top side global view of POC-S1X7 IO indicates con-
nector locations ........................................................ 44
Figure B.4 Top side global view of POC-S1X7 2nd I/O indicates
connector locations .................................................. 44
Appendix C VESA Mounting ................................. 45
C.1 Install VESA Mounting ............................................................................ 46

Chapter 1
1General Information

POC-S197/S177/S157 User Manual 2
1.1 Introduction
The S197/ S177/ S157 is a multimedia Intel® CoreTM2 Duo processor-based mobile
computer that is designed to serve as a Point of Care terminal (POC). It is a PC-
based system with 19”/17”/15” color TFT LCD display, a single DVI-I Port, dual on-
board 10/100/1000 PCI-E Ethernet controllers, a single COM port, quad USB 2.0
ports and a 24-bit stereo audio controller. With a built-in 2.5” HDD drive, the S197/
S177/ S157 is as slim and user-friendly as a notebook computer and operates with
low audible noise. For system integrators, this silent, compact, mobile and highly
integrated multimedia system lets you easily build a Point of Care terminal into your
applications. The low audible noise of S197/ S177/ S157 makes it an ideal and safe
point of care solution for patients and hospital practitioners.
The high contrast ratio of S197/ S177/ S157 makes it a perfect image terminal for
PACS and DICOM applications. The S197/ S177/ S157 is a reliable solution to your
application's processing requirements.
1.2 Specifications
General
!Dimensions (W x H x D):
–POC-S197: 472 x 416 x 111 mm (18.58" x 16.38" x 4.37")
–POC-S177: 436.5 x 376.5 x 91.4 mm (17.18" x 14.82" x 3.59")
–POC-S157: 418 x 342 x 89.3 mm (16.46" x 13.46" x 3.51")
!Weight:
–POC-S197: (w/o battery) 8.1 kg
–POC-S177: (w/o battery) 7.1 kg
–POC-S157: (w/o battery) 5.4 kg
!Power supply:
–DC model: 100 watts max External DC Adapter- (Manufacturer: SINPRO Inc.
Model no.: HPU100-107) used within POC-S197/S177/S157
–Input voltage: 100 ~ 240 VAC, 47-63 Hz, 1.25 ~ 0.5 A
–Output voltage: +18 VDC, 5.55 A max.
!Disk drive housing: Space for one 2.5" SATA HDD
!Entire system: IPX1 compliant
Hardware
!CPU: Intel® Core 2 Duo® processor Ultra-low Voltage SU9300 1.2 GHz
!BIOS: SST 8 Mbit SPI Serial Flash BIOS.
!Chipset: Intel® GS45 Express Chipset with 82801IUX I/O Controller Hub
(ICH9M-SFF)
!Front side bus: 800 MHz
!RAM: 204-pin, DDR3, SODIMM slots x 2 (max. 4 GB), Unbuffered Non ECC,
capacity maximum to 4 GB
!SATA interface: SATA x 1. Supports one SATA device.
!Serial ports: RS-232 ports x 2; they are both compatible with 16C550 UARTs.
COM1 has optical isolation;
!Universal serial bus (USB) port: USB 2.0 ports x 5 (3 external, 2 internal)
!Expansion slot: Mini PCI/33MHz slot x 1, Mini PCI-E(2.5 Gb/s) slot x 1

3 POC-S197/S177/S157 User Manual
Chapter 1 General Information
!Watchdog timer: Supports super I/O embedding watchdog function. Automati-
cally generates system reset when the system stops due to a program error.
!CMOS battery (BIOS): 3.0 V @ 195 mA lithium battery
!Backup battery (Optional): 11.1 V @ 6300 mAh lithium battery
–Formosan United Corporation or JOULES MILES CO., LTD./ POC-S1X7
Display interface
!SDVO interface: PERICOM PI3VDP411LS Digital Video Level Shifter from AC
coupled digital video input to a DVI/HDMI transmitter
!Display resolution: Supports 24-bit digital output (DVI-I port) resolutions up to
1920 x 1200. (WUXGA)
!Display type: Simultaneously supports CRT
Audio function
!Chipset: Realtek ALC888, compliant with Intel HDA.
!Audio controller: 24-bit codec, full-duplex stereo codec
!Audio interface: Microphone-in, Line-out
Ethernet interface
!Chipset: INTEL_82574L PCI express high performance Gigabit Ethernet con-
troller
!Ethernet interface: Gigabit Ethernet ports x 2, fully integrated Gigabit Ethernet
Media Access Control (MAC) and Physical Layer (PHY) functions, and each
provides a standard IEEE 802.3 Ethernet interface for 10/100/1000 Mbps.
Optional modules
!Memory: 1GB/2GB, DDR3-800 MHz SODIMM
!HDD: 2.5" SATA HDD
!Mini PCI WLAN module: 802.11a/b/g WLAN
!Mini PCI-E WLAN module: 802.11b/g/n WLAN
Environment
!Temperature: 0 ~ 40° C (32 ~ 104° F) (Operating)
!Relative humidity:
–-20 ~ 60° C (Storage)
–-20 ~ 60° C (Transportation)
–Humidity 10 ~ 95%@40° C (non-condensing)
–to 95% (non condensing) (Storage)
–to 95% (Transportation)
–Operating atmospheric pressure: 700 ~ 1060 hPa
–Storage atmospheric pressure: 700 ~ 1060 hPa
–Transportation atmospheric pressure: 700 ~ 1060 hPa
!Shock: 20 G, half sine, 11 msec duration
!Vibration: 0.047 double amplitude displacement ( 5 ~ 32 Hz), 2 G Peak (32 ~
500 Hz )
!Power MTBF: 100,000 hrs
!Altitudes: Operational: 6,000 feet; Shipping : 40,000 feet
!Certifications:
–EMC: CE, FCC approved

POC-S197/S177/S157 User Manual 4
–Safety: UL60601-1 and EN60601-1 approved.
This device bears the CE label in accordance with the provisions of the EMC Direc-
tive 89/336/EMC and the Low Voltage Directive 73/23/EEC.
Touchscreen (optional)
Optional modules
!Memory: 1 GB/2 GB, DDR3 800 MHz DRAM
!HDD: 2.5" SATA HDD
!Touchscreen: Analog resistive
1.3 LCD Specifications
POC-S197
!Display type: 19" TFT LCD.
!Resolution: 1280 x 1024
!Colors: 16.7 M (8 bits/color)
!Dot size (mm): 0.294 x 0.294
!Viewing angle: 178° x 178°
!Luminance: 300 cd/m2
!Contrast ratio: 1300 : 1
!LCD MTBF: 50,000 hours
!Backlight lifetime: 50,000 hours
POC-S177
!Display type: 17" TFT LCD
!Resolution: 1280 x 1024
!Colors: 16.7 M (8 bits/color)
!Dot size (mm): 0.264 x 0.264
!Viewing angle: 140° x 130°
!Luminance: 300 cd/m2
!Contrast ratio: 500 : 1
!LCD MTBF: 50,000 hours
!Backlight lifetime: 50,000 hours
POC-S157
Table 1.1: Touchscreen Specifications
Type Analog Resistive
Resolution Continuous
Light Transmission 75%
Controller RS-232 interface (uses COM6)
Power Consumption +5 V @ 200 Ma
Software Driver Supports Windows 2000,Windows XP
Durability (touches in a lifetime) 30 million
Note! The Point of Care Terminal with the optionally installed touchscreen will
share COM6. Once the touchscreen is installed, COM6 cannot be used
for other purposes.

5 POC-S197/S177/S157 User Manual
Chapter 1 General Information
!Display type: 15" TFT LCD.
!Resolution: 1024 x 768
!Colors: 262,144 (6 bits/color)
!Dot size (mm): 0.264 x 0.264
!Viewing angle: 120°
!Luminance: 350 cd/m2
!Contrast ratio: 400 : 1
!LCD MTBF: 50,000 hours
!Backlight lifetime: 50,000 hours
1.4 Dimensions
Figure 1.1 Dimensions of the POC-S197
Figure 1.2 Dimensions of the POC-S177

POC-S197/S177/S157 User Manual 6
Figure 1.3 Dimensions of the POC-S157
Figure 1.4 POC-S197 front panel
A. Power Switch
B. Touchscreen Light Indicator
C. Touchscreen Status Control
D. Volume Up/Down
E. Brightness Increase/Decrease
F. Read Light Control
A B C D E F

7 POC-S197/S177/S157 User Manual
Chapter 1 General Information
Figure 1.5 POC-S177/S157 front panel
A. Audio Control Button
B. Power Light
C. Brightness Control Button
Figure 1.6 POC-S197/S177/S157 back I/O
A. 4-pin mini-DIN DC connector
B. USB 2.0 ports x 3
C. DVI-I port
D. Isolated 10/100/1000 Mbps Ethernet interface x 2 (RJ-45)
E. Isolated RS-232 COM 2 port
F. Isolated RS-232/422/485 COM 1 port (by jumper selection)
A B C
A B C D E F G

POC-S197/S177/S157 User Manual 8
G. Power sw itc h
1.5 Point-of-Care Terminal Cleaning and
Disinfecting
During normal use of the POC (Point-of-Care Terminal) the device may become dirty
and should be regularly cleaned.
Steps:
1. Prepare cleaning agent per manufacturer’s instructions or hospital protocol.
2. Wipe the POC with a clean cloth that has been moistened in the cleaning solu-
tion.
3. Wipe thoroughly with a clean cloth.
Cleaning agent list: chemical disinfectants which have been tested on the POC.
No Cleaning Agents
1 Cidex
2 Isopropyl alcohol
3 Green tinctured soap
4Windex
5 Alcohol
6 Alcohol 70%
7 Chloride 1000PPM
8 Incidin plus
9 Incidin liquid
10 Mikrozid liquid
Caution! ! Do not immerse or rinse the POC or its peripherals. If you acciden-
tally spill liquid on the device, disconnect the unit from the power
source. Contact your Biomed Department regarding the continued
safety of the unit before placing it back in operation.
! Do not spray cleaning agents on the chassis.
! Do not use disinfectants that contain phenol. Do not autoclave or
clean the POC or its peripherals with strong aromatic, chlorinated,
ketone, ether, or Esther solvents, sharp tools or abrasives. Never
immerse electrical connectors in water or other liquids.

Chapter 2
2System Setup

POC-S197/S177/S157 User Manual 10
2.1 A Quick Tour of the POC-S1x7
Before you start to set up the POC-S177/S157, take a moment to become familiar
with the locations and purposes of the controls, drives, connections and ports, which
are illustrated in the figures below.
When you place the POC-S177/S157 upright on the desktop, its front panel appears
as shown in Figure 2.1.
Figure 2.1 Front view of the POC-S177/S157
When you place the POC-S197 upright on the desktop, its front panel appears as
shown in Figure 2.2.
Figure 2.2 Front view of the POC-S197
When you turn the Point-of-Care terminal around and look at its rear cover, the
sunken white dot section is at the bottom of the panel PC, as shown in Figure 2.3.
(The I/O section includes white dot ports, including serial ports, DVI port, the Ethernet
port, USB ports, the DC power adapter jack, and so on.)