Advantech ADAM-4562 User manual

1
ADAM-4562
1 port Isolated USB to RS-232 Converter
User’s Manual

2
1.1 Introduction
Advantech’s ADAM-4562 allows PC users to connect their serial devices to systems that
use USB interface. By attaching the ADAM-4562 to a PC, it will no longer be necessary
to open the chassis or turn off the PC to install the hub. With the ADAM-4562, the user
instantly gets one extra high-speed RS-232 ports which is the Full Modem control
signals. In addition, since the power is derived from the USB port, there are not any
cumbersome power adapters. This makes the ADAM-4562 especially suitable for printers,
POS system and industrial control devices.
Compliant with USB v1.1, the ADAM-4562 features a lot of powerful functions such as
high-speed 115.2 Kbps, support for various operating systems and Full Modem control
signal. By simply plugging in a USB hub, the ADAM-4562 eliminates configuration
issues associated with expensive, antiquated card solutions. This eliminates the need to
remove the PC cover and or to reboot the operating system during installation. The user
only installs the driver, and follows the on-screen instructions. This reduces a lot of
programming time.
The USB interface, now standard on virtually all new PCs, offers significant advantages
over earlier bus types. A signal USB interface can connect up to 127 devices at data rates
up to 12 Mbps. This kind of easy and convenient connectivity means that your network
can grow with your needs.
1.2 Features
zOutput type: Full compliance with USB v1.1specifications
zTransmission speed up to 115.2Kbps
zFull-duplex transmitter (TX) and receiver (RX);
Six Modem control pins RTS, CTS, DTR, DSR, DCD, and RI)
zIsolation protection 2,500 Vdc provided
zNo external power supply necessary; the ADAM-4562 derives its power from the
USB port
zPlug-and play installation
zHot swap function supported
zDrivers for Windows 98/2000/XP

3
1.3 Specification
zCompatibility: USB v1.1 standard
zInterface: Network: USB
Serial: RS232
zConnector: Network: USB-type A connector (type A to type B cable provided)
Serial: DB-9 serial connectors
zTransmission speed: 75bps to 115.2Kbps
zPower Consumption : 155mA@5V(typical)
220mA@5V(Max.)
zParity bit: Odd, Even, Mark, Space, None
zData bit: 5, 6, 7, 8
zStop bit : 1, 1.5 , 2
zError detection: Parity error, frame error, serial break
zIsolation protection: 2,500 Vdc
zCase: ABS with captive mounting hardware
zOperating temperature: 0° to 70° C
zStorage Temperature: -25° to 80° C
zOperating Humidity: 20% to 95% (non-condensing)
zStorage Humidity: 0% to 95% (non-condensing)
•
1.4 Package Checklist
zADAM-4562
zADAM series CD
zOne Type A to Type B USB cable
zNYLON DIN-rail Mounting Adapter
zSECC Panel Mounting Bracket
If you have any questions about USB standard, please refer to the web
Site: www.usb.org

4
2 Hardware Installation
2.1 Network Architecture
Traditional serial port communication uses a COM port board that slides into one of the
slots at the back of your PC. With the ADAM-4562, you can access the COM port from
USB ports. The ADAM-4562 can be integrated into the network architecture of any
protocol.
Note: all the operating systems on your host must support USB v1.1 or above standard,
such as Windows 98/2000/XP. USB devices are used in “Master-Slave” architecture.
Before you useADAM-4562, you must determine the master PC. The following
illustration shows the network architecture:
Figure 2-1: Network Architecture
2.2 Network Connection
When using the ADAM-4562, you will simply plug one end of USB cable (included in
package) into ADAM-4562, and the other end into the USB hub or your host PC.

5
2.3 Serial Connection
The model of the ADAM-4562 has one RS-232 DTE connector for connecting serial
ports on the bottom of module.
Note: In USB v1.1 standard, if you have used the COM3, COM4…..COMn of host PC.
When you plug ADAM-4562 in the host PC, theCOM port will be COMn+1.
Figure 2-1 RS-232 Terminal (DTE) connections
2.4 Jumper Settings
Grounding is one of the most important issues for our system. Just like Frame
Ground of the computer, this signal offers a reference point of the electronic circuit
inside the computer. If we want to communicate with this computer, both Signal
Ground and Frame Ground should be connected to make a reference point of
each other’s electronic circuit. Generally speaking, it is necessary to install an
individual grounding bar for each system, such as computer networks, power
systems, telecommunication networks, etc. Those individual grounding bars not
only provide the individual reference point, but also make the earth a our ground!
Jumper JP1 allows choosing the ground setting. If jumpers JP1 is set as following, the
pins 1 & 2 are closed and it means the ground is connected to the shell of DB9 connector.
On the other words, the pins 2 & 3 are closed and it means the ground is floating
ground is connected to ground is floating
the shell of DB9 connector
(default setting)

6
3. Driver and Utility Installation
In order to use a PC to control serial devices connected to the ADAM-
4562, you must first have a host running Windows 98/2000/XP.
Following are the installation instructions to set up the ADAM-4562.
1. Insert the ADAM-4562 Driver utility diskette into the CD drive
(e.g. E:\) on the host PC.
2. Plug in the USB connector of ADAM-4562 then system will detect the new device
automatically and show the hardware wizard. Please choose the item Install from a
list or specific location if it is the first use on this PC.

7
3. Indicate the location to specify the installation path like as
E:\ADAM-4562/driver/98_2k_XP/ then it will auto-select the suitable driver to
install for your system. After you have specified the installation path, click the Next
button.
4. It will has the dialog window for this installation, please click the button of
Continue Anyway to start set up

8
5. It shows the following window when the installation is completed and use also
can find the com port of ADAM-4561/4562 on Device manager