Advantech IDK-1110P-50XGB1 User manual

User Manual
IDK-1110P-50XGB1
10.4” XGA Industrial Display Kit
with Projected Capacitive Touch
Solution

IDK-1110P-50XGB1 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2022
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
AMI is a trademark of American Megatrends Inc.
IBM and PC are trademarks of International Business Machines Corporation.
Intel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corpo-
ration.
WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are properties of their respective owners.
Part No. 2006111050 Edition 1
Printed in China February 2022

iii IDK-1110P-50XGB1 User Manual
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.

IDK-1110P-50XGB1 User Manual iv
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v IDK-1110P-50XGB1 User Manual
Contents
Chapter 1 Overview...............................................1
1.1 General Description .................................................................................. 2
1.2 Specifications............................................................................................ 2
1.2.1 LCD Panel..................................................................................... 2
1.2.2 Touch Screen................................................................................ 2
1.2.3 Environment.................................................................................. 2
1.3 Mechanical Characteristics ....................................................................... 4
Chapter 2 LCD Display .........................................5
2.1 Functional Block Diagram ......................................................................... 6
2.2 Absolute Maximum Ratings ...................................................................... 6
2.2.1 TFT LCD Module .......................................................................... 6
2.2.2 Backlight Unit ................................................................................ 6
2.3 LCD Electronics Specification ................................................................... 7
Table 2.1: Power Specifications .................................................. 7
2.4 Backlight Unit ............................................................................................ 9
Table 2.2: Backlight Driving Conditions....................................... 9
2.5 Input Terminal Pin Assignment ............................................................... 11
2.5.1 TFT LCD MODULE..................................................................... 11
Table 2.3: Pin Description ......................................................... 11
Table 2.4: Backlight Pin Assignment ......................................... 12
2.6 Color Data Input Assignment .................................................................. 14
Table 2.5: Color Data Input Assignment.................................... 14
Table 2.6: Color Data Input Assignment.................................... 15
2.7 Interface Timing ...................................................................................... 16
2.7.1 Input Signal Timing Specifications .............................................. 16
Table 2.7: Display Timing Specifications................................... 16
2.8 Power On/Off Sequence ......................................................................... 19
Table 2.8: Timing Specifications:............................................... 19
2.9 The Input Data Format............................................................................ 20
2.10 Scanning Direction.................................................................................. 21
Chapter 3 Touchscreen and Touch Controller.23
3.1 Mechanical Dimensions and Construction .............................................. 24
3.1.1 General ....................................................................................... 24
3.1.2 Mechanical Performance: ........................................................... 24
3.2 Electrical Specifications .......................................................................... 24
3.2.1 Specifications.............................................................................. 24
3.2.2 Pin Assignment and Description ................................................. 25
3.3 Typical Optical Characteristics................................................................ 25
Appendix A LCD Optical Characteristics .............27
A.1 Test Conditions ....................................................................................... 28
A.2 Optical Specifications.............................................................................. 28
Appendix B Safety Precautions ............................31
B.1 Assembly and Handling Precautions ...................................................... 32

IDK-1110P-50XGB1 User Manual vi
B.2 Storage Precautions ............................................................................... 32
B.3 Other Precautions ................................................................................... 33

Chapter 1
1Overview

IDK-1110P-50XGB1 User Manual 2
1.1 General Description
The Advantech IDK-1110P-50XGB1 comes with a 10.4" industrial grade LCD display
with projected capacitive (PCAP) touch with low power consumption. This display is
ideal for embedded applications that necessitate maximum flexibility for mechanical
design.
1.2 Specifications
1.2.1 LCD Panel
Display Size: 10.4", 4:3
Resolution: 1024x768
Display Mode: Normally Black (Full view)
Viewing Angle (Horizontal/Vertical): 176°/176°
Brightness: 500 cd/m2
Contrast Ratio: 1000:1
Response Time (ms): 25
Colors: 262k (6bit) / 16.2M (8bit)
LCD Nominal Input Voltage: 3.3V
Backlight Input Voltage: 12V
Power Consumption: 7.47W (white pattern)
Signal Interface: LVDS
Weight: 320 g/ 0.7 lbs
Dimensions (W x H x D): 225 x 176 x 8.7 mm (0.73 x 0.57 x.028 in)
1.2.2 Touch Screen
Touch Screen: Projected Capacitive (PCAP)
Light Transmission: 90  3%
Interface: USB
Surface Treatment: Clear
Black Print: Yes
1.2.3 Environment
Operating Temperature: -20 ~ 70 °C (-4 ~ 158 °F)
Storage Temperature: -30 ~ 80 °C (-22 ~ 176 °F)
Note!  90% RH Max.
 Wet-bulb temperature should be 39 °C /102 °F Max.
No condensation.
Note! Surface temperature should be min. 0 °C (32 °F) and max. 85 ºC (185
°F) under Vcc=5.0V, fr =60Hz, typical LED string current, 25 ºC (77 °F)
ambient temperature, and no humidity control. Any condition of ambient
operating temperature, the surface of active area should be keeping not
higher than 85 ºC(185 °F).

3 IDK-1110P-50XGB1 User Manual
Chapter 1 Overview
Relative Humidity (%RH) of LCD only

IDK-1110P-50XGB1 User Manual 4
1.3 Mechanical Characteristics
Front View Unit: mm
Rear View
Note: Tolerances unless marked are ± 0.5 mm

Chapter 2
2LCD Display

IDK-1110P-50XGB1 User Manual 6
2.1 Functional Block Diagram
The following diagram shows the functional block of the 10.4" Color TFT-LCD Mod-
ule:
2.2 Absolute Maximum Ratings
2.2.1 TFT LCD Module
2.2.2 Backlight Unit
Item Symbol Min. Max. Unit Note
Power Supply Voltage VCC -0.3 3.6 [Volt] (1)
Logic Input Voltage VIN -0.3 3.6 [Volt]
Item Symbol Value Unit Note
Min. Max.
(1), (2)Converter Voltage Vi-0.3 18 [Volt]
Enable Voltage EN -0.3 5.5 [Volt]
Backlight Adjust ADJ -0.3 5.5 [Volt]
Note (1) Permanent damage to the device may occur if maximum values are
exceeded. Operation should be restricted to the conditions described
under Normal Operating Conditions.
Note (2) Specified values are for LED light bar.

7 IDK-1110P-50XGB1 User Manual
Chapter 2 LCD Display
2.3 LCD Electronics Specification
Input power specifications are as follows:
Table 2.1: Power Specifications
Parameter Symbol Value Unit Note
Min. Typ. Max.
Power Supply Voltage VCC 3.15 3.3 3.45 V (1)
Power Supply Ripple Voltage VRP - - 100 mV (2)
Rush Current IRUSH - - 4.0 A
Input Current White ICC - 505 610 mA (3)
Black - 315 380 mA
Power Consumption PL - 1.67 W
LVDS Differential Input Voltage Vid 100 - 600 mV
LVDS Common Input Voltage Vic 1.0 1.2 1,4 V
Logic High Input Voltage VIH 2.3 - VCC V
Logic Low Input Voltage VIL 0 - 0.7 V
LVDS terminating resistor RT - 100 - ohm
Note (1) The assembly should always be operated within above ranges.
Note (2) Measurement conditions:

IDK-1110P-50XGB1 User Manual 8
Note (3) The specified power supply current is under the conditions at Vcc =
3.3V, Ta = 25 ± 2 °C (77 ± 3.6 °F), fv = 60 Hz, whereas a power dissipa-
tion check pattern below is displayed.

9 IDK-1110P-50XGB1 User Manual
Chapter 2 LCD Display
2.4 Backlight Unit
The following characteristics are measured under stable condition at 25 °C (77 ° F).
Table 2.2: Backlight Driving Conditions
Parameter Symbol Values Unit Note
Min. Typ. Max.
Converter Power Supply Voltage Vi 10.8 12 13.2 V
Converter Power Supply Ripple Voltage ViRP - - 350 mV
Converter Power Supply Current Ii - 0.48 0.55 A @ Vi = 12V
(Duty 100%)
Converter Inrush Current IiRUSH - - 3.0 A
@ Vi rising
time =10ms
(Vi =12V)
Backlight Power Consumption PBL - 5.8 6.6 W @ Vi = 12V
(Duty 100%)
EN Control Level Backlight On BLON 2.5 3.3 5 V
Backlight Off 0 - 0.3 V
PWM Control Level PWM High Level E_PWM 2.5 3.3 5 V
PWM Low Level 0 - 0.15 V
PWM Noise Range VNoise - - 0.1 V
PWM Control Duty Ratio -
5 - 100 %
(2), Sugges-
tion,
@190Hz<fP
WM<1kHz
20 - 100 %
(2), @
1kHz?fPWM
<20kHz
PWM Control Frequency fPWM 190 200 20k Hz (3)
LED Life Time LL 50,000 - - Hrs (2)
Note (1) LED current is measured by utilizing a high frequency current meter
shown below:

IDK-1110P-50XGB1 User Manual 10
Note (2) At 190 ~1kHz PWM control frequency, duty ratio range is restricted from
5% to 100%.
1K ~20kHz PWM control frequency, duty ratio range is restricted from
20% to 100%.
If PWM control frequency is applied in the range from 1KHz to 20KHZ,
The "non-linear" phenomenon on the Backlight Unit may be found. So
It's a suggestion that PWM control frequency should be less than 1KHz.
Note (3) The LED lifetime is estimated data and defined as the time when it con-
tinues to operate under the conditions at Ta = 25 ± 2 º C (77 ± 3.6 °F) -
and Duty 100% until the brightness becomes ≤ 50% of its original value.
Operating LED at high temperature condition will reduce life time and
lead to color shift.

11 IDK-1110P-50XGB1 User Manual
Chapter 2 LCD Display
2.5 Input Terminal Pin Assignment
2.5.1 TFT LCD MODULE
Table 2.3: Pin Description
Pin No. Symbol Description Note
1 VCC Power supply: +3.3V -
2 VCC Power supply: +3.3V -
3 VCC Power supply: +3.3V -
4 GND Ground -
5 GND Ground -
6 GND Ground -
7 RPFI Reverse Panel Function (Display Rotation) ( 3 )
8 NC No Connection ( 4 )
9 NC No Connection ( 4 )
10 NC No Connection ( 4 )
11 SEL6/8
LVDS 6/8 bit select function control,
Low or NC -> 8 bit Input Mode
High -> 6bit Input Mode
( 3 )
12 GND Ground -
13 NC No Connection ( 4 )
14 GND Ground -
15 RX0- Negative transmission data of pixel 0 -
16 RX0+ Positive transmission data of pixel 0 -
17 GND Ground -
18 RX1- Negative transmission data of pixel 1 -
19 RX1+ Positive transmission data of pixel 1 -
20 GND Ground -
21 RX2- Negative transmission data of pixel 2 -
22 RX2+ Positive transmission data of pixel 2 -
23 GND Ground -
24 RXCLK- Negative of clock -
25 RXCLK+ Positive of clock -
26 GND Ground -
27 RX3- Negative transmission data of pixel 3 -
28 RX3+ Positive transmission data of pixel 3 -
29 GND Ground -
30 NC No Connection ( 4 )
Note (1) Connector Part No.: P-TWO 187106-30091 or STM, MSCK2407P30.D
or equivalent.
Note (2) User's connector Part No.: JAE FI-X30H(L) or equivalent.

IDK-1110P-50XGB1 User Manual 12
RPFI pin:
SEL 6/8 pin:
Note (3) "Low" stands for 0V. "High" stands for 3.3V. "NC" stands for "No Con-
nected".
Note (4) Pin8, Pin9, Pin10, Pin13,Pin30 input signals should be set to no connec-
tion or ground, this module would operate normally.
Table 2.4: Backlight Pin Assignment
Pin Symbol Description Remark
1 Vi Converter Input Voltage 12V
2 Vi Converter Input Voltage 12V
3 Vi Converter Input Voltage 12V
4 Vi Converter Input Voltage 12V
5 VGND Converter Ground Ground
6 VGND Converter Ground Ground
7 VGND Converter Ground Ground
8 VGND Converter Ground Ground
9 EN Enable Pin 3.3 V, Note (3)
10 ADJ Backlight Adjustment
PWM Dimming
(190-210Hz, Hi: 3.3VDC,
Lo: 0VDC) , Note (3)
Note (1) Connector Part No.: ACES,91208-01001-H01 or equivalent

13 IDK-1110P-50XGB1 User Manual
Chapter 2 LCD Display
Note (2) User's connector Part No.: ACES,91209-01011 or equivalent
Note (3) EN(BLON), ADJ(E_PWM) as shown below:

IDK-1110P-50XGB1 User Manual 14
2.6 Color Data Input Assignment
The brightness of each primary color (red, green, and blue) is based on the 6-bit gray
scale data input for the color. The higher the binary input, the brighter the color. The
table below provides the assignment of color versus data input.
Table 2.5: Color Data Input Assignment
Color
Data Signal
Red Green Blue
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Basic Colors
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Gray
Scale
Of
Red
Red(0) /
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Red(2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Red(61) 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Red(62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Gray
Scale
Of
Green
Green(0) /
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
Green(2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Green
(61) 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0
Green
(62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
Green
(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Gray
Scale
Of
Blue
Blue(0) /
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Blue(61) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1
Blue(62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0
Blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Note (1) 0: Low Level Voltage, 1: High Level Voltage