Advantech AIMB-785 Installation and operation manual

AIMB-785 Startup Manual 1
AIMB-785 LGA1151 Intel® Core™ i7/i5/i3 ATX with
Triple Display, DDR4, SATA III
Startup Manual
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the AIMB-785 series Rev. A1.
Part No. 2001078510
Printed in China
1st Edition
Spetember 2015
Standard Functions
• CPU: LGA1151 6th Generation Intel® Core™ i7/i5/i3/
Celeron/Pentium
• BIOS: AMI 128 Mb SPI BIOS
• Chipset: Intel® Q170 chipset
• System memory: Up to 64 GB with four 288-pin
DIMM sockets. Supports dual channel non-ECC DDR4
1866/2133
Note: Due to the inherent limitations of PC architecture, the
system may not fully detect 64 GB RAM when 64 GB RAM
is installed
• SATA interface: Six on-board Serial ATAIII connectors
support data transmission rate up to 600 MB/s. All six
SATAIII ports support Advanced Host Controller Interface
(AHCI) technology
• LPC interface: Advantech-designed LPC connector sup-
ports TPM module
• Serial ports: Six serial ports: COM1, COM2 and COM4 ~
6 are RS-232; COM3 is RS-232/422/485 with BIOS menu
options
• Parallel port: One parallel port, which supports SPP/
EPP/ECP modes
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse
• Watchdog timer: 255 sec timer level intervals
• USB 3.0/2.0: Thirteen USB ports: 1/2/3/4/13/14 are
USB3.0; others are USB2.0
Graphic Interface
• Chipset: CPU integrated graphics controller
• Display Memory: 1 GB maximum shared memory with 2
GB and above system memory installed
• Resolution: Supports DVI up to 1920 x 1200 resolution@
60 Hz refresh rate
Supports VGA up to 1920 x 1200 resolution @ 60 Hz
refresh rate
Ethernet interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1: Intel
®
I219LM; LAN2: Intel
®
I211AT
Mechanical and Environmental
• Dimensions (L x W): 304.8 x 244 mm (12” x 9.6”)
• Power supply voltage: +3.3 V, +5 V, +12 V, +5 Vsb
• Power Consumption:
Intel Core Intel I7-6700 3.4 GHz; DDR4 8 G x 4
Maximum: +3.3 V at 1.02 A, +5 V at 1.96 A, +12 V at 1.14
A, +5 Vsb at 0.08 A, -5 V at 0.03 A, -12 V at 0.06 A
• Operating temperature: 0 ~ 60° C (depending on CPU)
• Weight: 0.5 kg (weight of board)
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 AIMB-785 Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 1 Serial ATA HDD power cables
• 1 I/O port bracket
• 1 Warranty card
• 1 Startup manual
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
All manuals and user guides at all-guides.com
all-guides.com

2 AIMB-785 Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each jumper and connector.
Connector / Jumper List
Label Function
JWDT1 Watchdog Reset
LPC1 Low pin count connector for Advantech
designed LPC modules
LPT1 Parallel port supports SPP/ EPP/ECP
mode
LAN1_USB12 LAN1 / USB 3.0 port 1, 2
LAN2_USB34 LAN2 / USB3.0 port 3, 4
VGA1+COM1 VGA connector / COM connector
DVI1+DVI2 Dual DVI-D connectors
COM1
COM2
COM4
COM5
COM6
Serial port: RS-232
COM3 Serial port: COM3; RS-232/422/485
(9-pin connector)
KBMS1 Keyboard and Mouse PS/2 connector
(6-pin)
JFP3
Keyboard Lock and Power/Sleep LED
Suspend: Fast ash (ATX/ AT)
System On: ON (ATX/ AT)
System Off: OFF (AT/ATX)
JFP2 External speaker / HDD LED connector
SNMP / SM Bus connector
JFP1 Power Switch / Reset connector
JCASE1 Case Open connector
PSON1 AT(1-2) / ATX(2-3) mode selector
VOLT1 Alarm Board Power connector
JOBS1 Close: Enable OBS Alarm
Open: Disable OBS Alarm
CPUFAN1 CPU FAN connector (4-pin)
SYSFAN1 System FAN power connector (3-pin)
SYSFAN2 System FAN power connector (3-pin)
LANLED1 Front Panel LAN indicator connector
AUDIO1
AUDIO2 Audio connector (Line-out, Mic-In)
FPAUD1 Front Panel Audio pin header
USB56 USB port 5, 6
USB78 USB port 7, 8
USB910 USB port 9, 10
USB11 USB11 (Type A)
USB1314 USB3.0 13, 14
SATA1 Serial ATA1
SATA2 Serial ATA2
SATA3 Serial ATA3
SATA4 Serial ATA4
SATA5 Serial ATA5
SATA6 Serial ATA6
ATX12V1 ATX 12V Auxiliary power connector
(for CPU)
EATXPWR1
ATX 24 Pin Main power connector
(for System)
SPDIF_OUT1 Digital audio output pin header
SPI_CN1 SPI ash card pin header
JCMOS1
CMOS clear
JME1 Intel ME Enable/Disable jumper
JPCICLK1
PCI Clock selection
(1-2): 66 MHz
(2-3): 33 MHz (default)
JUSB_1 USB power source switch between +5V
and +5V_ DUAL for Rear USB ports
JUSB_2
USB power source switch between +5V
and +5V_ DUAL for On Board USB
ports
GPIO1 8 bit digital I/O connector
SMBUS1 SMBus connector
JCMOS1: CMOS and ME clear function
Pins Result
1-2 Keep CMOS data*
2-3
Clear CMOS data
* Default
12 3
12 3
*Keep CMOS data Clear CMOS data
Jumpers and Connectors Jumpers and Connectors (Cont.)
All manuals and user guides at all-guides.com

12 3
12 3
12 3
12 3
AIMB-785 Startup Manual 3
JWDT1: Watchdog timer output option
Closed Pins
Result
2-4 NC
4-6 System reset*
* Default
PSON1: ATX, AT mode selector
Closed Pins
Result
1-2 AT Mode
2-3 ATX Mode*
* Default
JUSB
Closed Pins
Result
1-2 *USB +5V_DUAL Power
2-3 USB +5V Power
* Default
The CD disc contains a driver installer program that will
lead you through the installation of various device drivers
needed to take full advantage of your motherboard.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Jumpers and Connectors (Cont.)
AT Mode 1-2 closed *ATX Mode 2-3 closed
Software Installation
Declaration of Conformity
NC 2-4 Closed *System Reset 4-6 Closed
*USB +5 V_DUAL Power USB +5 V Power
All manuals and user guides at all-guides.com

SPDIF_OUT1
FPAUD1
LANLED1
KBMS1
CPUFAN1
SYSFAN2
SYSFAN1
VOLT1
ATX12V2
EATXPWR1
PSON1
SPI_CN1
JIR1+JWDT1+JOBS1
JFP3
JFP1+JFP2
GPIO1
SMBUS1
JCASE1 JCASEOP_SW1
LPC1
CPU1
DVI1+DVI2
VGA1+COM1
USB78
LAN1_USB12 LAN2_USB34
AUDIO1
AUDIO2
PCIe x16
PCIe x4
PCIe x4 PCIe x4
PCI1
PCI2
PCI3
DIMM B2
DIMM B1
DIMM A2
DIMM A1
LPT1
COM3
COM4
COM6
COM5
COM2
USB910
USB56 USB1314
USB11
JPCICLK1
JUSB_2
JCMOS1
JME1
SATA0 SATA2 SATA4
SATA1 SATA3 SATA5
Q170
3 6 9 12
25811
PWRSW RESET
HDDLED
SNMP
JFP1
&
2 5 8 11
1 4 7 10
HDDLED
SM_BUS
SPEAKER
JFP2
&
PWRLED & KEYLOCK
12345
JFP3
4 AIMB-785 Startup Manual
Board Layout
Figure 1: Board Layout: Jumper and Connector Locations
All manuals and user guides at all-guides.com