Advantech RSB-4210 Evaluation Kit User manual

RSB
-
4
210
Evaluation Kit
Freescale
i.MX53 Pr
ocessor
-ARM® Cortex™ A8 Architecture

I RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
Part
No.
Edition
1
Printed in Taiwan Mar. 2012
Copyright
The documentation and the software included with this product are copyrighted
2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd.
reserves the right to make improvements in the products described in this
manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of Advantech Co., Ltd. Information provided in this manual is
intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements of the rights of third parties,
which may result from its use.
Acknowledgements
ARM is trademarks of ARM Corporation.
Freescale is trademarks of Freescale Corporation.
Microsoft Windows are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

RSB-4210 Evaluation Kit User Manual II
Packing List
Before setting up the system, check that the items listed below are included and
in good condition. If any item does not accord with the table, please contact your
dealer immediately.
RSB-4210 (P/N: RSB-4210CF-A78AAE)
7" LED PANEL 320N 4WR T/S 800X480(G), 97G070V1N0F-2
(P/N:96LEDK-A070WV32RB1)
LCD Backlight Cable (P/N: 1700019577)
LVDS Cable (P/N: 1700014418)
Touch Cable (P/N: 1700000194)
SQFlash SD Card SLC 2G, 2CH(-40~85°C)(P/N: SQF-ISDS2-2G-ETE)
A CABLE SATA 15P/1*4P-2.5 35cm for AIMB-213 (P/N: 1700018785)
M Cable SATA 7P/SATA 7P 8CM C=R 180/180 (P/N:1700004711)
Mini USB Host Cable (0050/N: 1700019076)
Mini USB Client Cable (P/N: 1700019077)
USB Type-A Cable (P/N: 1700019129)
ADAPTER 100-240V 90W 19V 4.74A W/PFC 9NA0900508
(P/N: 1757002944)
A Cable 2*8P-2.0/SPEAKER*2+DC JACK*3 40CM (P/N: 1700019546)
F Cable IDE#2 10P-2.0/D-SUB 9P(M) 25CM (P/N: 1700100250)
Terminal connector 9P Female (P/N: 1654909900)
DVD-ROM for RSB-4210 Evaluation Kit(2062421010)
RS-232 and RS-485 cable(1700019474)
RS-422 cable(1700019476)
===Power Core (Optional)===
3 pin Power Cord for USA standard (P/N: 1700001524)
3 pin Power Cord for Europe standard (P/N: 170203183C)
3 pin Power Cord for UK standard (P/N: 170203180A)
===Charger Board & Battery (Optional)===
A cable 1*6P-2.5/1*6P-2.5 140mm (P/N: 1700018394)
A cable 2*4P-2.0/2*4P-2.0 90mm (P/N: 1700018395)
PCM-739 Battery charger Board (P/N: 969K073900E)
Battery 11.1V 6300mAh 3S3P (P/N: 1760001300)

III RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or
letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical
shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by
service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work
according to the user’s manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

RSB-4210 Evaluation Kit User Manual IV
Contents
Chapter 1Introduction……………………………1
1.1 Introduction ......................................................................................................................2
1.2 Features ............................................................................................................................3
1.3 Hardware Specification ....................................................................................................4
1.4 Board Block Diagram ........................................................................................................6
Chapter 2H/W Installation………………...………7
2.1 Development it H/W Installation ..................................................................................8
2.1.1 RSB-4210 (Part-A) ..................................................................................................... 10
2.1.2 7” LVDS LCD Modul (Part-B1) ................................................................................. 10
2.1.3 LCD Backlight Cabl (Part-B2) ................................................................................... 10
2.1.4 LVDS Cabl (Part-B3) ................................................................................................ 10
2.1.5 Touch Cabl (Part-B4) ............................................................................................... 10
2.1.6 SQFlash SD Card (Part-C) .......................................................................................... 10
2.1.7 SATA Pow r Cabl (Part-D) ....................................................................................... 10
2.1.8 SATA Cabl (Part-E) .................................................................................................. 11
2.1.9 Mini USB Host Cabl (Part-F) .................................................................................... 11
2.1.10 Mini USB Cli nt Cabl (Part-G) ............................................................................... 11
2.1.11 USB Typ -A Cabl (Part-H) ..................................................................................... 11
2.1.12 Jump r (Part-I) ........................................................................................................ 11
2.1.13 Null mod m cabl (Part-J) ...................................................................................... 11
2.1.14 19V Pow r Adapt r (Part-K) ................................................................................... 11
2.1.15 Pow r Cord (Part-L) ................................................................................................ 11
2.1.16 Sp ak r & Audio Cabl s (Part-M) ........................................................................... 11
2.1.17 Pow r Cabl for Charg r Board (Part-N1) .............................................................. 11
2.1.18 Signal Cabl for Charg r Board (Part-N2) ............................................................... 11
2.1.19 Charg r Board (Part-N3) ......................................................................................... 12
2.1.20 Batt ry (Part-N4) .................................................................................................... 12
2.1.21 K ypad Cabl (Part-O1) .......................................................................................... 12
2.1.22 K ypad (Part-O2) .................................................................................................... 12
2.1.23 Cabl for Susp nd/R s t Button (Part-P) ............................................................... 12
2.1.24 COM Port Cabl (D-SUB 9P to Housing) (Part-Q) ................................................... 12
2.1.25 RS-232 Loopback (Part-R) ....................................................................................... 12

V RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
2.1.26 T rminal Block for CAN/RS-485 (Part-S)................................................................. 12
2.2 RSB-4210 Connectors .................................................................................................... 13
2.2.1 Waf r for 4-wir R sistiv Typ Touch Scr n (CN1) .............................................. 14
2.2.2 Pho nix Conn ctor for CAN Bus (CN2) ..................................................................... 15
2.2.3 Pho nix Conn ctor for COM3, RS-485 (CN3) ........................................................... 16
2.2.4 Syst m Bus (CN4) ..................................................................................................... 17
2.2.5 Pin H ad r for COM5, RS-232 (TX/RX/RTS/CTS) (CN5) ............................................ 19
2.2.6 Pin H ad r for COM4, 3.3V TTL (TX/RX/RTS/CTS) (CN6) .......................................... 20
2.2.7 Pin H ad r for I2S (CN7) ........................................................................................... 21
2.2.8 LVDS0 LCD Conn ctor (CN8) ..................................................................................... 22
2.2.9 Pin H ad r for COM1, RS-232 (TX/RX) (CN9) ........................................................... 23
2.2.10 Pin H ad r for SD2 (CN10) ..................................................................................... 24
2.2.11 Waf r for Backlight Pow r and Controll r (CN11) ................................................. 25
2.2.12 MiniPCI Conn ctor-Latch (CN12) and Conn ctor (CN13) ..................................... 26
2.2.13 LVDS1 LCD Conn ctor (CN14) ................................................................................. 28
2.2.14 Pin H ad r for Jtag (CN15) ..................................................................................... 29
2.2.15 Waf r for SATA pow r (CN16)................................................................................ 30
2.2.16 Waf r for Pow r ON/OFF (CN17) ........................................................................... 31
2.2.17 Eth rn t LAN1&2 Conn ctor (CN18) ...................................................................... 32
2.2.18 Waf r for Coin Batt ry (CN19) ............................................................................... 33
2.2.19 SIM Card slot (CN20) .............................................................................................. 34
2.2.20 Pin H ad r for R s t (RST_BTN1)........................................................................... 35
2.2.21 Pin H ad r for Susp nd (SUS_BTN1) ...................................................................... 36
2.2.22 Pin H ad r for Matrix K ypad (KEYPAD1) .............................................................. 37
2.2.23 Pin H ad r for I2C/SPI (CN21) ................................................................................ 38
2.2.24 Pin H ad r for 20x pins GPIO (GPIO1) ................................................................... 39
2.2.25 SATA Conn ctor (SATA_CN1) ................................................................................. 40
2.2.26 Pin H ad r for USB_HUB1 (USB1) .......................................................................... 41
2.2.27 Waf r for Batt ry Charg r Board – Pow r (BAT_CN1) .......................................... 42
2.2.28 Waf r for Batt ry Charg r Board –Control Signal (BAT_CN2) ............................... 43
2.2.29 USB OTG MINI-AB Conn ctor (USB_OTG1) ............................................................ 44
2.2.30 USB HUB_2&3 (Standard Typ -A) (USB2) .............................................................. 45
2.2.31 VGA Conn ctor (CRT1) ........................................................................................... 46
2.2.32 HDMI Conn ctor (HDMI_CN1) ............................................................................... 47

RSB-4210 Evaluation Kit User Manual VI
2.2.33 Box H ad r for LINE-OUT, LINE-IN, MIC-IN and L&R Sp ak rs (AUDIO1) .............. 48
2.2.34 D-Sub9 Conn ctor for COM2, RS-232 (TX/RX/RTS/ CTS) (COM1) .......................... 49
2.2.35 DC-IN Pow r Jack(DCIN1) ....................................................................................... 50
2.2.36 SD Card Slot (SD1) .................................................................................................. 51
2.3 Mechanical ...................................................................................................................... 52
2.3.1 Conn ctor Location .................................................................................................. 52
2.3.2 RSB-4210 Board Dim nsion ...................................................................................... 53
Chapter 3Software Functionality………………..54
3.1 Package Content ............................................................................................................ 55
3.1.1 Packag for Making Linux Syst m SD Storag Card ................................................. 55
3.1.2 Sourc Cod Packag ............................................................................................... 55
3.1.2.1 Cross Compil r................................................................................................... 56
3.1.2.2 Imag ................................................................................................................. 56
3.1.2.3 Rootfs (Root Fil Syst m) .................................................................................. 56
3.1.2.4 Scripts ................................................................................................................ 57
3.1.2.5 Sourc ................................................................................................................ 57
3.2 Setup Building Environment ......................................................................................... 58
3.2.1 s t nv.sh .................................................................................................................. 59
3.3 Build instructions ........................................................................................................... 59
3.3.1 Build Linux K rn l imag "uImag " .......................................................................... 59
3.3.2 Build Log ................................................................................................................... 60
3.4 Source Code Modification ............................................................................................. 60
3.4.1 Add a Driv r to K rn l by m nuconfig ..................................................................... 60
3.4.2 Chang th Boot Logo .............................................................................................. 61
3.5 Making Linux System Booting Media ........................................................................... 62
3.5.1 Making a Linux Syst m SD Storag Card .................................................................. 62
3.5.1.1 From Linux_Syst m_SD Packag ....................................................................... 62
3.5.1.2 From Sourc Cod Packag ............................................................................... 62
3.5.2 Booting from onboard Flash ..................................................................................... 63
3.5.3 Booting from SATA DOM .......................................................................................... 63
3.6 Debug Message ............................................................................................................. 64
3.7 Linux Software Applications on RSB-4210 .................................................................... 65
3.7.1 Writing your own "H llo World!" application and x cuting it on th RSB-4210 ... 65
3.7.2 Run th Pr -install d Applications on RSB-4210 Platform ....................................... 66
3.7.2.1 Running QT D mos ............................................................................................ 66

VII RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
3.7.2.2 Running Audio D mo......................................................................................... 67
3.7.2.3 Running Vid o D mo ......................................................................................... 67
3.7.2.4 Running Photo D mo ........................................................................................ 68
3.7.2.5 Running Buzz r T sting ..................................................................................... 69
3.7.2.6 Running M mory T sting .................................................................................. 69

Chapter
1
1 Overview
This chapter briefly introduces the
RSB-4210 Product.

RSB-4210 Evaluation Kit User Manual 2
1.1 Introduction
The Evaluation kit for Potential RISC base Design to Order Service (DTOS)
Project. In order to provide Potential DTOS customer efficient / risk less
evaluation tool, Advantech provides many kinds of RISC base evaluation kit.
Before DTOS project kick-off, customer can get the kit to check in detail. The O.S.
ready kit equipped all necessary H/W and S/W tools which customer needs, so it
can shorten user evaluation and speed up user target application development.
The RSB-4210 is designed as a solution board, using Freescale i.MX53 processor
based on ARM® Cortex™ A8 architecture, which is a complete 32-bit, up to
1GHz speed SoC engine. It provides customers a high performance board
subsystem based on ARM® Cortex™ A8 technology with characters of ready-to-
run, compact, and easy-to-expansion in order to meet customers’ versatile needs.
With the flexible I/O interfaces and complete hardware and software solutions, the
RSB-4210 is a fast time-to-market platform for customers to develop their
applications and products easily without considering system integration.
The RSB-4210 Evaluation Kit is a complete system designed for customers to
evaluate the RSB-4210. It integrates all solutions developers need, based on the
RSB-4210 module board, into a package that provides customers an effortless
system platform for project evaluation, application development, and solution
feasibility testing that decreases lead-time and lowers initial expense. The RSB-
4210 Evaluation Kit has already integrated complete certified functions under
Linux’s test kits making project development and implementation becomes an
easy and risk-free way at the starting point.

3 RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
1.2 Features
RSB-4210 is using Freescale i.MX53 Processor - ARM® Cortex™ A8
architecture. The platform feature is heatsink less, compact, reliable & great
power management. So, the platform is good for the following application:
Economical HMI (Human Machine Interface)
Self Service / Access Control
Fleet management / Navigation
Hand-held data collector
And the main features of Freescale i.MX53 Processor are shown as following.
ARM Cortex™-A8 1GHz high performance processor
Supports OpenGL ES 2.0 and OpenVG™ 1.1 hardware accelerators
Supports full HD 1080p video decode and HD 720p video encode
hardware engine
Freescale Smart Speed™ Technology support low power consumption
I/O through 3.3V I/O voltage and wide working temperature by industrial
design concept
Rich I/O for high expansion capability: UART(5), Dual LVDS, Audio,
USB Host, USB OTG, Dual LAN, SD(2), SATA(1), GPIO(20), I
2
C(2),
SPI(1), I
2
S(1), CAN(1), Keypad 6X6, Touch, Mini PCI-E and System Bus.
Supports SATA storage interface and CAN bus for vehicle application
Supports Android, Embedded Linux2.6, Windows Embedded Compact 7
Support wide working temperature -40 ~ 85°C operation temperature
(optional)

RSB-4210 Evaluation Kit User Manual 4
1.3 Hardware Specification
Item Description
Kernel
CPU Freescale i.MX53 1GHz (ARM Cortex A8)
2D/3D Accelerators
Support OpenGL ES 2.0 and OpenVG™ 1.1 hardware accelerators
System RAM 512MB (Optional: 256MB)
Onboard Flash 2GB (Optional: None)
RTC Yes
Watchdog Timer Yes
Reset H/W reset & S/W reset
I/O
COM
-COM 1, RS-232, 2–wire(TX/RX), Pin header, (Debug port)
-COM 2, RS-232, D-Sub9 Connector(TX/RX/RTS/CTS)
-COM 3, RS-485, 2-pin Phoenix Connector
-COM 4, 3.3V TTL, 4–wire(TX/RX/RTS/CTS), Pin header
-COM 5, RS-232, 4–wire(TX/RX/RTS/CTS), Pin header
Ethernet LAN 2 x 10/100 BASE-T (RJ-45)
USB Port
3
x USB 2.0 (High speed)
USB OTG 1 x USB 2.0 OTG (High speed)
SD/MMC 2 x SDIO/MMC interface (SD slot x 1+ pin header x 1)
Mini PCI-E 1 x (Control by USB interface only)
SIM Card slot 1 x
SATA 1 x
Touch Screen 1 x 4 - wire resistive type interface
System Bus Yes (Address: 25 pins, data: 16 pins)
I
2
C Interface 2 x
I
2
S Interface 1 x
SPI Interface 1 x
CAN BUS 1 x
Hotkey/
Matrix keypad Support 6 x 6 matrix keypad
GPIO 20 pins 3.3V TTL level GPIOs
Buzzer control Yes
Multimedia
Graphic Chip CPU internal LCD controller
LCD Resolution Default: 800 x 480 7” WVGA
Optional: 320X 240~ 1920X1080
Dual LVDS 2 x 24-bit LVDS
HDMI 1 x (Co-lay with VGA)
VGA 1 x (Co-lay with HDMI)
Brightness/
Backlight Control Yes
Audio Line-in(Stereo),Line-out(Stereo),Speak-Out(Stereo)&Mic-in(Mono
)

5 RSB-4210 Evaluation Kit User Manual
Chapter1 Overview
Power
DC-input 9~24V ±5%
Battery Support Yes (With external battery and charger board thru connector)
Power Consumption
Normal Run ~2.3W
Full Run ~3.8W
Power Control 1 x Power ON/OFF Pin header 1 x H/W reset Pin header
1 x Suspend Pin header
Power
Management -Standard mode -Idle mode
Mechanical and Environmental
Board size 146 X 102 X 20 mm (PCB thickness 1.6mm; 8 layer)
Weight 110g
Operation
Temperature 0 ~ 60° C (32 ~ 140° F) (-40~ 85°C by component change)
Operating
Humidity 5% ~ 95% Relative Humidity, non condensing
Vibration 3.5G, 1000 times
Others
RoHS Yes
Certification CE/FCC Class A
O.S Embedded Linux2.6(Default), Android 2.2,
and Windows Embedded Compact 7

RSB-4210 Evaluation Kit User Manual 6
1.4 Board Block Diagram
Figure 1-1 Board block diagram

Chapter
2
H/W Installation
This chapter explains the setup
procedures of the RSB-4210
hardware,
including instructions
on setting jumpers
and connecting
peripherals, switches,
indicators and mechanical drawings.
Be sure to read all safety
precautions
before you begin the
installation
procedure.

RSB-4210 Evaluation Kit User Manual 8
2.1 Development it H/W Installation
The Figure 2-1 is RSB-4210 Evaluation Kit Assembly, and the detail
description and Advantech P/N are shown as below table.
Item Description Advantech P/N
Part-A RSB-4210 (P/N: RSB-4210CF-A78AAE)
Part-B1
7” LCD-LED Backlight, LVDS, 800x480, T/S,
97G070V1N0F-2
(P/N: 96LEDK-A070WV32RB1)
Part-B2
LCD Backlight Cable (P/N: 1700019577)
Part-B3
LVDS Cable (P/N: 1700014418)
Part-B4
Touch Cable (P/N: 1700000194)
Part-C SQFlash SD Card, SLC 2GB, (-40~85°C) (P/N: SQF-ISDS2-2G-ETE)
Part-D SATA Power Cable (P/N: 1700018785)
Part-E SATA Cable (P/N: 1700004711)
Part-F Mini USB Host Cable (P/N: 1700019076)
Part-G Mini USB Client Cable (P/N: 1700019077)
Part-H USB Type-A Cable (P/N: 1700019129)
Part-J Null modem cable (P/N: 1700091002 )
Part-K ADAPTER, 100-240V, 19V, 4.74A. (P/N: 1757002944)
Part-L 3Pin Power Cord (USA Standard) [Optional]
3pin Power Cord (Europe standard) [Optional]
3pin Power Cord (UK standard) [Optional]
(P/N: 1700001524)
(P/N: 170203183C)
(P/N: 170203180A)
Part-M Speaker & Audio Cables (P/N: 1700019546)
Part-N1
Power Cable for Charger Board [Optional] (P/N: 1700018394)
Part-N2
Signal Cable for Charger Board [Optional] (P/N: 1700018395)
Part-N3
Charger Board [Optional] (P/N: 969K073900E)
Part-N4
Battery [Optional] (P/N: 1760001300)
Part-O1
8*8 Keypad Cable [Optional] (P/N: 1703200180)
Part-O2
8*8 Keypad [Optional] (P/N: 96969315A0E)
Part-Q COM Port Cable (P/N: 1700100250)
Part-R RS-232 Loopback (P/N: 1654909900)
Part-S Terminal Block for CAN/RS-485 (P/N: 1652002209)

9 RSB-4210 Evaluation Kit User Manual
Chapter2 H/W Installation
Figure 2-1 RSB-4210 Development Kit Assembly

RSB-4210 Evaluation Kit User Manual 10
2.1.1 RSB-4210 (Part-A)
RSB-4210 is a best-cost, low-power, performance SBC (Single Board
Computer) without a heatsink, geared to satisfy the needs for various
industrial computing equipment. Based on Freescale i.MX53 Processor -
ARM® Cortex
TM
A8 architecture, there are DDR3, iNAND flash and other
main ICs. RSB-4210 offers convenient connector layout, easy assembly,
multiple I/O, and includes dual 10/100Mbps Ethernet, three USB
(Universal Serial Bus) 2.0 and five serial ports for easy system
expansibility.
2.1.2 7” LVDS LCD Module (Part-B1)
The 7.0 inch Color TFT-LCD Module with 4-wires resistive type touch
sensor. The module is designed with wide viewing angle; wide operating
temperature and long life LEDs backlight is well suited to be the display
units for Industrial Applications. LED driving board for backlight unit is
included in this panel and the structure of the LED units is replaceable. It’s
built in timing controller and LVDS interface. The display supports the
WVGA (800 (H) x 480(V)) screen format and 16.2M colors (RGB 24bits) or
262K (RGB 18bits) selectable.
2.1.3 LCD Bac light Cable (Part-B2)
The LVDS backlight cable connects RSB-4210 (CN11) and the LCD
backlight connector of 7” LVDS LCD Module.
2.1.4 LVDS Cable (Part-B3)
The LVDS cable connects RSB-4210 LVDS0 connector(CN8) and the LCD
signal connector of 7” LVDS LCD Module.
2.1.5 Touch Cable (Part-B4)
The touch cable connects RSB-4210 (CN1) and the touch connector of 7”
LVDS LCD Module.
2.1.6 SQFlash SD Card (Part-C)
The SQFlash SD card is a standard SD device. It is the flash-based solid-
state drive available and uses SLC NAND flash memory, making it ideal as
an embedded SSD solution. It connects on SD1 of RSB-4210.
2.1.7 SATA Power Cable (Part-D)
The SATA power cable provides the power for SATA HDD. It connects RSB-
4210 (CN16) and the SATA HDD.

11 RSB-4210 Evaluation Kit User Manual
Chapter2 H/W Installation
2.1.8 SATA Cable (Part-E)
The SATA cable provides the control signal for SATA HDD. It connects
RSB-4210 (SATA_CN1) and the SATA HDD.
2.1.9 Mini USB Host Cable (Part-F)
The mini USB Host cable connects RSB-4210 (USB_OTG1) and one USB
client device. For example, USB mouse/keyboard.
2.1.10 Mini USB Client Cable (Part-G)
The mini USB Client cable connects RSB-4210 (USB_OTG1) and one
PC/NB.
2.1.11 USB Type-A Cable (Part-H)
The USB extend cable provide Type-A for USB device. For example, USB
mouse/keyboard.
2.1.12 Jumper (Part-I)
When you plug-in the adapter and the wafer(CN17) is shorted by this
jumper, the system will power-on.
2.1.13 Null modem cable (Part-J)
The null modem cable connects RSB-4210 COM ports and a serial device.
2.1.14 19V Power Adapter (Part-K)
This is an AC to DC power device, it can provide for a 19V DC output (60W
max) with constant voltage sources (100V~240V).
2.1.15 Power Cord (Part-L)
3P Power Cord (USA, Europe or UK standard) for 19V Power Adapter AC
input.
2.1.16 Spea er & Audio Cables (Part-M)
The cable connects RSB-4210 (AUDIO1) and LINE-OUT, LINE-IN, MIC-IN
and L&R Speakers.
2.1.17 Power Cable for Charger Board (Part-N1)
This cable provides the power for charger board. It connects RSB-4210
(BAT_CN1) and the charger board (CN2).
2.1.18 Signal Cable for Charger Board (Part-N2)
This cable provides the control signal for charger board. It connects RSB-
4210 (BAT_CN2) and the charger board (CN1).