Advantech ASMB-787 User manual

The information contained in this document has been carefully researched and is, to the best of our
knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or
consequential, resulting from the use of the information provided herein. Our products are not intended for
use in systems in which failures of product could result in personal injury. All trademarks mentioned herein
are property of their respective owners. All specifications are subject to change without notice.
Manual
ADVANTECH
ASMB-787
Industrial ATX Server Motherboard for 10th Gen. Core™& Xeon® Processors
with Intel® W480E Chipset

ASMB-787 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 Startup manual
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 1 COM cable (for connection to real panel)
• 1 I/O port bracket
• 1 Warranty card
• 1 JFP1 cable
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
le.AcrobatReadercanbedownloadedat:
http://www.adobe.com/downloads/ (Acrobat is a
trademark of Adobe)
ASMB-787 LGA 1200 Intel®Xeon®W & 10th Gen. Core™
ATX Server Board with 4 x DDR4, 5 x PCIe, 2 x PCI,
6 x USB 3.2, 5 x SATA 3, Quad/Dual LANs, and IPMI
Startup Manual
Standard Functions
• CPU: LGA 1200 Intel®Xeon®W and 10th Gen. Core™ i9/
i7/i5/i3 processor
• BIOS: AMI 256 Mb SPI BIOS
• Chipset: Intel W480E
• System memory: Dual Channel DDR4 ECC/Non-ECC
2933/2666/2400MHzunbu󰀨eredDIMM,Max.128GB
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 128 GB RAM
when 128 GB RAM is installed.
• SATA3 interface: 5xSATA36Gb/sportstosupportIntel
Rapid Storage Technology with software RAID 0, 1, 10 &
5 (for Windows only)
• Serial ports: Two serial ports onboard, only support RS-
232 (one can be in rear IO via COM cable connection)
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse via KMBS1 pin header
• Watchdog timer: 255 level timer intervals (sec/min)
• USB 3.2: SupportsuptosixUSB3.2ports,fourGen2
ports in rear I/O and two Gen1 ports from on-board pin
header
• USB 2.0: SupportsuptosevenUSB2.0ports(1*Type-A)
Display Interface
• Chipset: CPUintegratedIntelHDgraphicscontroller
• Display memory: 1GBmaximumsharedmemorywith
2 GB and above system memory installed (BIOS default
is 256 MB)
• Resolution:
-SupportsVGAupto1920x1200resolution@60Hz
refresh rate
-SupportsDVIupto1920x1200resolution@60Hz
refresh rate
-SupportsHDMI2.0upto2K/4Kresolution@60Hz
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1: Intel
®
I219LM; LAN2 ~ LAN4: Intel
®
I210AT
(LAN2isBMCsharedNIC;LAN3/4isforG4SKUonly)
Mechanical and Environmental
• Dimensions (L x W): 244x304mm(9.6”x12”)
• Power supply voltage: +3.3 V, +5 V, ±12 V, 5 Vsb
• Power consumption: Max.load:+3.3V@1.69A,+5V@
1.68A,+12V@0.31A,+12V(8P)@9.25A,+5Vsb@
0.01 A
• Operating temperature: 0~60°C(dependsonCPUspeed
and cooler solution)
• Weight: 0.5 kg (weight of board)
For more information on this and other Advantech prod-
ucts, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our sup-
port website for ASMB-787 at:
https://advt.ch/asmb787
Register your products on our website and get 2 months
extrawarrantyforFREEat:
http://www.register.advantech.com
This manual is for the ASMB-787 series Rev. A1.
Part No. 2041B78700
Printed in China
1st Edition
October 2020
Packing List Specications

2 ASMB-787 Startup Manual
Connector list
PCI_SLOT1,
PCI_SLOT2 PCI slot
PCIEX1_SLOT5 PCIex1slot(Gen3x1link)
PCIEX4_SLOT3,
PCIEX4_SLOT7 PCIex4slot(Gen3x4link)
PCIEX8_SLOT4,
PCIEX16_SLOT6
PCIEx8&x16slots(oneGen3
x16linkforslot6ortwoGen3
x8linkforslot4and6)
PMBUS1 PMBUSconnectortocommuni-
cate with power supply
SATA0~4 SATA III (6 Gb/s)
SMBUS1 SMBus from PCH
SYS_LED1 System information LED con-
nector
SYSFAN0, SYSFAN1,
SYSFAN2, SYSFAN3 System FAN connector
SPI_CN1 SPIashcardpinheader
SPDIF_OUT1 SPDIF audio output pin header
USB5_6 USB3.2Gen1port(Header)
USB7_8,USB9_10,
USB11_12 USB2.0port(Header)
USB13 USB2.0port(USBTypeA)
Jumper list
Label Function
HDMI_I2C1 For RD debugging
JCMOS1 CMOS clear
JME1 Intel ME Disable jumper for ME/
BIOS update
JWDT1 Watchdog reset
JUSB_1
RearwindowUSB3.2Gen2
port power source switch
between +5 VSB and +5 V
JUSB_2
OnboardUSB2.0/3.2Gen1port
power source switch between
+5 VSB and +5 V
JCASE1 Case open
JPEG1, JPEG2 x16orx8x8orx8x4x4forslot-6
JPEG3 Default (1-2)/reserve for RD
debug (2-3)
JPRSNT1
PCIe card present pin support
for PCIEX8_SLOT4
Auto detect (1-2)/Manual detect
(2-3)
The board has a number of jumpers that allow you to con-
gureyoursystemtosuityourapplication.Thetablebelow
lists the function of each jumper and connector.
Connector list
Label Function
ATXPWR1 ATX 24-pin main power connec-
tor (for System)
ATX12V1 8-pin power connector
(forCPU)
AUDIO1~2 Audio connector
BAT1 For RTC battery
BAT2 For optional battery kit
BIOS_SKT1 BIOS SPI ROM
BMC_DEBUG1 For RD debugging
BMC_UART1 BMC debug message
BMC_VGA1 BMC VGA connector
BMC_SPI1 BMC image ROM
COM1, COM2 Serial port: RS-232
CPUFAN0 CPUFANconnector
DIMMA0, DIMMA1,
DIMMB0, DIMMB1 DDR4 288-pin slot
DVI1 DVI connector
EX_THR1 Forexternalthermistorcablekit
FPAUD1 Front panel audio header
GPIO1 8-bit GPIO header
HDMI1_VGA1 HDMI + VGA connector
JFP1
Power Switch/ Power Reset/
LANLED1/LANLED2/
HDD LED/Power LED
Power LED Behavior:
• Suspend:Fastash(ATX/AT)
• System On: ON (ATX/AT)
• SystemO󰀨:OFF(ATX/AT)
KBMS1 Externalkeyboardandmouse
connector (6 pin)
LAN1_USB1_2,
LAN2_USB3_4
LAN1/USB3.2Gen2port1,2
stack connector
LAN2/USB3.2Gen2port3,4
stack connector
LAN3_LAN4 LAN3 & LAN4 connector
LPC1, LPC2
Low pin count connector
for Advantech TPM and
RS232/422/485 module
LPT1 Parallel port
M2_2280_1 M.2 2280/2242 (PCIe/SATA)
Jumpers and Connectors Jumpers and Connectors (Cont.)

ASMB-787 Startup Manual 3
Jumper list
JPSMB1, JPSMB2 PCIESLOTSMBUSconnector:
to PCH (1-2)/to BMC (2-3)
JP_PCICLK1 PCI slot 66MHz clock:
Enable (1-2)/Disable (2-3)
JSMB1 For RD debugging
JTHR_SEL1 Toselectonboardorexternal
thermistor
PSON1 AT (1-2)/ATX (2-3)
PCIEX16_Slot6Conguration(JPEG1,JPEG2)
Function JPEG1 JPEG2
Slot6 PCIe
x16(Default)
1-2 closed 1-2 closed
Slot6 PCIe
x8+x8
2-3 closed 1-2 closed
Slot6 PCIe
x8+x4+x4
1 2 3
2-3 closed
1 2 3
2-3 closed
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 KeepCMOSdata/DisableMEupdate*
2-3 Clear CMOS data/Enable ME update
*:Default
Keep CMOS data/ Clear CMOS data/
Disable ME update Enable ME update
JWDT1: Watchdog timer output option
Closed Pins
Result
1-2 Systemreset*
2-3 NC
*:Default
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
System Reset 1-2 Closed NC 2-3 Closed
1 2 3
1 2 3
PSON1:ATX,ATmodeselector
Closed Pins
Result
1-2 AT Mode
2-3 ATXMode*
*:Default
AT Mode 1-2 closed ATX Mode 2-3 closed
1 2 3
1 2 3
1PWD BTN
2.0 mm JFP connector on board
Description Pin Number Description
RST BTN
2
PWD GND
43PWD GND
LAN1_LED+
5
6
LAN2_LED+
LAN1_LED -
8
7
LAN2_LED -
CRPS_Detect
10 9SYS_LED+
GND
12 11 SYS_LED-
PWR_LED+
14
13
HDD_LED+
PWR_LED -
16
15
HDD_LED-
▼
2.0 mm JFP connector to 2.54 mm Pitch Header
Description
Pin Number
Description
(Red) PWD BTN
▼12RST BTN (White)
(Black) PWD GND
3
4
PWD GND (Black)
(Blue) LAN1_LED+
56LAN2_LED+ (Brown)
(Red) LAN1_LED -
78LAN2_LED - (Black)
Key
(Orang) HDD_LED+
13
14
PWR LED+ (Red)
(Black) HDD_LED -
15
Key 16 PWR LED - (Black)
SATA storage mapping table
Connector Label BIOS Menu Intel Rapid Storage
Technology
SATA0 SATA0 Internal empty port 3
SATA1 SATA1 Internal empty port 4
SATA2 SATA2 Internal empty port 5
SATA3 SATA3 Internal empty port 6
SATA4 SATA4 Internal empty port 7
Jumpers and Connectors (Cont.) Installation Note

4 ASMB-787 Startup Manual
Caution! The computer is supplied with a battery-powered realtimeclockcircuit.Thereisadangerofexplosionifbatteryis
incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used
batteries according to manufacturer’s instructions.
This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Board Layout: Jumper and Connector Locations
HDMI1_VGA1
LAN3_LAN4
DVI1
LAN2_USB3_4
COM2
Intel LGA1200 Socket
USB7~12
KBMS1
Intel W480E PCH
PMBUS1
ASPEED 2600 BMC
DIMM A0
LAN1_USB1_2
AUDIO1~2
PCI_SLOT1~2
PCIEX16_SLOT6
PCIEX4_SLOT7
ATXPWR1
DIMM A1
DIMM B0
DIMM B1
ATX12V1
FDAUD1
COM1_
JPEG1~3
SYS_LED1
JFP1
LPC1_2
SATA0~5
SPI_CN1
BIOS_SKT1
SPDIF_OUT1
SYSFAN3
CPUFAN0
BAT1
M2_2280_1
JPSMB1~2
JWDT1
JME1
USB5_6
JCMOS1
SYSFAN0
GPIO1
PSON1
SMBUS1
JCASE1
EX_THR1
SYSFAN1~2 JTHR_SEL1
USB13
JUSB_1~2
BMC_DEBUG1
BMC_SPI1
BMC_UART1
LPT1
PCIEX1_SLOT5
PCIEX8_SLOT4
PCIEX4_SLOT3
BAT2
JP_PCICLK1
BMC_VGA1
JPRSNT1 JSMB1
HDMI_I2C1
Declaration of Conformity
Board Layout

Our company network supports you worldwide with offices in Germany, Austria, Switzerland, the UK and the
USA. For more information please contact:
Headquarters
Germany
FORTEC Elektronik AG
Augsburger Str. 2b
82110 Germering
Phone: [phone]
E-Mail: [email protected]
Internet: www.fortecag.de
Fortec Group Members
Austria
Distec GmbH Office Vienna
Nuschinggasse 12
1230 Wien
Phone: [phone]
E-Mail: [email protected]
Internet: www.distec.de
Germany
Distec GmbH
Augsburger Str. 2b
82110 Germering
Phone: [phone]
E-Mail: [email protected]
Internet: www.distec.de
Switzerland
ALTRAC AG
Bahnhofstraße 3
5436 Würenlos
Phone: [phone]
E-Mail: [email protected]
Internet: www.altrac.ch
United Kingdom
Display Technology Ltd.
Osprey House, 1 Osprey Court
Hichingbrooke Business Park
Huntingdon, Cambridgeshire, PE29 6FN
Phone: [phone]
E-Mail: [email protected]
Internet: www. displaytechnology.co.uk
USA
Apollo Display Technologies, Corp.
87 Raynor Avenue,
Unit 1Ronkonkoma,
NY 11779
Phone: [phone]
E-Mail: [email protected]
Internet: www.apollodisplays.com