Advantech MIO-2261 Installation and operation manual

MIO-2261 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. 1 MIO-2261 SBC
2. 1 Startup Manual
3. 1 Utility CD (including user manual and drivers)
4. 1 SATA cable p/n: 1700006291
5. 1 Audio cable p/n: 1700019156
6. 1 COM cable p/n: 1701200220
7. 1 SATA Power cable p/n: 1700019656
8. 1 USB cable p/n: 1700002172
9. 1 AT power cable p/n: 1700019705
10. 1 Heatsink p/n: 1960055792T001
11. Screw and stud pack (1 screw
for Mini PCIe, 4 M3 studs and
screws for heatsink) p/n: 9666226000E
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of MIO-2261, please refer
to information on the enclosed CD-ROM (in PDF
format).
Note 2: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
http://get.adobe.com/reader/ (Acrobat is a trade-
mark of Adobe)
MIO-2261 Intel®AtomTM N2600/ N2800 Pico-ITX SBC,
DDR3, 18/24-bit LVDS, VGA, 1 GbE, Half-size Mini
PCIe, 4 USB, 2 COM, SMBus, I2C, mSATA & MIOe
Startup Manual
General
• CPU: Intel®Atom™ Dual Core 1.6 GHz (N2600) /
1.86 GHz (N2800)
• System Chipset: Intel® Atom™ N2600/ N2800 + NM10
• System Memory: 1 x 204-pin SODIMM socket DDR3 800
MHz (N2600) /1066 MHz (N2800), up to 4 GB
• L2 Catch: 1 MB on die
• BIOS: AMI EFI 16 Mbit Flash ROM
• Watchdog Timer: 255 level interval timer
• Battery: Lithium 3 V/210 mAH
Note: How to clear CMOS (Must follow steps below):
1. Turn off system power.
2. Unplug CR2032 battery cable on BH1.
3. Waiting for 15sec or short BH1 pin1-2.
4. Connect battery cable on BH1.
5. Turn on system power.
• Serial ATA: One SATA II interface, up to 300 MB/s
• USB: Four USB 2.0 compliant ports
• Audio: High definition audio (HD), line-in, line-out
• GPIO: 8-bit general purpose input/output
• Expansion Interface: Half size Mini PCIe, MIOe
MIOe Expansion Slot
• Interface: 2 x USB 2.0, 2 x PCIe x1, LPC, HD Audio
line-out, SMBus, DP or HDMI supported by request, 5
Vsb/12 Vsb
• Total peripheral power supply output: 5 V @ 3 A for
CPU board and MI/O Extension module totally, 12 V @ 2
A for MI/O Extension module
VGA/LVDS Interface
• Controller: Intel®N2600 / N2800, DirectX 9 and
OpenGL3.0 support
• Output Interfaces:
- VGA: Up to 1920 x 1200 (WUXGA)
- LVDS: Single channel 18/24-bit LVDS,
up to 1366 x 768 (WXGA)
- Dual Display: CRT + LVDS
Ethernet Interface
• Support single 10/100/1000 Mbps Ethernet interface
• Controller: Intel® 82583V (GbE1)
Specications Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://service.advantech.com.tw/support/
This manual is for the MIO-2261 Series Rev. A1
Part No. 2006226100
Printed in China
1st Edition
June 2012

2 MIO-2261 Startup Manual
Jumper Settings
J1
LCD Power / Auto Power On
Part Number 1653003260
Footprint
HD_3x2P_79
Description PIN HEADER 3*2P 180D(M) 2.0 mm
SMD 21N22050
Setting
Function
(1-2) +5 V
(3-4)* +3.3 V
(5-6)* Auto Power On
* default
Mechanical and Environmental
• Dimensions: 100 x 72 mm (3.9” x 2.8”)
Mechanical Drawings are on page 4 - 6.
• Power Requirement: Single 12 V DC power input
• Power Consumption (with 1 GB memory):
- Typical in XP mode:
N2600: 0.35 A @ 12 V (4.2 W)
N2800: 0.46 A@ 12 V (5.52 W)
- Max in HCT:
N2600: 0.76 A @ 12 V (9.12 W)
N2800: 0.80 A @ 12 V (9.6 W)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Weight: 0.42 kg (0.93 lb) (reference total weight)
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Jumpers
Label Function
J1
LCD Power / Auto Power on
Connectors
Label Function
CN1 12V Power Input
CN2 DC JACK (support by request)
CN3 DDR3 SO-DIMM
CN4 GPIO
CN5 VGA
CN6 mSATA
CN7 S ATA
CN8 Mini PCIe
CN9 External USB
CN10 Internal USB
CN11 COM1/ COM2
CN12 SMBus (or I2C, support by request)
CN13 Front Panel
CN14 Gigabit Ethernet
CN15 HD Audio
CN16 MIOe
CN17 Inverter Power Output
CN18 24 bits LVDS Panel
BH1 Battery
Jumpers and Connectors
Jumpers and Connectors
Caution! The computer is provided with a battery-powered
real-time clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
Specications Cont.

MIO-2261 Startup Manual 3
MIO-2261 Connector Locations
Figure 1: MIO-2261 Connect Location (Top Side)
Figure 2: MIO-2261 Connect Location (Bottom Side)
CN18
CN15
CN11
CN8CN4CN10CN12CN17
J1
CN6
CN5 CN9 CN14
CN1
BH1
CN5
CNCN
CN18
CN13CN
CN13
CN3
CN7
CN16

4 MIO-2261 Startup Manual
Figure 3: MIO-2261 Mechanical Drawing (Top Side)
Figure 4: MIO-2261 Mechanical Drawing (Bottom Side)
MIO-2261 Mechanical Drawing
Unit: mm
Unit: mm

MIO-2261 Startup Manual 5
Figure 5: MIO-2261 Mechanical Drawing (Side View)
Figure 6: MIO-2261 Mechanical Drawing (Side View with Optional DC/Jack)
MIO-2261 Mechanical Drawing
Unit: mm
Unit: mm

6 MIO-2261 Startup Manual
Figure 7: MIO-2261 Mechanical Drawing (Side vew with Heatsink)
Figure 8: MIO-2261 Mechanical Drawing (Side View wih Optional Heatspreader)
MIO-2261 Mechanical Drawing
Unit: mm
Unit: mm