Advantech PPC-MB-620 Installation and operation manual

PPC-MB-620 Startup Manual 1
Before installation, check to ensure that the following items
are included in the shipment:
1. 1 x PPC-MB-620 mini-ITX motherboard
2. 1 x COM cable (1-to-4 DB9)
3. 1 x SATA cable
4. 1 x PPC-MB-620 startup manual
5. 1 x Warranty card
6. 1 x Thermal grease
7. 14 x COM port screws
8. 2 x M.2 packet screws
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note 1:  FordetailedPPC-MB-620specications,refer
to the latest product information provided on the
Advantech website (PPC-600 model).
Note 2:  AcrobatReaderisrequiredtoviewPDFles.
This software can be downloaded from www.
adobe.com/Products/acrobat/readstep2.html
(Acrobat is a trademark of Adobe).
PPC-MB-620 Mini-ITX Motherboard with Intel® Core™ i9/
i7/i5/i3/Celeron® Processor, DP/HDMI, 5 x COM, 6 x USB,
3 x LAN, PCIe x16, and M.2 (M Key, B key and E Key)
Startup Manual
1. Insert the memory module into the memory slot at a 45
degree angle, as shown below. Ensure that the gold
ngersofthemodulearefullyinsertedintotheslot.
2. Once inserted, gently press the memory module into
the slot until the tabs snap into place, securing the
module in position.
45°
Installation Guide
Packing List
For more information about this or other Advantech
products, visit our website at
http://www.advantech.com
For technical support and service, visit our support
website at
http://support.advantech.com
This manual is for PPC-MB-620, Rev. A1.
Part No. 2044062000
Printed in China
Edition 1
March 2023

2 PPC-MB-620 Startup Manual
System
CPU
i9-12900E/
i9-12900TE
i7-12700E/
i7-12700TE
i5-12500E/
i5-12500TE
i3-12100E/
i3-12100TE
G7400E/
G7400TE
G6900E/
G6900TE
Core
Number 16/16 12/12 6/6 4/4 2/2 2/2
Max Speed
2.3GHz (Up to
5.0GHz)/
1.1GHz (Up to
4.8GHz)
2.1GHz (Up to
4.8GHz)/
1.4GHz (Up to
4.6GHz)
2.9GHz (Up to
4.5GHz)/
1.9GHz (Up to
4.3GHz)
3.2GHz (Up to
4.2GHz)/
2.1GHz (Up to
4.0GHz)
3.6GHz/
3.0GHz
3.0GHz/
2.4GHz
SmartCache 30/30MB 25/25MB 18/18MB 12/12MB 6/6MB 4/4MB
TDP 65W/35W 65W/35W 65W/35W 60W/35W 46W/35W 46W/35W
Memory 2 x 262-pin SODIMM DDR5, 4800 MHz , up to 32 GB (non-ECC )
Chipset Q670E H610E
Ethernet
Controller
LAN1: 1Gb Intel i219LM (support AMT 16.0
only for i7 & i5);
LAN2: 2.5Gb Intel i226-LM
LAN1: 1Gb Intel i219LM (support AMT 16.0 only for i7
& i5);
LAN2: 2.5Gb Intel i226-LM
LAN3: 2.5Gb Intel i226-LM
Connector RJ45 x2 RJ45 x3
Rear I/O
USB 6 (USB 3.2 Gen 2) 6 (2 x USB 3.2 Gen 2, 2 x USB 3.2 Gen 1, 2 x USB 2.0)
Ethernet 2 3
Display Port 1
HDMI 1
Audio 2 (Mic-in, Line-out)
Serial 2 (1 x RS-232/422/485, 1 x RS-232)
Internal
Connector
USB 3 x USB 2.0 1 x USB 2.0
SATA 2 x SATA 3.0 ( support RAID 0,1) 2 x SATA 3.0
Serial 3 x RS-232
TPM 1
GPIO 8-bit
Expansion
M.2
1 x slot (2280 M key) for storage (SATA & PCIe*4);
1 x slot (2230 E key) for wireless (PCIE & USB2.0)
1 x slot ( 3042 & 3052 B key) supports PCIE &
USB3.1 & USB2.0 1 x slot (3042 & 3052 B key) supports PCIE & USB2.0
PCIe x16
(Gen5) 1 x slot
Watchdog Timer 255timerintervals,congurableusingsoftware
Dimensions (W x H) 170 mm x 170 mm (6.69" x 6.69")
OS support Microsoft® Win 10 IOT LTSC(64-bit)/Win 11, Linux
Specications

PPC-MB-620 Startup Manual 3
Board Layout: Jumper and Connector Locations

4 PPC-MB-620 Startup Manual
COM12: COM 2 Connector
Pin Denition
(RS-232)
Denition
(RS-422)
Denition
(RS-485)
1DCD TX- TX RX-
2RXD TX+ TX RX+
3TXD RX+
4DTR RX-
5 GND GND GND
6 DSR
7RTS
8 CTS
9 RI
CN6: COM 3/4/5 and GPIO Connector
1 COM3_DCD# 2 COM3_DSR#
3 COM3_RXD 4 COM3_RTS#
5 COM3_TXD 6 COM3_CTS#
7 COM3_DTR# 8 COM3_RI#
9 GND 10 GND
11 COM4_DCD# 12 COM4_DSR#
13 COM4_RXD 14 COM4_RTS#
15 COM4_TXD 16 COM4_CTS#
17 COM4_DTR# 18 COM4_RI#
19 GND 20 GND
21 COM5_DCD# 22 COM5_DSR#
23 COM5_RXD 24 COM5_RTS#
25 COM5_TXD 26 COM5_CTS#
27 COM5_DTR# 28 COM5_RI#
29 GND 30 GND
31 GND 32 SIO_GPIO6
33 SIO_GPIO4 34 SIO_GPIO2
35 SIO_GPIO0 36 SIO_GPIO7
37 SIO_GPIO5 38 SIO_GPIO3
39 SIO_GPIO1 40 +V5_DUAL
The PPC-MB-620 motherboard features a number of
jumpersthatallowuserstocongurethesystemaccording
tospecicapplications.Thefunctionsofeachjumperand
connector are listed in the table below.
Connector and Headers
Connectors and Headers List
Label Function
CN12 Mic-In/Line-Out connector
LAN+USBx2
(left) RJ45(i219) + USB 3.2 stack connector
LAN+USBx2
(right) RJ45(i226) + USB 3.2 stack connector
HDMI+DP HDMI+DisplayPort connector
COM1(UP)/
COM2(Down) COM 1/2 connector
USBx2(LAN) USB 3.2/RJ45(i226) stack connector
CN15 Power button connector
CN14 Power LED connector
CN13 Audioamplieroutputconnector
CN10 COM 3/4/5 and GPIO connector
CN16 ATX power supply connector
ATX12V1 ATX 12V power supply connector
PCIEX16 PCIe x16 slot connector
CN11 Touchscreen connector
SATA1/SATA2 SATA signal connector
CPU FAN CPU fan power connector
SYS FAN1/
SYS FAN2 System fan power connector
CN17/CN25 2 x USB 2.0 pin header
CN8 USB 2.0 pin header
DIMMA/
DIMMB DDR5 SODIMM socket
CN2 LVDS backlight inverter power con-
nector
CN1 LVDS panel connector
M.2 E Key
2230 M.2 E key
M.2 B Key
3052 M.2 B key
SIMI SIMI Card Connetor
M.2 M Key
2280(NVME) M.2 M key
BAT1 Battery connector
Jumpers and Connectors Jumpers and Connectors (Cont.)

PPC-MB-620 Startup Manual 5
CN16: Touch Connector
Pin Denition
1 Y+
2 X+
3 SENSE
4Y-
5 X-
Sysfan 1 ~ 2: System Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CPUFAN1: CPU Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CN4: Power LED Connector
Pin Denition
1 +V5_DUAL
2 +V5
3 GND
4 GND
AMP1: Audio Amplier Output Connector
Pin Denition
1 SPK L-
2 SPK L+
3 SPK R+
4 SPK R-
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)
Jumper Settings
Jumper List
Jumper Function
JP1 LCD power select
JP2 Enable power select
JP3 LVDS resolution select
JP4 LVDS PWM power select
JP5 COM pin 9 power select (COM 1 and 2)
JP6 Touch power select
PSON1 ATX/AT select
JCMOS1 RTC select
ATX/AT Select (JP1)
(1-2) P1 AT
(2-3) P2 ATX (default)
1
2
3
1
2
3
P1 P2
RTC Select (Jcmos1)
(1-2) P3 Normal (default)
(2-3) P4 Clear CMOS
1
2
3
1
2
3
P3 P4

6 PPC-MB-620 Startup Manual
Jumpers and Connectors (Cont.)
DI/O Pin Denition (DB9)
Pin Denition
1 GND
2 GPIO4
3 GPIO0
4 GPIO5
5 GPIO1
6 GPIO6
7 GPIO2
8 GPIO7
9 GPIO3
Touch Power Select (JP2)
(1-2) P5 Connect resistive touchscreen (default)
NC P6 Disconnect resistive touchscreen
1
2
1
2
P5 P6
LCD Power Select (JP3)
(1-2) P7 +V5
(2-3) P8 +V3.3 (default)
1
2
3
1
2
3
P7 P8
Enable Power Select (JP4)
(1-2) P9 +V5
(2-3) P10 +V3.3 (default)
P9 P10
1
2
3
1
2
3
LVDS PWM Power Select (JP5)
(1-2) P11 +V5
(2-3) P12 +V3.3 (default)
P11 P12
COM Ring Select (JP6)
(1-3)/(2-4)
P13/P14 COM 2/1 ring (default)
(3-5)/(4-6)
P15/P16 COM 2/1 5V
(7-9)/(8-10)
P17/P18 COM 2/1 12V
P13 P14
P15 P16
P17 P18
1
2
3
1
2
3
Jumpers and Connectors (Cont.)
3
64
5
2 8
9
7
10
13
64
5
2 8
9
7
10
1
3
64
5
2 8
9
7
10
13
64
5
2 8
9
7
10
1
3
64
5
2 8
9
7
10
1
3
64
5
2 8
9
7
10
1