Advantech UNO-P166 Installation and operation manual

1 Startup Manual
STARTUP MANUAL
UNO-P166
6-port Isolated RS-232/422/485, 2-port IRIG-B, PCI-104 Card for UNO-4672
Before installation, please make sure that you have:
• UNO-P166 plug in card
• Nameplate for integration
• Front and Rear brackets
• 11 x hex metal posts
• Driver CD
If anything is missing or damaged, contact your
distributor or sales representative immediately
UNO-P166 can add 6 more isolated serial ports and
2 IRIG-B ports for UNO-4672, it supports the fol-
lowing specifications:
• 6-port RS-232/422/485
• Automatic RS-485 data flow control
• 2,500 VDC EFT Protection
• 2,500 VDC Isolation Protection
• IRQ: All use the same IRQ assigned by PCI Bus
• Data bits: 5, 6, 7, 8
• Stop bits: 1, 1.5, 2
• Parity: None, Even, Odd
• Baud-rate (bps): RS-232 : 50~115.2 k
RS-422/485 : 50~921.6 k
• Transmission Distance: 1000 m (RS-422/485)
• Data Signals:
TxD, RxD, RTS, CTS, GND for RS-232
Data+, Data-, GND for RS-485
Tx+, Tx-, Rx+, Rx- for RS-422
IRIG Time Code Input
• Connectors: Female BNC-connector, male 9-pole
D-Sub connector
• Supported Formats: IRIG-B00X according to
IRIG STANDARD 200-04, 200-98
• Input Signal: Unmodulated (DC level shift) IRIG-
B, input insulated by photocoupler
IRIG Time Code Decoding
• Message syntax: QQQHHMMSS (year, day, hour,
minute & second)
• Resolution time: 1s
• Status info: 1 status LEDs for indicators
Follow these steps to integrate into UNO-4672:
1. Please refer to the Chapter 3 of UNO-4672’s
user manual to remove the L-shaped cover.
2. Remove each pair of hex nuts of the 8xCOM port
3. Refer to the ‘COM port Configuration’ section on
next page to set the configuration.
4. Refer to the screw hole of UNO-P166 to unscrew
the related screws on UNO-4672 and build the
provided 11x hex metal post on the same posi-
tion.
5. Plug UNO-P166 into UNO-4672 and fix it by the
screws you just get down on step 4.
6. Refer to the above diagram, replace the front/rear
bracket and nameplate to fit the UNO-P166’s I/O
and LEDs
7. Put the L-shape cover back and fix it, then screw
back the hex nuts you get down on step 2
8. As for the software driver, please refer to the
companion driver CD.
Packing List IRIG-B Information
Overview
Notes
For more information on this and other Advantech
products, please visit our websites at:
http://www.advantech.com/eAutomation
For technical support and service:
http://www.advantech.com/support/
This startup manual is for UNO-P166
Part No. 2003016600 1st Edition
April 2011
Diagram
Installation

2 Startup Manual
Please follow the below description to set the COM
ports and IRIG-B interface, please also refer to the
UNO-4672’s user manual and software manual in the
IRIG-B driver for detailed function description:
1. Selection of RS-232 or RS-422/485
RS-232 Jumper Setting (Default)
RS-422/485 Jumper Setting
2. Switch the RS-485 auto-flow control or RS-422 Mas-
ter/Slave mode (SW1)
3. Setting the Terminal Resistor
4. Setting the RS-422 for Multi-master application
5. Selection of IRIG-B TTL Output
COM Port Configuration
COM port Jumper
COM11 JP1
COM12 JP3
COM13 JP5
COM14 JP7
COM15 JP9
COM16 JP11
COM port DIP of SW1
COM11 DIP1
COM12 DIP2
COM13 DIP3
COM14 DIP4
COM15 DIP5
COM16 DIP6
SW1 Status Description
ON RS-422: Master mode
RS-485: N/A
OFF(Default) RS-422: Slave mode
RS-485: Auto flow control
FGH IEDCBA J
FGH IEDCBA J
COM port Jumper
COM11 JP2
COM12 JP4
COM13 JP6
COM14 JP8
COM15 JP10
COM16 JP12
IRIG RS-485 JP13
Short Description
1-3 Add 120 Ohm termial resistor on Tx+/Tx- of
RS-422 or Data+/Data- of RS-485
3-5 Add 300 Ohm termial resistor on Tx+/Tx- of
RS-422 or Data+/Data- of RS-485
2-4 Add 120 Ohm termial resistor on Rx+/Rx- of
RS-422
4-6 Add 300 Ohm termial resistor on Rx+/Rx- of
RS-422
COM port Switches Status
COM11 SW2 ON: Normal (default)
OFF: RS-422 multi-master
COM12 SW3
COM13 SW4
COM14 SW5
COM15 SW6
COM16 SW7
Short Description
1-2 Output from Input
2-3 Output through Buffer
1
3
5
2
4
6