Advantech ASMB-816 Series Installation and operation manual

ASMB-816 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x ASMB-816 Startup Manual
• 2 x SATA data cables
• 2 x SATA power cables
• 2 x CPU power cables (8P)
• 1 x CPU carrier
• 1 x Front panel convert cable
• 1 x I/O port bracket
• 1 x M.2 screw
If any of these items are missing or damaged, please
contact your distributor or sales representative immediately.
Note 1:  AcrobatReaderisrequiredtoviewanyPDFle.
Acrobat Reader can be downloaded at:
https://www.adobe.com/downloads.html
(Acrobat is a trademark of Adobe)
ASMB-816 Series LGA 4189 Intel 3rd Generation Xeon®
Scalable ATX Server Board with 8 DDR4, 3 PCIe x16, 8
SATA3, 6 USB3.0, Dual 10GbE, IPMI
Startup Manual
Standard M/B Functions
• CPU: LGA4189 Intel 3rd Generation Xeon® Scalable
processors
• BIOS: AMI 256 Mbit SPI BIOS
• Chipset: Intel® C621A PCH
• System Memory: 8* DDR4-2666/2933/3200
Registered ECC DIMM, Max. Capacity 512 GB
Note 2: Due to the inherent limitations of older PC archi-
tectures, the system may not fully detect 512 GB
RAM when 512 GB RAM is installed.
• SATA Interface: 8 x SATA3 6Gb/s ports Intel Rapid
Storage (for Windows only) (SATA0-SATA7 supports
software RAID 0, 1, 10 & 5)
• Serial Ports: One onboard header, only supports RS-232
• Keyboard/Mouse Header (KBMS2): Supports the stan-
dard PS/2 keyboard and mouse via PS/2 cable.
• Watchdog Timer: 255 level timer intervals
• USB Port: Supports up to 6 x USB 3.0 ports (2 ports from
onboard 20-pin header) and 7 x USB 2.0 ports (1*Type-A,
4 ports from onboard 10-pin header)
VGA Interface
• Chipset: ASPEED AST2500/2510
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps & 10 GbE Base-T
• Controller: LAN1/2: Intel I210; LAN3/4: Intel X550
Mechanical and Environment
• Dimensions (L x W): 244 x 304 mm (9.6” x 12”)
• Power Supply Voltage: +3.3 V, +5 V, ±12 V, +5 Vs
• Power Consumption (mainboard only, excluding IO
device): Max. load: +3.3 V @ 13.9754 A, +5 V@ 4.565 A,
+12 V @ 9.406 A,+5 Vsb @ 0.224 A, -12 V@ 0.082 A,
12V_8P @ 25.14 A
• Operating Temperature: 0 ~ 60 °C (depending on CPU)
• Weight: 1.05 kg (weight of board)
SpecicationsPacking List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com
Register your products on our website and get 2
months extra warranty for Free at:
http://www.register.advantech.com
This manual is for the ASMB-816 series Rev. A1
Part No. 2041081600
Printed in China
1st Edition
November 2020
www.coastipc.com | 866-412-6278 | [email protected]

2 ASMB-816 Startup Manual
The board has a number of jumpers that allow you to con-
gureyoursystemtosuityourapplication.Thetablebelow
lists the function of each of the jumpers and connectors.
Connectors
Label Function
ATXPWR1 ATX 24-pin main power connector
ATX12V1, ATX12V2 Processor power connector
(for CPU0)
BH2 For optional battery kit
BIOS_SKT1 BIOS SPI ROM
BMC_CN1, BMC_CN2 IPMI module header
(ASMB-816 I & T2 SKUs only)
COM2 Serial port: RS-232
CPUFAN0 CPU FAN connector
DIMMA1, DIMMB1,
DIMMC1, DIMMD1,
DIMME1, DIMMF1,
DIMMG1, DIMMH1
DDR4 slot
EX_THR1 Connector for external thermistor
GPIO1 GPIO connector
HDAUD1 Audio header
JFP1 Front panel header
KBMS2 External keyboard and mouse
connector (6-pin)
LAN1, LAN2, LAN3_4 RJ-45 LAN connector
LAN5 IPMI dedicated LAN connector
(ASMB-816 I & T2 SKUs only)
LPC2 TPM connector
M2_22110 M.2 connector (SATA & PCIe x4)
PMBUS1 PMBUS connector to communi-
cate with power supply
SATA0~SATA7 SATA connector 0~7
SGPIO1 SATA SGPIO header
PCIEX4_SLOT1 PCIE x4 slot (x4 link) (PCH)
PCIEX16_SLOT2 PCIE x16 slot (x16 link) (CPU)
PCIEX4_SLOT3 PCIE x8 slot (x4 link) (CPU)
PCIEX16_SLOT4 PCIE x16 slot (x16 link) (CPU)
PCIEX1_SLOT5 PCIE x1 slot (x1 link) (PCH)
PCIEX16_SLOT6 PCIE x16 slot (x16 link) (CPU)
PCIEX8_SLOT7 PCIE x8 slot (x8 link) (CPU)
PEHP1 NVMe RAID LED control
Jumpers and Connectors (Cont.)
SLOT12V1 For PCIe slot 12V input only
SMBUS1 SMBus header
SPI_CN1 Connector for BIOS update tool
SPI_SKT1 EC EEPROM
SYSFAN0~SYSFAN4 System FAN connector
USB1_2, USB9_10,
USB13_14
USB 2.0 port 1, 2; USB 2.0 port
9, 10, 13, 14 (9-pin header)
USB11 USB 2.0 port 11 (Type-A)
USB3_12, USB3_34,
USB3_56
USB 3.0 port 1, 2, 3, 4; USB 3.0
port 5, 6 (20-pin header)
VGA1_COM1 VGA + COM connector
VOLT1 Voltage display
VROC1 Intel Virtual RAID (VROC) key
Jumper list
Label Function
JCASE1 Chassis case open alarm
JCMOS1 CMOS clear
JME1 ME update
JTHR_SEL1 To select on board or external thermis-
tor
JWDT1 Watch Dog Reset
PSON1 AT(1-2) / ATX(2-3)
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
Declaration of Conformity
The device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
1 2 3
1 2 3
Jumpers and Connectors

ASMB-816 Startup Manual 3
2.0 mm JFP connector to 2.54 mm Pitch Header
Description Pin Number Description
(Red) PWD BTN ▼1 2 RST BTN (White)
(Black) PWD GND 3 4 PWD GND (Black)
(Blue) LAN1_LED+ 5 6 LAN2_LED+(Brown)
(Red) LAN1_LED- 7 8 LAN2_LED-(Black)
Key
(Orang) HDD_LED+ 13 14 PWR LED+ (Red)
(Black) HDD_LED- 15
Key 16 PWR LED- (Black)
2.0 mm JFP connector on board
Description Pin Number Description
RST BTN 2 ▼1 PWD BTN
PWD GND 4 3 PWD GND
LAN1_LED+ 6 5 LAN2_LED+
LAN1_LED- 8 7 LAN2_LED-
X 10 9 SYS_LED+
GND 12 11 SYS_LED-
PWR LED+ 14 13 HDD_LED+
PWR LED- 16 15 HDD_LED-
Figure 1: Board Layout: Jumper and Connector Locations
Installation Note
Board Layout