Advantech ASMB-820I Installation and operation manual

ASMB-820I Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 ASMB-820I Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file.Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
ASMB-820I Intel® Xeon® E5-2400 series LGA 1356 Socket ATX
Server Board with 4 PCIe & 2 PCI Expansion Slots
Startup Manual
Standard SBC Functions
• CPU: LGA1356 Intel ® Xeon® E5-2400 series
• BIOS: AMI 64 Mb SPI BIOS
• Chipset: Intel® C602J
• System memory: 6* DDR3 REG/ECC/Non-ECC
1066/1333/1600 unbuffered DIMM, Max. 96 GB
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 96 GB RAM
when 96 GB RAM is installed.
• SATA Interface: 4 SATA2 3 Gb/s ports, 2 SATA3 6Gb/s,
supports Intel Matrix Storage (for Windows only) software
RAID 0, 1, 10 & 5.
• Serial ports: Two serial ports, only support RS-232
• Keyboard/mouse connector: Supports standard PS/2
keyboard and mouse
• Watchdog timer: 255 level timer intervals
• USB 2.0: Supports up to eleven USB 2.0 ports (2* Type-
A)
VGA Interface
• Chipset: Aspeed AST2300
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:Intel 82579LM; LAN2: Intel 82574L;
LAN3: Realtek 8201EL(10/100Mbps for IPMI,ASMB-820I
sku only)
Mechanical and Environmental
• Dmensions (L x W): 304 x 244 mm (12” x 9.6”)
• Power supply voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
• Power consumption(Main board only, excluded IO
device): Max. load: +3.3 V @ 24.75 A, +5 V@ 16.77 A,
+12 V @ 13.06 A, +12 V(8P) @ 22 A, +5 Vsb@ 2 A
• Operating temperature: 0 ~ 60° C (depending on CPU)
• Weight: 1 kg (weight of board)
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the ASMB-820I series Rev. A1
Part No. 2006820I10
Print in China
1st Edition,
Feb. 2012

2 ASMB-820I Startup Manual
JCMOS1/JME1: CMOS clear/ME update function
Closed pins
Result
1-2 Keep CMOS data/Disable ME update*
2-3
Clear CMOS data/Enable ME update
*: Default
JWDT1: Watchdog timer function selection
Pins
Result
1-2 Enable*
2-3
Disable
*: Default
**Note: To enable WDT function must to be set as Enable
both in Jumper & BIOS setting.
Enable Disable
1 2 3
1 2 3
Installation Note
JFP1
Pin.1 #PWR_SW
Pin.3 GND
Pin.2 #RST_SW
Pin.4 GND
*Power button pin is located in Pin 1 & 3 of front panel
connector
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each jumper and connector.
Connector list
Label Function
ATX24P_P1 ATX 24 Pin main power con-
nector
ATX8P_P0 Processor power connector(for
CPU0)
SATA0~SATA5 Serial ATA0~5
USB45,USB67,
USB89 USB port 4,5,6,7,8,9 (Header)
USB01,USB23
USB10,USB11
USB port 0,1,2,3,10 & 11(type
A)
DIMMA1 ~ DIMMC1 DDR3 slot
CPUFAN0 CPU FAN connector
SYSFAN0,SYSFAN1,
SYSFAN2,SYSFAN3 System FAN connector
LAN1,LAN2 LAN connector
BMC LAN1 LAN connector for IPMI
VGA_COM1 VGA+COM connector
KBMS1 Keyboard and mouse connector
KBMS2 External keyboard and mouse
connector(6 pin)
BIOS_SKT1 BIOS SPI ROM
LANLED1 LAN LED extension connector
SMBUS1 Front panel SMBus header
IPMI1 IPMI header
SATA_SGPIO_1 SATA SGPIO header
AUDIO1 Audio header
COM2 Serial port: RS-232
JFP1 Front panel header
Jumper list
Label Function
JCMOS1 CMOS clear
JME1 ME update
JWDT1 Watch dog selection
Jumpers and Connectors
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
1 2 3
1 2 3
Jumpers and Connectors

ASMB-820I Startup Manual 3
The CD disc contains a driver installer program that will lead
you through the installation of various device drivers needed
to take full advantage of your motherboard.
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used bat-
teries according to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Software Installation Declaration of Conformity
Board Layout: Jumper and Connector Locations
Board Layout
PCIEx16_SLOT6
SYS
FAN3
IPMI
LAN1
LAN1_
USB01
LAN2_
USB23 COM1
+ VGA1
KBMS1
KBMS2
ATX8P_P1
PMBUS1
ATX 24P_P1
CPU0
DIMM A1
DIMM B1
CPU
FAN0
SYS
FAN0
SYS
FAN2
2 SATA III
4 SATA II
USB10
USB67
JFP1
SATA
_SGPIO1
LPC1
IPMI1
COM2
AUDIO 1
FP SMB1
DIMM A2
DIMM B2
DIMM C1
DIMM C2
SYS
FAN1
PCIEx1_SLOT5
PCIEx16_SLOT4
PCIEx4
_SLOT3
PCI_SLOT2
PCI_SLOT1
USB11
USB45
USB89