Advantech ASMB-823I Installation and operation manual

ASMB-823I Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 ASMB-823I Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 2 CPU power cables (8P)
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
ASMB-823I Intel Xeon® E5-2600v3 Series ATX Server
Board with DDR4, 4 PCIe x16, 6 USB 3.0, 9 SATA3
Startup Manual
Standard M/B Functions
• CPU: Dual LGA2011-R3 Intel Xeon® E5-2600v3 series
• BIOS: AMI 128 Mb SPI BIOS
• Chipset: Intel® C612 PCH
• System Memory: 6* DDR4-1600/1866/2133 Registered
ECC DIMM, Max. Capacity 192 GB
Note 2: Due to the inherent limitations of the PC archi-
tecture, the system may not fully detect 192 GB
RAM when 192 GB RAM is installed.
• SATA Interface: 9 SATA3 6 Gb/s ports Intel Rapid
Storage (for Windows only) (SATA0-SATA4 and sSATA0-
sSATA3 Supports software RAID 0, 1, 10 & 5)
• Serial Ports: One onboard header, only support RS-232
• Keyboard/Mouse Header (KBMS2): Supports the stan-
dard PS/2 keyboard and mouse via PS/2 cable
• Watchdog Timer: 255 level timer intervals
• USB Port: Supports up to 6 USB 3.0 ports (2 ports from
onboard 20-pin header) and 3 USB 2.0 ports (1*Type-A, 2
ports from onboard 10-pin header)
VGA Interface
• Chipset: Aspeed AST2400/1400
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1: Intel I210; LAN2: Intel I210
Mechanical and Environment
• Dimensions (L x W): 244 x 304 mm (9.6” x 12”)
•Power Supply Voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
•Power Consumption (mainboard only, excluding IO
device): Max. load: +3.3 V @ 1.67 A, +5 V@ 0.85 A, +12 V
@ 18.11 A,+5 Vsb@ 0.05 A, -12 V@ 0.004 A
•Operating Temperature: 0 ~ 40° C (depending on CPU)
•Weight: 1 kg (weight of board)
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com
This manual is for the ASMB-823I series Rev. A1
Part No. 2006823I10
Print in China
1st Edition
October 2014

2 ASMB-823I Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application.
The table below lists the function of each of the jumpers and
connectors.
Connectors
Label Function
ATXPWR1 ATX 24 Pin main power connector
ATX12V1 Processor power connector
(for CPU0)
ATX12V2 Processor power connector(for
CPU1)
SLOT12V1 For PCIe slot 12V input only
SATA0~SATA4
sSATA0~sSATA3
Serial ATA0~4, Slave serial
ATA0~3
USB6_7 USB 2.0 header 6, 7
USB10 USB 2.0 port 10 (Type-A)
USB0_1, USB2_3,
USB4_5
USB 3.0 port 0, 1, 4, 5; USB 3.0
port 2, 3 (20-pin header)
SLOT1 PCIE x8 slot (x4 link) (PCH)
SLOT2 PCIE x16 slot (CPU1)
SLOT3 PCIE x8 slot (CPU1)
SLOT4 PCIE x16 slot (CPU0)
SLOT5 PCIE x16 slot (CPU1)
SLOT6 PCIE x16 slot (CPU0)
SLOT7 PCIE x8 slot (CPU0)
DIMMA1, DIMMA2,
DIMMB1, DIMMG1,
DIMMG2, DIMMH1
DDR4 slot
CPUFAN0,CPUFAN1 CPU FAN connector
SYSFAN0,SYSFAN1,
SYSFAN2 System FAN connector
LAN1,LAN2 RJ-45 LAN connector
VGA1 VGA connector
KBMS2 External keyboard and mouse
connector (6 pin)
BIOS1 BIOS SPI ROM
LANLED1 LAN LED extension connector
SYS_LED1 System LED connector
SMBUS1 SMBus header
BMC1, BMC2 IPMI module header
SGPIO1, SGPIO2 SATA SGPIO header
Jumpers and Connectors
Jumpers and Connectors
JCASE1 Chassis case open alarm header
HDAUD1 Audio header
COM2 Serial port: RS-232
JFP1, JFP2, JFP3 Front panel header
GPIO1 GPIO connector
PMBUS1 PMBUS connector
VOLT1 Voltage monitoring connector for
Intelligent System module
EX_THR1 Connector for external thermistor
SPI_CN1 Connector for BIOS update tool
LPC1 TPM connector
Jumper list
Label Function
JCMOS1 CMOS clear
JME1 ME update
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
JFP1, JFP2
Pin.3 #PWR_SW
Pin.6 GND
Pin.9 #RST_SW
Pin.12 GND
Pin.8, Pin.11 HWM_SMB_DATA, HWM_SMB_CLK
*Power button pin is located in Pin 3 & 6 of front panel
connector
1 2 3
1 2 3
Installation Note
3 6 9 12 PWRSW RESET
HDDLED
SNMP
JFP1
&
1(+) 4 7 10(-)
HDDLED
SM_BUS
SPEAKER
JPF2
&
PWRLED & KEYLOCK
1(+) 23(-) 45JFP3
2(+) 5(-) 8 11

ASMB-823I Startup Manual 3
The device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
The CD disc contains a driver installer program that will lead
you through the installation of various device drivers needed
to take full advantage of your motherboard.
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used bat-
teries according to manufacturer’s instructions.
Software Installation Declaration of Conformity
Board Layout
Figure 1: Board Layout: Jumper and Connector Locations
PCIEx16_SLOT6
PCIEx16_SLOT5
CPU
FAN1
LAN1_2
USB4_5
USB0_1
VGA1
KBMS2
ATX12V2
DIMM H1
DIMM G1
CPU1
PMBUS1
ATXPWR1
CPU0
DIMMA2
DIMMA1
ATX12V1
CPU
FAN0
DIMMB1
SYS FAN2
JFP1
JFP2
JPF3
HDAUD 1
JCASE1
JCMOS1
PCIEx8_SLOT7
PCIEx16_SLOT2
BMC1
SYS
FAN0
SMBUS1
SYS
FAN1
GPIO1
USB6_7
COM2
PCH
PCIEx8_SLOT1
PCIEx8_SLOT3
PCIEx16_SLOT4
sSATA0, 2, 3
sSATA1
JTHR_SEL1 & JME1
17
SATA0-4
SYS_LED1
USB2_3
SGPIO1 & 2
SP1_CN1
EX_THR1
VOLT1
LANLED1
DIMM G2
BMC2
USB10
SLOT12V1
BIOS1
LPC1