Advantech ASMB-817 Series Installation and operation manual

ASMB-817 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x ASMB-817 Startup Manual
• 2 x SATA data cables
• 2 x SATA power cables
• 2 x CPU power cables (8P)
• 1 x CPU carrier
• 1 x I/O port bracket
• 1 x M.2 screw
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Standard M/B Functions
• CPU: LGA4677 Intel 4th Generation Xeon®Scalable
processors
• BIOS: AMI 512 Mbit SPI BIOS
• Chipset: Intel®C741 PCH
• System Memory: 8* DDR5 4400/4800
Registered ECC DIMM, Max. Capacity 512 GB
Note: Due to the inherent limitations of older PC archi-
tectures, the system may not fully detect 512 GB
RAM when 512 GB RAM is installed.
ASMB-817 Series LGA 4677 Intel 4th Generation Xeon®
Scalable ATX Server Board with 8 DDR5, 3 PCIe x16,
8 SATA3, 4 USB3.2 (Gen1), Dual 10GbE, IPMI
Startup Manual
• SATA Interface: 8 x SATA3 6Gb/s ports Intel Rapid
Storage (for Windows only) (SATA0-SATA7 supports
software RAID* 0, 1, 10 & 5) * Limited support
• Serial Ports: One onboard header, only supports RS-232
• Keyboard/Mouse Header (KBMS1): Supports the stan-
dard PS/2 keyboard and mouse via PS/2 cable.
• Watchdog Timer: 255 level timer intervals
• USB Port: Supports up to 4 x USB 3.2(Gen1) ports (2
ports from onboard 20-pin header) and 9 x USB 2.0 ports
(1*Type-A, 4 ports from onboard 10-pin header)
VGA Interface
• Chipset: ASPEED AST2600
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps & 10 GbE Base-T
• Controller: LAN1/2: Intel I210; LAN3/4: Intel X710
Mechanical and Environment
• Dimensions (L x W): 244 x 304 mm (9.6” x 12”)
• Power Supply Voltage: +3.3 V, +5 V, +12 V, +5 Vsb
• Power Consumption (mainboard only, excluding IO
device): Max. load: +3.3 V @ 1.239 A, +5 V@ 1.314 A,
+12 V @ 0.052 A,+5 Vsb @ 0.7 A, 12 V_8P @ 20.833 A
• Operating Temperature: 0 ~ 60° C (depending on CPU)
• Net Weight: 0.97 kg
The board has a number of jumpers that allow you to con-
gureyoursystemtosuityourapplication.Thetablebelow
lists the function of each of the jumpers and connectors.
Connectors
Label Function
ATXPWR1 ATX 24-pin main power connector
ATX12V1, ATX12V2 Processor power connector (for CPU0)
BH2 For optional battery kit
BIOS_SKT1 BIOS SPI ROM
COM2 Serial port: RS-232
CPUFAN0 CPU FAN connector
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com
Register your products on our website and get 2
months extra warranty for Free at:
http://www.register.advantech.com
This manual is for the ASMB-817 series Rev. A1.
Part No. 2042081700
Printed in China
1st Edition
January 2023
Specications(Cont.)
Jumpers and Connectors

2 ASMB-817 Startup Manual
DIMMA1, DIMMB1,
DIMMC1, DIMMD1,
DIMME1, DIMMF1,
DIMMG1, DIMMH1
DDR5 slot
EXT_THR1 Connector for external thermistor
GPIO1 GPIO connector
HDAUD1 Audio header
KBMS1 External keyboard and mouse
connector (6-pin)
LAN1_USB2C1,
LAN2_USB2C2,
LAN3_4
RJ-45 LAN connector
BMCLAN_USB3C1 IPMI dedicated LAN connector
SPI_TPM1 TPM connector
M2_22110_1 M.2 connector (SATA & PCIe x4)
PMBUS1 PMBUS connector to communicate with
power supply
SATA0~SATA7 SATA connector 0~7
SGPIO1,SGPIO2 SATA SGPIO header
PCIEX1_SLOT1 PCIE x1 slot, close end (x1 link) (PCH)
PCIEX16_SLOT2 PCIE x16 slot (x16 link) (CPU)
PCIEX4_SLOT3 PCIE x4 slot, close end (x4 link) (CPU)
PCIEX16_SLOT4 PCIE x16 slot (x16 link) (CPU)
PCIEX8_SLOT5 PCIE x8 slot, open end (x8 link) (CPU)
PCIEX16_SLOT6 PCIE x16 slot (x16 link) (CPU)
PCIEX8_SLOT7 PCIE x8 slot, close end (x8 link) (CPU)
SLOT12V1 For PCIe slot 12V input only
SMBUS1 SMBus header
SPI_CN1 Connector for BIOS update tool
BMC_SPI1 BMC EEPROM
SYSFAN0~
SYSFAN4 System FAN connector
LAN1_USB2C1,
LAN2_USB2C2,
USB2H1,USB2H2
USB 2.0 port 1,2,3,4; USB 2.0 port 9, 10,
13, 14 (9-pin header)
USB2A1 USB 2.0 port 11 (Type-A)
BMCLAN_USB3C1
USB3H1
USB 3.2(Gen1) port 1, 2; USB 3.2(Gen1)
port 3, 4 (20-pin header)
VGA1_COM1 VGA + COM connector, Serial: RS-232
VOLT1 Voltage display
ESPI1 eSPI connector for TPM module
SYS_LED System LED connector
LANLED1 LAN LED connector
Jumpers and Connectors (Cont.)
Jumper list
Label Function
JCASE1 Chassis case open alarm
JCMOS1 CMOS clear
JFP1, JFP1+JFP12 Front panel header
JME1 ME update
JTHR_SEL1 To select on board or external thermistor
JWDT1 Watch Dog Reset
PSON1 AT(1-2)/ATX(2-3), default (2-3)
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/ Clear CMOS data/
Disable ME update Enable ME update
The device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
JFP1+JFP12
Pin.3 #PWR_SW
Pin.6 GND
Pin.9 #RST_SW
Pin.12 GND
Pin.8, Pin.11 HWM_SMB_DATA, HWM_SMB_CLK
*Power button pin is located in Pin 3 & 6 of front panel connector.
1 2 3
1 2 3
JFP12
JFP12
Jumpers and Connectors
Declaration of Conformity
Installation Note

ASMB-817 Startup Manual 3
2.0 mm JFP1 connector to 2.54 mm pitch header
Description Pin Number Description
(Red) PWD BTN ▼1 2 RST BTN (White)
(Black) PWD GND 3 4 PWD GND (Black)
(Blue) LAN1_LED+ 5 6 LAN2_LED+(Brown)
(Red) LAN1_LED- 7 8 LAN2_LED-(Black)
Key
(Orang) HDD_LED+ 13 14 PWR LED+ (Red)
(Black) HDD_LED- 15
Key 16 PWR LED- (Black)
2.0 mm JFP1 connector on board
Description Pin Number Description
RST BTN 2 ▼1 PWD BTN
PWD GND 4 3 PWD GND
LAN1_LED+ 6 5 LAN2_LED+
LAN1_LED- 8 7 LAN2_LED-
X 10 9 SYS_LED+
GND 12 11 SYS_LED-
PWR LED+ 14 13 HDD_LED+
PWR LED- 16 15
HDD_LED-
Figure 1: Board Layout: Jumper and Connector Locations
ATXPWR1
ATX12V1
ATX12V2
JCMOS1
JME1
COM2
VGA1_COM1
CPUFAN0
GPIO1
SGPIO 1/2
HDAUD1
JCASE1
LAN1_
USB2C1
LAN2_
USB2C2
BMCLAN_
USB3C1
LAN3_4
ESPI1
SPI_TPM1
PCIEX16
_SLOT2
PCIEX16
_SLOT4
PCIEX16
_SLOT6
PCIEX1
_SLOT1
PCIEX4
_SLOT3
PCIEX8
_SLOT5
PCIEX8
_SLOT7
JTHR_SEL1 /
EXT_THR1
SYSFAN1
SYSFAN0
SYSFAN2
SYSFAN3
VOLT1
JFP1
+JFP12
USB2H1
SYS_LED
SMBUS1
PSON1
USB2H2
USB3H1
KBMS1
USB2A1
LANLED1
PMBUS1
Intel LGA4677 CPU1
DIMMA1
DIMMB1
DIMMC1
DIMMD1
DIMME1
DIMMF1
DIMMG1
DIMMH1
BIOS_SKT1
SPI_CN1
BMC_
SPI1
SYSFAN4
SLOT12V1
M.2_22110_1
BZ1
SATA0
SATA1
SATA2
SATA3
SATA4
SATA5
SATA6
SATA7
BH2
BH1
JFP1
Installation Note (Cont.)
Board Layout
Installation Note (Cont.)