VIBIA Wind User manual

VIBIA LIGHTING, S.L.U. Barcelona, 72 - 74. 08820 El Prat de Llobregat (Barcelona - Spain). Tel [phone]. Fax [phone].
[email protected] www.vibia.com
WIND
Design von Jordi Vilardell.
Referenz
4055.
Anwendung
Außenleuchten
Installationstyp
Aufbau
Beschreibung
Stehleuchte für den Außenbereich. Das Design von Jordi Vilardell ist in Grün, Orange, Weiß
und Schwarz verfügbar. Durch die Wahl des Materials – mittels innovativen
Filament-Winding-Verfahrens industriell hergestellte Glasfasern – werden bei dieser
Kollektion Technik und Tradition gekonnt miteinander verbunden.
Diffusor
Diffuser aus Metacrylat
Finish
4055-03.
Weiss
4055-04.
Schwarz
4055-07.
Grün
4055-08.
Orange
Skizze
Elektrische Eigenschaften
1 x 2GX13 230V 40W (T5C) Total 40,0 W
Physische
2 Box / 0,60 x 0,60 x 2,11 m. / Vol. 1,0300 m³ /
Bruttogewicht 45,1 kg. / Nettogewicht 27,8 kg.
Installation und Montage
Den Anweisungen der Installationsanleitung folgen
Lichtverteilung
Allgemeine Beleuchtung
Beleuchtungskörper für die allgemeine Beleuchtung, der das Licht gleichmäßig in alle
Richtungen verteilt.
Fotometrische Daten
Effizienz : 30.72%
Koordinatensyst. : C-G
Gesamtfluss : 3200.00 lm
Maximalwert : 124.39 cd/klm
Maximalwert : C=0.00 G=0.00
Bi-symetrisch : 3
Isolux (Boden) : Isolux (Suelo)
Position Lichtquelle :
X=0.00m Y=0.00m Z=1.90m
Rotation Lichtquelle :
Zertifikate

1.
4055
1 Shade's screws 4 un.
2 Allen key 2 un.
3 Lamp structure 1 un.
4 Shade 1 un.
2.
3.
4.
Wind
Design by Jordi Vilardell
ASSEMBLY I STRUCTIO S
SUPPLIED MATERIAL
4055. et Weight 27,8 Kg
1 x T-5 Circline 2GX13 40W
Class I. Product with an additional protection cable (grounds).
Dust-tight product. Protected against water spray.
Product that CA be in contact with normally-flammable materials
(wood or others).
-If you wish to fix the lamp to the ground, choose the most adequate plugs and screws depending on the surface.
-Before the installation, make sure the installation surface will not be damaged. If this happens, it will be the installator´s responsibility.
-If the steel cable or the power cord of this lamp is damaged, it must be replaced only by the manufacturer or their technical service or by a person capacitated to this effect to avoid
any risk.
Caution
Before assembling and installing this roduct, carefully read the following:
-Switch of the mains before installing the lamp.
-Always use the recommended bulb
TECH ICAL SPECIFICATIO S

1
2
3
4
st
1
3r d
2nd
A
B
C
D
A
st
1
3rd
2nd
A
B
C
D
E
F
OTE
: Please, follow these instructions just in case you need to fix the lamp to the ground. If you
do not need it to be fixed to the ground, skip steps 1 through 3 and go directly to step 4.
1. Disassemble the base (A) as follows:
Remove the two screws (B) using the supplied Allen wrench.
Hold the lamp (C) firmly and move it toward the cable (as shown by the arrow) until it comes
loose from the fixing plate (D).
Pull upwards to completely release it from the base (A)
Important: Do not do this if the lamp is leaning or lying on the ground. It must be vertical.
2. Fix the base (A) to the ground using the most adequate screws and plugs (not supplied).
3. Replace the lamp (C) following the instruction of step 1 backwards, making sure the lamp is
firmly joined to the anchorage device (D), and fix it in place by tightening the screw (B) with
supplied allen key.
4. After installing the fluorescent bulb, fix the shade (E) in place using its 4 screws (F) (supllied in
a bag), using the supplied Allen wrench.
ASSEMBLY I STRUCTIO S
Maintenance
-Use a slightly-wet cotton cloth for cleaning.
-In case of malfunction or damage, please contact the retailer who sold the lamp.