Aervoe 1154 User manual

LED BATON
ROAD FLARE
ON/OFF BUTTON
MAGNET IN
HANDLE BASE
MAGNET
CHARGING INPUT CONTACTS
BACK
FRONT
HOOK
Aervoe® LED Baton Road Flare #1154 & 1155
IMPORTANT SAFEGUARDS
Read all instructions before operating•
Do not look directly at the light; may cause injury to your eyes•
Never use if wiring or circuits are exposed or damaged•
Turn off all lights before charging•
Do not use alcohol, flammable solutions, or other solvents on or near this unit. Only clean with•
warm water and a soft cloth.
Administer close supervision when using around children•
Waterproof only when used in accordance with manufacturer’s instructions•
PARTS IDENTIFICATION
CHARGING
The Flare may be charged using either a 12V car charger, 120V wall charger, or USB adapter (included).
Plug the1. USB PLUG into the appropriate 12V or 120V CHARGING ADAPTER, depending on your
application, or directly into your computer or other USB charging device.
Plug the male end of the2. USB CABLE into the female port of the MAGNETIC CONNECTOR HUB.
Connect the MAGNETIC CONNECTOR3. HUB to the FLARE aligning the (+) and (-) terminal symbols on
each. The MAGNET in the center and the divots in the screws will keep the two items connected and
aligned.
Plug the 12V or 120V C4. HARGING ADAPTER into either a 12V power receptacle or 120V wall outlet.
Green LED = charge in process•
Red LED = fully charged OR the Flare and Hub are misaligned and need to be adjusted•
OPERATION
Press the ON/OFF BUTTON to rotate through the following 9 light patterns:
#1 - Rotate
#2 - Quad Flash
#3 - Alternating Blinks
#4 - SOS Rescue (Morse Code)
#5 - Steady on - high
#6 - Off
Alternate Operation:
To turn off the flare without cycling through the 5 light patterns, press and hold the ON/OFF BUTTON for 2
seconds. One LED will flash five times and then turn off. When ready to operate again, press the ON/OFF
BUTTON and it will return to the last flash pattern that was selected before turning off.
RANGE OF USE
Emergency Road Flare1.
Replaces standard incendiary flares•
Use to alert drivers to potential roadside danger, mark detours, signal for help,•
Safety Wand2.
Use as a hand-held signaling device to direct traffic (vehicle, crowds, aviation, marine), signal for•
help
Used by emergency services, airport ground crews, road construction crews and personal•
vehicle safety
Features3.
Safer and ecologically better for our environment than flame style emergency road flares. No•
spark, open flame, fumes or toxic chemicals are produced when using as a road flare.
Shock resistant construction makes it very durable and can withstand the impact of roadside•
traffic. Can even be run over by a truck and still operate. Used by fire, police, and other
emergency responders.
Waterproof so it may be used for marine applications and safely in wet environments, including•
submerged to a depth of 50 feet. Will float unless secured.
Using the magnet on the back or handle end, attach to any ferrous metal surface. Place on a•
vehicle, fence, or other metal surface.
Lie flat or upright on it’s handle end for vertical placement. Place on the road, at construction•
sites, vehicle bumper or other surface, and anywhere needing emergency signaling.
Optional Flex-Fit Tripod #1159 is available to hold Flares in a vertical position for greater visibility,•
even on uneven ground. Contact your local retailer or www.aervoe.com.
NOTE: It is not recommended that you disassemble the Flare. If it is not reassembled correctly it may result
in failure of the waterproof seal and damage to the unit.

OPERATING INSTRUCTIONS
TECHNICAL INFORMATION
SPECIFICATIONS
INTERNAL RECHARGEABLE BATTERY Lithium Ion
CHARGING SPECIFICATIONS
120V AC/DC CHARGER:
(CE & C/UL Listed)
12V DC CHARGER:
(CE)
Input: 100-240V AC, 50-60 Hz 0.15A
Output: 5.0 V DC 1200 mAh
Input: 12-24V DC
Output: 5.0V DC 850 mAh
TEMPERATURE RANGE -32ºF TO 240ºF (-36ºC - 116ºC)
DOT & TRAFFIC SAFETY COMPLIANCE U.S. DOT (FMCSA) 49 CFR1. § 392.25 & 393.95 (g)
(prohibits the carrying of any flame-producing flare
on any Commercial Motor Vehicle (CMV) transporting
explosives; any cargo of flammable liquid or flammable
compressed gas, whether loaded or empty; or any CMV
using compressed gas as a motor fuel).
MUTCD Type A (flashing) and Type C (solid on)2.
NFPA 1901 Standards for Traffic Safety; Section 6.7.33.
Miscellaneous Equipment
WEIGHT 8 oz.
DIMENSIONS 10.75” L x 1.75” W x 1.375” H
POWER DURATION RUN TIME
The battery will be fully charged with either charger
within 4-6 hours. When fully charged you may expect
these run times:
#1 - Rotate 5 hours
#2 - Quad Flash 10 hours
#3 - Alternating Blinks 3 hours
#4 - SOS Rescue (Morse Code) 10 hours
#5 - Steady on - high 4 hours
NOTE: The stand-by charging feature allows flares to be kept plugged in when not in use without damage
to the battery or unit. Ensures the flares will be charged and ready for use when needed. Flares will keep
a full charge for 90 days.
AERVOE INDUSTRIES INCORPORATED
Gardnerville, NV 89410 • 1-800-227-0196
www.aervoe.com • [email protected]
1154/1155inst; cs9/10
LED Baton
Road Flare
Patent Pending