Mustang Survival DLX 38 User manual

FOR MODEL NUMBERS MD2951 (MANUAL) / MD2953 (AUTO)
OWNER'S MANUAL
DLX 38 INFLATABLE PFD
DO NOT REMOVE PRIOR TO SALE.
HT1182 REV. 31JAN2017

TABLEOFCONTENTS
INFLATABLE PFDS...................................................................................... 4
APPROVAL CONDITIONS AND CARRIAGE REGULATIONS .............. 4
MANDATORY CARRIAGE REQUIREMENTS ......................................... 4
WHY ARE PFDS REQUIRED SAFETY EQUIPMENT? .............................. 5
WHAT IS AN INFLATABLE PFD?............................................................... 5
INSTRUCTIONS FOR USE .......................................................................... 5
COMPONENT INSPECTION INSTRUCTIONS........................................ 6
READINESS CHECKLIST ........................................................................ 6
SIZING AND FIT...................................................................................... 7
DONNING INSTRUCTIONS......................................................................... 7
INFLATING YOUR INFLATABLE PFD........................................................ 8
INFORMATION ........................................................................................ 9
SPECIAL CONSIDERATIONS FOR AUTOMATIC DEVICES
(MD2953)....................................................................................................10
DEFLATING THE INFLATABLE PFD..........................................................11
RE-ARMING YOUR MANUAL PFD (MD2951) .........................................12
RE-ARMING YOUR AUTOMATIC PFD (MD2953)...................................14
REPACKING ................................................................................................17
IS YOUR PFD IN GOOD AND SERVICEABLE CONDITION? .................19
USAGE BELOW FREEZING .......................................................................19
CARE AND MAINTENANCE INSTRUCTIONS..........................................19
CLEANING AND STORING YOUR PFD...................................................20

3
HOW AND WHY TO TEST YOUR PFD.....................................................21
HOW DO YOU TEST YOUR PFD USING THE
AUTOMATIC INFLATOR?.......................................................................... 22
HOW DO YOU TEST YOUR PFD USING THE MANUAL INFLATOR?... 22
HOW DO YOU TEST YOUR PFD USING THE ORAL INFLATOR?........ 23
WEAR YOUR PFD ..................................................................................... 23
HYPOTHERMIA..........................................................................................24
HOW HYPOTHERMIA AFFECTS MOST ADULTS............................... 24
EACH OF THESE DEVICES IS INTENDED TO HELP YOU
SAVE YOUR OWN LIFE ............................................................................ 25
INFLATABLE PFD SAFETY ACCESSORIES ............................................ 26
ADDITIONAL INFORMATION ..................................................................26
DO NOT ATTACH PFD’S TO YOUR BOAT .............................................. 26
AIRLINE OPERATOR POLICY ON CARRIAGE OF
INFLATABLE PFDS AND CO2CARTRIDGES ..........................................26

4 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
WARNING - MODEL MD2951 WILL NOT INFLATE AUTOMATICALLY UPON IMMERSION.
TAB MUST BE PULLED TO ACTIVATE INFLATION MECHANISM.
INFLATABLEPFDS
Inflatable PFDs are special devices in that the flotation of the wearer
is not derived from inherently buoyant materials. In order for them
to do their job, you, the wearer, must do yours! This means you have
the responsibility to ensure you are familiar with the operation and
maintenance requirements of your inflatable PFD! You must also
be aware of the limitations of the device and know that it is not
approved under the Small Vessel Regulations for certain boating
activities.
READ YOUR OWNER’S MANUAL AND THE INFORMATION LABELS ON YOUR PFD! IT
COULD SAVE YOUR LIFE!
APPROVAL CONDITIONS AND CARRIAGE REGULATIONS
This inflatable PFD is approved by Transport Canada for use as a Type
II (MD2953) or Type III (MD2951) Personal Flotation Device (PFD).
It is not approved for water skiing or other high impact, high speed
activities. This inflatable PFD was designed to be more comfortable
and less restrictive to wear than inherently buoyant PFDs. When
worn, used, and serviced according to this owner’s manual, this
PFD can greatly increase your chances of survival in the water.
Not recommended for non-swimmers or weak swimmers. Users of
inflatable PFDs must be at least 16 years old.
MANDATORY CARRIAGE REQUIREMENTS
The Small Vessel Regulations require that you carry on board a
Transport Canada approved personal flotation device, which bear a
mark or label indicating the approval and is of an appropriate size for
each person on board. To be considered serviceable, this Inflatable
PFD shall not exhibit deterioration that could diminish its performance
such as broken or deformed hardware, detached webbing, rotted
structural components, air leaks, or nonfunctional oral inflation
tube. Unless worn inflated, this Inflatable PFD must also be properly
armed with a full CO2cylinder, inflation system status indicator, and
an accessible manual inflation lanyard. A PFD which is “approved
only when worn” or “required to be worn” must be worn under the
specified conditions.

5
WHY ARE PFDS REQUIRED SAFETY EQUIPMENT?
Drownings are the leading cause of fatalities involving recreational
boating. A PFD provides flotation to help keep your head above
water, help you to stay face up in the water, and increase your
chances for survival and rescue. Most adults only need an extra 3.2 to
5.5 kg (7 to 12 pounds) of flotation to keep their heads above water.
The proper size PFD will properly support the weight of the wearer.
Since this Inflatable PFD does not have inherent buoyancy, it provides
flotation only when inflated. Familiarize yourself with the use of this
Inflatable PFD so you know what to do in an emergency.
WHAT IS AN INFLATABLE PFD?
While traditional PFDs are inherently buoyant, inflatable PFDs rely
entirely on inflation for buoyancy. Uninflated, the Inflatable PFD
is a comfortable slim collar that can be inflated at any time with
a 33-gram CO2gas cylinder. The Inflatable PFD is designed to
offer maximum mobility with minimum bulk. The Inflatable PFD
MD2951 can be inflated either manually by jerking a pull-tab, or
orally by mouth. The Inflatable PFD MD2953 can be inflated either
automatically during water immersion, manually by jerking a pull-tab,
or orally by mouth. It is recommended that you familiarize yourself
with the procedures outlined in Instructions For Use (below).
INSTRUCTIONS FOR USE
This manual supplies instructional, maintenance and safety
information for all models (MD2951 and MD2953) unless specified
otherwise. The model number is listed on the underside label.
MD2953 Service Indicator
Automatic Inflator
Velcro
Strip
MD2951 Service Indicator
Manual Inflator
Velcro
Strip
Fig. 1
MD2953 Service Indicator
Automatic Inflator
Velcro
Strip
MD2951 Service Indicator
Manual Inflator
Velcro
Strip
Fig. 2

6 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
COMPONENT INSPECTION INSTRUCTIONS
1. Examine the service indicator through the window panel
(Fig. 1 and 2). Ensure the service indicator is green. If the service
indicator is red, the mechanism has been fired or is incorrectly
fitted (see Re-arming Your PFD (for your model)).
NOTE: THE SERVICE INDICATOR MUST BE GREEN BEFORE PROCEEDING.
2. Undo the Velcro™ strips along both sides of the PFD (Fig. 1 and 2).
3. Ensure the oral-inflation dust cap is in the stowed position
(Fig. 12).
4. Ensure the service indicator is green and the pull-tab lanyard is
hanging on the outside; secure the Velcro™ strips on both sides of
the Inflatable PFD.
5. For MD2953 only - Ensure the bobbin is valid. The PFD, or bobbin,
must have been purchased within the last three (3) years. If the
purchase date is unknown, check the date printed on the bobbin
and replace if older than three (3) years (see "Re-arming Your
Automatic PFD (MD2953)" on p.14).
READINESS CHECKLIST
Check your Inflatable PFD and ensure all of the checkpoints listed
below are true before use.
Service indicator is green (Fig. 1 and Fig. 2).
No rips, tears or holes; all seams are securely sewn; and the
fabric, straps and hardware are still strong.
All Velcro™ are securely fastened.
Inflatable PFD is not twisted.
Oral-inflation dust cap is in the stowed position (Fig. 12).
For the MD2953 only - Ensure the bobbin is valid. The PFD, or
bobbin, must have been purchased within the last three (3)
years. If the purchase date is unknown, check the date printed
on the bobbin and replace if older than three (3) years
(see Re-arming Your PFD (MD2953), p.14).
Your Inflatable PFD is ready for use if all applicable boxes are
checked.
NOTE: CONTACT YOUR MUSTANG SURVIVAL DEALER IF YOU HAVE ANY CONCERNS
ABOUT THE READINESS OF YOUR INFLATABLE PFD.

7
SIZING AND FIT
This PFD provides a minimum of 150 N (33.7 lbs) of buoyancy when
inflated and is designed for wearers over 16 years of age, with a chest
range of 76-132 cm (30-52 inches) weighing over 36 kg (80 pounds).
DONNING INSTRUCTIONS
It is important that the Inflatable PFD is properly adjusted to fit
the person wearing it. An incorrect fit or improper fastening of
attachments could impede its effectiveness.
1. All belts and straps are already threaded correctly and only need
to be adjusted for fit. The belt should fit below your rib cage
adjusted to a snug personal fit.
Fig. 3
Fig. 5
Fig. 4
Fig. 6

8 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
2. Put the Inflatable PFD on just like a jacket (Fig. 3-6) and fasten
the front buckle. Adjust the waist belt using two straps from the
left and right side of the body. Pull back the straps to tighten, pull
the adjusters forward to loosen (Fig. 7) Secure the belt's loose
ends in the belt keeper (Fig. 8)
WARNING: DO NOT WEAR INFLATABLE PFDS UNDER CLOTHING AS THE INFLATION
COULD BE RESTRICTED AND YOU COULD BE INJURED.
INFLATING YOUR INFLATABLE PFD
It is recommended that the following procedures be followed to
inflate your Inflatable PFD:
3. Manual Inflation
Activate the inflation system by jerking firmly downward on the
pull-tab (Fig. 9). The Inflatable PFD should fully inflate within 5
seconds.
Loosen
Tighten
Fig. 7
Belt
Keeper
Fig. 8
MD2951 MD2953
Manual Inflator Automatic Inflator
Fig. 9

9
4. Automatic Backup Inflation (MD2953)
Inflation will occur automatically within 10 seconds after the
inflator is immersed in water. The water-sensing bobbin will
disintegrate, triggering a spring-loaded plunger, which punctures
the CO2cylinder (Fig. 16) to inflate the Inflatable PFD.
INFORMATION
When inflated, the carbon dioxide
(CO2gas) used to inflate the
PFD will slowly escape through
the fabric over time. A slight
reduction of pressure will be
observed after several hours
of inflation. Topping up by oral
inflation may be required in
the event of very prolonged
immersion.
IMPORTANT: SEE SPECIAL
CONSIDERATIONS FOR AUTOMATIC
DEVICES (P.10)
5. Oral Inflation
Properly armed and inspected Inflatable PFDs will inflate when
manually or automatically activated. However, you can fully inflate
the Inflatable PFD by mouth (Fig. 10) should inflation not occur,
or if you are in a non-emergency situation. To orally inflate the
Inflatable PFD, first locate the oral inflation tube by opening the
wearer ’s left front panel of the Inflatable PFD. Remove the dust
cap from the end of the oral tube and blow into the tube until the
Inflatable PFD is fully inflated.
Place the oral inflator dust cap back in the stowed position
(Fig. 12)
IMPORTANT: DOUBLE INFLATION
DO NOT MANUALLY OR AUTOMATICALLY ACTIVATE THE INFLATOR WHEN YOUR PFD IS
FILLED WITH AIR. DOING SO WILL RESULT IN EXCESSIVELY HIGH PRESSURE WITHIN
THE INFLATION CHAMBER, WHICH MAY CAUSE PERMANENT DAMAGE.
Fig. 10

10 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
SPECIAL CONSIDERATIONS FOR AUTOMATIC DEVICES (MD2953)
The Inflatable PFD might not be armed when needed, either
knowingly or unknowingly. Premature automatic inflation causes
several risks that you must address to avoid drowning. Much less
common but also important are:
1. Inflation when stored in a tight space could damage the PFD, and
2. The PFD could inflate when you are in an awkward place or
position.
3. Premature inflation may occur in certain conditions, including
when the device is subjected to: heavy splashing, high humidity,
heavy fog, and heavy rain.
4. Care and attention should be taken to ensure that when the
device is used in these types of conditions, auto-inflation does not
occur prematurely.
5. If this PFD should inflate prematurely, a re-arm kit (MA7114) is
required to re-arm the device.
IMPORTANT: THE INFLATABLE PFD SHOULD BE RE-ARMED ACCORDING TO THE
INSTRUCTIONS (SEE RE-ARMING YOUR PFD (MD2953), P.14).

11
DEFLATING THE INFLATABLE PFD
1. To deflate the Inflatable PFD, reverse the oral-inflation tube dust
cap and insert it into the valve. The dust cap will not lock in the
deflate position so it is necessary to hold it in place (Fig. 11). Do
not use your finger to depress the oral tube to expel air from the
bladder.
2. Gently squeeze the Inflatable PFD until all air or gas has been
expelled. To avoid damage; do not wring or twist the Inflatable
PFD. Put the inflation tube dust cap back in its stowed position on
the oral inflation tube (Fig. 12).
3. Examine the service indicator (Figs. 1 and 2). If the service
indicator is red, the mechanism has been fired or is incorrectly
fitted and the inflator requires service (see Re-arming your PFD
(for your model)).
NOTE: THE SERVICE INDICATOR MUST BE GREEN BEFORE PROCEEDING.
4. Your device is ready to be repacked (see "Repacking" on
p.17).
Cap in
Deflate
Position
Oral Inflator
Dust cap
in stowed
position
Dust cap
in position for
deflation
Fig. 11
Cap in
Deflate
Position
Oral Inflator
Dust cap
in stowed
position
Dust cap
in position for
deflation
Fig. 12

12 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
RE-ARMING YOUR MANUAL PFD (MD2951)
NOTE: A RE-ARM KIT (MA7114) IS REQUIRED FOR THIS PROCEDURE.
IMPORTANT: FOLLOW INSTRUCTIONS IN THE EXACT SEQUENCE BELOW.
1. Unpack or open the Inflatable PFD so that the inflator is exposed
(Fig. 13).
2. Remove the cylinder/bayonet assembly by rotating counter-
clockwise and then pull out. Discard the used cylinder/bayonet
assembly.
3. Check the new cylinder/bayonet assembly to ensure the o-ring is
in place and the sensor ring is attached (Fig. 16). Ensure that the
CO2 cylinder has not been pierced (Fig. 16).
Service
Indicator
Step 5
Cylinder
Step 2
O-Ring
Step 3
Tab
Step 4
Sensor Ring
Step 3
Bayonet
Lever
MD2951 Manual Inflator
SERVICE INDICATOR:
If green, unit is operable
If red, stop and service unit
Fig. 13

13
4. Raise, and hold, the lever into the inflator housing. Install a new
cylinder/bayonet assembly by engaging bayonet tabs in housing,
pushing in then turning clockwise 1/8 turn to a full stop (Fig. 14).
WARNING: PFD WILL ONLY INFLATE IF CYLINDER IS TURNED TO A FULL STOP.
5. Examine the service indicator (Fig. 13) and ensure it is GREEN. If
the service indicator is red, the mechanism has been fired or is
incorrectly fitted and the inflator requires service. (See Re-arming
Your PFD (MD2951), p.12).
NOTE: THE SERVICE INDICATOR MUST BE GREEN BEFORE PROCEEDING.
6. Refold the Inflatable PFD in accordance with the Repacking
section (See Repacking, p.17).
7. Your inflatable PFD (MD2951) is now ready for manual use.
Tab
Piercing Pin
Cylinder
Lever
Service Indicator
MD2951 Manual Inflator
1/8 Turn
Fig. 14

14 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
RE-ARMING YOUR AUTOMATIC PFD (MD2953)
NOTE: A RE-ARM KIT (MA7114) WITH A VALID BOBBIN INSTALL-BY-DATE
(CHECK RE-ARM KIT PACKAGING) IS REQUIRED FOR THIS PROCEDURE.
IMPORTANT: FOLLOW INSTRUCTIONS IN THE EXACT SEQUENCE BELOW.
1. Unpack or open the Inflatable PFD so that the inflator is exposed
(Fig. 15).
2. Remove the cylinder/bayonet assembly by rotating counter-
clockwise and then pull out. Discard the used cylinder/bayonet
assembly.
NOTE: YOU WILL DAMAGE THE SENSOR RING IF THE BOBBIN AND CAP ARE NOT
INSTALLED PRIOR TO THE NEW CYLINDER/BAYONET ASSEMBLY.
3. Remove cap by turning counter-clockwise. (Fig. 15).
4. Remove bobbin from cap or housing unit. Discard bobbin.
HOUSING**
Step 4
MD2953 Automatic Inflator
SERVICE INDICATOR:
If green, unit is operable
If red, stop and service unit
Cap
Step 3
Yellow Bobbin
(white side up)
Step 4
Housing
Shoulder
Step 8
Service
Indicator
Step 11
Pull-Tab
Lever
Step 10
Pins
O-ring
Step 9
Tab
Step 10
Bayonet
Sensor Ring
Step 9
CO
Cylinder
Step 2
Cylinder/
Bayonet
Assembly
Step 2
Fig. 15

15
NOTE: THE YELLOW BOBBIN MAY REMAIN IN THE HOUSING OR IN THE CAP ASSEMBLY
WHEN YOU REMOVE THE CAP. THE BOBBIN MUST BE REMOVED PRIOR TO RE-ARMING.
5. Check the housing to be sure it is clear and dry. If necessary,
rinse the inflator with fresh water to remove dirt and salt. Let dry
before going to step 6.
6. Inspect the bobbin. If the bobbin has been fired or damaged,
replace it! To ensure the new bobbin is valid, it must have
been purchased within the last three (3) years. If the bobbin
purchase date is unknown, check the date printed on the bobbin
and replace if older than three (3) years (see "Re-arming Your
Automatic PFD (MD2953)" on p.14).
7. IMPORTANT! Bobbin (yellow) must be installed into the HOUSING
(**see figure 15), white side up, aligning the slots on the bobbin
with the ridges inside the threaded housing. The bobbin will slide
in easily if installed correctly.
8. Install cap by screwing clockwise until it meets the housing
shoulder.
9. Check the new cylinder/bayonet assembly to ensure the o-ring is
in place and the sensor ring is attached (Figs. 15 and 16). Ensure
that the CO2cylinder has not been pierced (Fig. 16).
IMPORTANT: YOU WILL DAMAGE THE SENSOR RING IF BOBBIN AND CAP ARE NOT
INSTALLED FIRST.
Solid
Cylinder
Top
Attached
Sensor
Ring
Pierced
Cylinder
Top
Broken
Sensor
Ring
Caution: Do not use the
cylinder/bayonet assembly
if either the o-ring or
sensor ring is broken,
missing, or damaged
Fig. 16

16 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
10. Raise, and hold,the lever into the inflator housing. The pull-cord
should be situated in the groove (Fig. 17). Install a new cylinder/
bayonet assembly by engaging bayonet tabs in housing, pushing
in then turning clockwise 1/8 turn to a full stop (Fig. 17).
WARNING: PFD WILL ONLY INFLATE IF CYLINDER IS TURNED TO A FULL STOP.
11. Examine the service indicator (Fig. 15) and ensure it is GREEN. If
the service indicator is red, the mechanism has been fired or is
incorrectly fitted and the inflator requires service. (see "Re-arming
Your Automatic PFD (MD2953)" on p.14).
NOTE: THE SERVICE INDICATOR MUST BE GREEN BEFORE PROCEEDING.
12. Refold the Inflatable PFD in accordance with the Repacking
section (See Repacking, p.17).
Your inflatable PFD (MD2953) is now ready for manual use with
automatic backup.
Service
Indicator
Groove
Pull-cord
Tab
Piercing
Pin
Cylinder
MD2953 Automatic Inflator
1/8 Turn
Fig. 17

17
REPACKING
Gently squeeze the Inflatable PFD until all air or gas has been
expelled (Fig. 11). Do not wring or twist the Inflatable PFD. Put the
inflation tube dust cap back in its stowed position on the oral inflation
tube (Fig. 12). Do not use finger to depress oral tube to expel air from
bladder.
NOTE: BEFORE FOLLOWING THE REPACKING SEQUENCE, BE SURE TO PROPERLY
RE-ARM YOUR INFLATABLE PFD.
1. Work on a smooth surface free from any sharp objects which
could puncture or damage the unit.
2. Fold outer sides along the full length of the dotted line (Fig. 18).
3. Fold the two inner sides along dotted lines (Fig. 19). Fasten along
the full length of the Velcro™. Ensure that the Inflatable PFD is
tucked under the Velcro™ strip.
4. Turn the PFD over so the back of the PFD is facing you (Fig. 21).
5. Fold down the back flap and fasten the three Velcro strips in
the back panel together, ensuring the bladder fabric is securely
tucked inside (Fig. 21).
6. Fig. 22 shows back view of a correctly folded inflatable PFD.
7. Ensure the pull-tab is on the outside of the folded Inflatable PFD
by pulling it through an elastic loop at the bottom. Be careful
not to pull too hard as it could cause accidental inflation.
8. Fig. 23 depicts a correctly folded Inflatable PFD.
NOTE: ENSURE THAT ALL VELCRO™ STRIPS AND TABS ARE FASTENED.
Fig. 18 Fig. 19

18 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
Fig. 20
Fig. 22
Fig. 21
Fig. 23

19
IS YOUR PFD IN GOOD AND SERVICEABLE CONDITION?
Check your Inflatable PFD between outings to be sure that it is
properly armed; that it is free of rips, tears or holes; that all seams are
securely sewn; and that the fabric, straps and hardware are still strong
(see "Readiness Checklist" on p.6). Inspect the inflatable portion
of the Inflatable PFD in accordance with the Care and Maintenance
instructions.
USAGE BELOW FREEZING [0OC / 32OF]
If you choose to use your PFD below freezing, performance will not
be as expected. Below freezing, a discharged cylinder may not fully
inflate your PFD to the intended pressure. You will need to rely on
your back up oral inflation system to adjust the internal pressure
to achieve adequate buoyancy (see Oral Inflation, p.9).
CARE AND MAINTENANCE INSTRUCTIONS
It is important to care for and maintain your inflatable PFD in order
to ensure it will perform as designed when you need it. Be sure to
keep a record of the inspections performed on your PFD. If you are
not confident in the self-inspection and servicing of your inflatable
PFD in accordance with these instructions, contact Mustang Survival
customer service.
INSPECTING YOUR INFLATABLE PFD
Before Each Use:
Examine the single point status indicator ensuring it is green.
If the indicator is red, your PFD needs to be re-armed
(See Re-arming Your PFD, (for your model)).
Ensure the manual pull-tab is properly stowed.
Visually examine your inflatable PFD for damage or excessive
abrasion, wear, tear and/or contamination. If any item shows
signs of damage, perform tasks listed in "Every Six (6)
Months" inspection details.

20 MUSTANG SURVIVAL/ OWNER'S MANUAL – DLX 38 INFLATABLE PFD
Every Six (6) Months:
In addition to the inspections specified for before each use, perform
the following at least every 6 months, or more often if exposed to
potential damage or used in extreme conditions.
Leak Test: Your Inflatable PFD should be tested for leakage by
inflating with air until firm and leaving it to stand for at least
2 hours in a temperature controlled environment. A leaking
Inflatable PFD will not remain firm and should be replaced. If
your Inflatable PFD leaks, contact Mustang Survival
customer service.
Annually:
In addition to the inspections specified for every six months, perform
the following at the beginning of each boating season or whenever
the integrity of your inflatable PFD is in doubt:
Thoroughly check all components for dirt and/or corrosion.
Clean or replace, as necessary. If any item shows signs of
damage, perform inspections listed in "Every Six (6) Months"
inspection details. If in doubt, contact Mustang Survival
customer service.
For MD2953 only. Ensure the current date is not three (3)
years past the date on the bobbin. If it is, re-arm the inflator
(See Re-arming Your PFD, p.14).
CLEANING AND STORING YOUR PFD
To clean your inflatable PFD, hand wash or sponge down in warm,
soapy water, taking care not to get the inflator wet. Rinse your PFD
with clean water, and hang to dry on a plastic coat hanger. Do not
dry-clean, use chlorine bleach, or apply direct heat. Always store
your fully dried PFD in a warm, dry, well ventilated place out of direct
sunlight.