Aetertek AT-216 User manual

R
www.aetertek.com
AT-216
User's Manual for Dog training colla AT-216

Additional Information for Terms of Use and Limitation of Liability
1. Terms of
Use
This product is offered to you conditioned upon your acceptance without modification of the
terms, conditions, notices contained herein. Usage of this product implies acceptance of all such
terms, conditions, and notices.
2. Proper
Use
This product is designed for use with dogs where training is desired. The specific temperament of
your dog may not work with this product. We recommend that you not use this product if your dog
is less than 8 pounds or if your dog is aggressive. If you are unsure whether this is appropriate for
your dog, please consult your veterinarian, certified trainer or contact our customer support.
3. No Unlawful or Prohibited Use
This product is designed for use with dogs only. This dog training device is not intended to harm,
injure, or provoke. Using this product in a way that is not intended could result in violation of
Federal, State or local laws.
4.Limitation of Liability
In no event shall Aetertek be liable for any direct, indirect, punitive, incidental, special or
consequential damages, or any damages whatsoever arising out of or connected with the use or
misuse of this product. Buyer assumes all risks and liability from the use of this product.
5. Modification of Terms and Conditions
Aetertek reserves the right to change the terms, conditions, and notices under which this product is
offered.
For parts and warranty, contact with authorized dealer shown in warranty card

Hardware Included------------------------------------------------------------------------02
Quick Start --------------------------------------------------------------------------------03-04
Training Tips ------------------------------------------------------------------------------05-06
Safety --------------------------------------------------------------------------------------07
Common Problems & Fixes-------------------------------------------------------------08-09
Safety Guidance---------------------------------------------------------------------------10
Warranty , Terms & Conditions , compliance------------------------------------------11-12
Additional Information for Terms of Use and Limitation of Liability------------------13
-01-

R
Super Remote Dog Trainer
AT-216
AT-216 AT-216
-02-

Quick Start
R
Super Remote Dog Trainer
1
Step 1 Install the antenna onto the transmitter. Make sure the
antenna is securely attached.
4
Step 4 Charge the receivers.
A RED LED light of the receiver is on during charging. When
charging is over, the red LED light will be off with the
BLUE LED light on. Full battery charge takes about 3 hours.
Tips: Recommend to charge the receiver upto 4 hours
for the first 3 times .
2
Step 2 Install the 9V battery into the transmitter correctly .
(Note: pay attention to the positive and negative poles )
a:Press and hold
on On/Off
button until the
red LED light to
be solid.
Note:if receiver just
charg ed, the red LED
light is solid and receiver
is waiting for sync, so no
need to do this
Step 5: Sync the receiver and transmitter.
b:press down Shock,
Beep or Vibrate button,
receiver will get to be
communicated
with transmitter.
5
3
Step 3: Screw the metal prongs onto the receiver till securely attached.
a: Unplug the charger, the red Led light is solid and receiver
is waiting for sync ;
Note:if receiver had been turned off and still have power
remained,press and hold on the On/Off button until the red Led
light to be solid, then the receiver is waiting for sync. b :push
any of the function buttons
(shock, beep, vibrate) on the transmitter. As soon as the
receiver pairs with the transmitter, the RED LED light turns
off and BLUE LED light flashes every 10 seconds. -03-

Quick Start
6
Step 6: Check the Function buttons (beep, vibrate, shock)
Push the Beep button or Vibrate button, the receiver will produce
beeping sound or vibration. To test the shocks, cap the shock test
kit on the metal prongs, push the shock button to see the bulb
light up immediately.
0 7
8
Step 8 Choose the dog mode(Dog1, or Dog2, or Dog3)
Push the Dog Switch button in the left of the transmitter to
choose a dog mode(Dog1,Dog2,Dog3). Push the button to
change dog mode from Dog1-Dog2-Dog3 . Dog 1 means the
first dog, Dog2 is for the second dog, Dog3 is for the second
dog . If you need to train the 3 dogs separately, please pair
the transmitter and receiver one by one
7
0
7
Step 7 Adjust the intensity or duration of the functions
Rotate the thumbwheel dial to choose the desired levels
of correctional signals.
Note : Longer(shorter) holding beep, vibrate or shock button will
lead to longer (shorter) duration of beep, vibrate or shock time.
Start to train:
Put the collar into the receiver, wear the receiver around dog ’s neck, leave one finger place between the collar and the neck, then it ’s
-04-
ready to train.

Super Remote Dog Trainer
R
-05-

R
Super Remote Dog Trainer
Aetertek
-06-

AT-216
R
Super Remote Dog Trainer
-07-

R
Super Remote Dog Trainer
No beep, vibration or shock
-08-

R
Super Remote Dog Trainer
-09-

R
Super Remote Dog Trainer
Aetertek AT-216
-10-

R
Super Remote Dog Trainer
Aetertek
-11-

R
Super Remote Dog Trainer
-12-
Warranty, Terms & Conditions,
Compliance(continued)
Aetertek

Additional Information for Terms of Use and Limitation of
Liability
R
Super Remote Dog Trainer
1. Terms of Use
This product is offered to you conditioned upon your acceptance without modification of the
terms, conditions, notices contained herein. Usage of this product implies acceptance of all such
terms, conditions, and notices.
2. Proper Use
This product is designed for use with dogs where training is desired. The specific temperament of
your dog may not work with this product. We recommend that you not use this product if your dog
is less than 8 pounds or if your dog is aggressive. If you are unsure whether this is appropriate for
your dog, please consult your veterinarian, certified trainer or contact our customer support.
3. No Unlawful or Prohibited Use
This product is designed for use with dogs only. This dog training device is not intended to harm,
injure, or provoke. Using this product in a way that is not intended could result in violation of
Federal, State or local laws.
4.Limitation of Liability
In no event shall Aetertek be liable for any direct, indirect, punitive, incidental, special or
consequential damages, or any damages whatsoever arising out of or connected with the use or
misuse of this product. Buyer assumes all risks and liability from the use of this product.
5. Modification of Terms and Conditions
Aetertek reserves the right to change the terms, conditions, and notices under which this product is
-13-

This equipment has been tested and found to comply with the limits for a Class B digital device, pur
suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate ra
dio frequency energy and, if not installed and used in accordance with the instructions, may cause h
armful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or te
levision reception, which can be determined by turning the equipment off and on, the user is encour
aged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is conne
cted.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.