Aewin AW-EM730 User manual

AEWIN Technology Inc.
We embed your need! ©Copyright 2006
3.5” Embedded SBC
Model Number AW-EM730
Intel® Pentium® M Embedded SBC with LVDS, LAN, Audio & SSD
User’s Manual
Version 1.3

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 2Ver 1.3 Mar, 2006
© Copyright 2006. All Rights Reserved
Manual Edition 1.3, Mar 2006
This document contains proprietary information protected by copyright. All rights
are reserved; no part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without prior written permission of the
manufacturer.
The content of this manual is intended to be accurate and reliable; the original
manufacturer assumes no responsibility for any inaccuracies that may be contained
in this manual. The original manufacturer reserves the right to make improvements
to the products described in this manual at any time without prior notice.
Trademarks
IBM, EGA, VGA, XT/AT, OS/2 and PS/2 are registered trademarks of International
business Machine Corporation
Award is a trademark of Award Software International, Inc
Intel is a trademark of Intel
RTL is a trademark of Realtek
VIA is a trademark of VIATechnologies, Inc
Microsoft, Windows, Windows NT and MS-DOS are either trademarks or registered
trademarks of Microsoft Corporation
All other product names mentioned herein are used for identification purpose only
and may be trademarks and/or registered trademarks of their respective companies
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual, the
manufacturer and distributor assume no liability resulting from errors or omissions in
this manual, or from the use of the information contained herein.

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 3Ver 1.3 Mar, 2006
Table of Contents
Chapter 1. General Information ......................................................................................... 4
1.1 Introduction............................................................................................................... 4
1.2 Specification ............................................................................................................. 4
1.3 Package.....................................................................................................................5
1.4 Precautions................................................................................................................ 6
1.5 Board Layout ............................................................................................................ 7
1.6 Board Dimension...................................................................................................... 8
Chapter 2. Connector/Switch Location and Configuration............................................. 9
2.1 Connector/Jumper Location and Definition.............................................................. 9
2.2 Install Memory........................................................................................................ 11
2.3 Connector and Jumper Setting................................................................................ 13
Chapter 3. BIOS Setup...................................................................................................... 28
3.1 Quick Setup............................................................................................................. 28
3.2 Entering the CMOS Setup Program........................................................................ 29
3.3 Menu Options.......................................................................................................... 30
3.4 Standard CMOS Features Setup ............................................................................. 31
3.5 Advanced BIOS Features Setup.............................................................................. 32
3.6 Advanced Chipset Features Setup........................................................................... 34
3.7 Integrated Peripherals ............................................................................................. 35
3.8 Power Management Setup ...................................................................................... 38
3.9 PNP/PCI Configuration .......................................................................................... 41
3.10 PC Health Status Configuration Setup.................................................................. 43
3.11 Load Fail-Safe Defaults ........................................................................................ 43
3.12 Load Optimized Defaults...................................................................................... 44
3.13 Supervisor/User Password .................................................................................... 45
3.14 Save and Exit Setup.............................................................................................. 46
3.15 Exit Without Saving.............................................................................................. 46
Chapter 4. Software & Driver Utility................................................................................. 47
4.1 Operation System Installation................................................................................. 47
4.2 Device Driver Installation....................................................................................... 47
4.2.1. Intel 82562ET Ethernet................................................................................. 47
4.2.2. CRT and LVDS Driver.................................................................................. 48
Appendix A: Optional Module........................................................................................... 49
1. AC97 Audio Kit (SPK Out, MIC In) ........................................................................ 49
2. +12~24V Power adapter Kit..................................................................................... 51
Appendix B: Optional Cable List...................................................................................... 54

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 4Ver 1.3 Mar, 2006
Chapter 1. General Information
1.1 Introduction
The AW-EM730 3.5” embedded board is based on Intel® architecture with
852GM+ICH4 chipset supporting the Pentium® M Celeron M processor with
400MHz FSB. The memory supports DDR SO-DIMM socket up to 1GB. Through
Intel® 82562ET chipset, it can support one Ethernet port. The built-in 852GM
chipset supports CRT and LVDS panel interface.
Other features include a CompactFlash socket, one mini PCI slot for future
expansion capabilities, four USB2.0 ports, three RS-232 and one RS-232/485 Serial
port, one Parallel port, AC97 audio, watchdog timer and hardware system
monitoring, etc.
1.2 Specification
General Functions
CPU Intel® Celeron® M ULV 600MHz Zero cache processor
BIOS Award® 512KB Flash BIOS
Cache Non on-chip cache
Chipset Intel® 852GM + ICH4
I/O Chipset Winbond® 83627HF-AW
Memory Onboard one DDR SO-DIMM socket can support up to 1GB
Enhanced IDE One 44-pin IDE connector supports Ultra DMA33/66/100 mode
Serial port Three RS-232 and one RS-232/485（4wire/2wire）serial ports
KB/Mouse
connector Supports PS/2 keyboard and mouse
Parallel port Pin header for bi-directional parallel port, supports SPP, ECP and EPP
mode
USB connectors Support four USB2.0/1.1 ports
Battery Lithium battery
Watchdog timer Can generate a system reset, support software selectable timeout
interval
System Built in W83627HF-AW; support temperatures, voltage monitoring

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 5Ver 1.3 Mar, 2006
Monitoring function
PCI expansion One Mini PCI expansion slot
Flat Panel/CRT Interface
Chipset Built-in 852GM chipset
Display type Support CRT and LVDS panel interface
Ethernet Interface
Chipset One Intel 82562ET 10/100Mbps Ethernet controller
Audio Interface (Optional Audio Module)
Chipset Analog Device AD1881 AC97 CODEC
Audio interface Support Mic in, Speaker out
SSD interface One 50-pin CompactFlashTM socket
Mechanical and Environmental
Power supply voltage Single +5V power supply
Operating temperature 32 to 140℉（0 to 60℃）
Board size 5.7”(L) x 4”(W) (145mm x 102mm)
1.3 Package
Please make sure that the following items have been included in the
package before installation.
1. AW-EM730 Embedded SBC
2. Quick Installation Guide
3. Cable: Please refer to Appendix B “Standard Cables”
4. CD-ROM that contains the following folders:
(1) Manual
(2) System Driver
(3) Ethernet Driver
(4) Utility Tools
If any item of above is missing or damaged, please contact your dealer
or retailer from whom you purchased the AW-EM730. Keep the box and
carton when you probably ship or store AW-EM730 in near future. After
you unpack the goods, inspect and make sure the packaging is intact.
Do not plug the power adapter to the main board of AW-EM730 if you
already find it appears damaged.
Note: Keep the AW-EM730 in the original packaging until you start installation.

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 6Ver 1.3 Mar, 2006
1.4 Precautions
Please make sure you properly ground yourself before handling the AW-EM730
board or other system components. Electrostatic discharge can be easily damage
the AW-EM730 board.
Do not remove the anti-static packing until you are ready to install the AW-EM730
board.
Ground yourself before removing any system component from it protective
anti-static packaging. To ground yourself, grasp the expansion slot covers or other
unpainted parts of the computer chassis.
Handle the AW-EM730 board by its edges and avoid touching the components on it.

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 7Ver 1.3 Mar, 2006
1.5 Board Layout
(Rear View)
(Front View)
AW-R031
(Audio Kit) AW-R041 (PowerAdapter Kit)

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 8Ver 1.3 Mar, 2006
1.6 Board Dimension
(Front View)
(Rear View)

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 9Ver 1.3 Mar, 2006
Chapter 2. Connector/Switch Location and Configuration
2.1 Connector/Jumper Location and Definition

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 10 Ver 1.3. Mar, 2006
List of Connectors
Connectors Description Connectors Description
CN1 VGA Connector (D-Sub) CN13
CN2 COM1 Connector (D-Sub) CN14 LVDS Connector
CN3 +12V Input CN15 AC97 Connector
CN4 Mini Din CN16 Mini PCI Socket
CN5 CN17 COM2 Pin-Header
CN6 Front Panel Connector CN18 Power Connector
CN7 Inverter Connector CN19 COM3/4 Pin-Header
CN8 USB Connector CN20 IDE Connector
CN9 +5V Fan Connector CN21 LPT Pin-Header
CN10 LAN Connector (RJ45) CN22 Compact Flash Socket
CN11 USB Pin-Header CN23 DDR SO-DIMM
CN12
List of Jumpers
Jumper Description
JP1 Power On/Off Control
JP3 Power Selection for Inverter
JP4 LCD Panel Power Selection
JP5 CMOS Jumper
JP7 RS232/485 Jumper
JP8 RS485 Terminal Jumper
VR1 Adjust the brightness of backlight
JP1 JP3 JP4JP5
JP8JP7

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 11 Ver 1.3. Mar, 2006
2.2 Install Memory
To insert a DIMM Memory:
The AW-EM730 supports one SO-DIMM DDR socket, memory up to 1GB. Please make
sure to insert DDR with registered.
To Insert a DIMM Memory: Please align the module with the socket key and press down
until the levers at each end of the socket snap close up.
There is only one direction for installing a module in the socket. Do not attempt to force the
module into the socket incorrectly.

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 12 Ver 1.3. Mar, 2006
To Remove a DIMM Memory: To remove a DIMM, press down on the levers at both end of
the module until the module pops out

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 13 Ver 1.3. Mar, 2006
2.3 Connector and Jumper Setting
CN1: VGA Connector
The AW-EM730 supports a standard D-SUB VGAconnector for CRT display.
Pin Signal
1 RED
2 GREEN
3 BLUE
4 NC
5 Ground
6 Ground
7 Ground
8 Ground
9 NC
10 Ground
11 NC
12 DDC Data
13 H-SYNC
14 V-SYNC
15 DDC Clock
CN2, CN17, CN19: Serial Ports
The AW-EM730 supports four serial ports: three RS-232 (COM1/COM3/COM4) and one
RS-232/422/485 (COM2). The COM1(CN2) is D-Sub connector and COM2/COM3/COM4 are pin
header type. These ports allow user to connect serial devices such as mouse, keyboard or others. It
needs the additional adapter cables to use the traditional DB-9 connector for COM2/COM3/COM4.
The cable for COM2 is 14-pin, and the cable for COM3/COM4 is 10-pin.
The COM2 is designed to be the RS232 port; also it can be compliant with the RS-422/485
interface in the JP7.
CN1

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 14 Ver 1.3. Mar, 2006
CN2: COM1 D-Sub Connector
Pin Signal
1 DCD
2 RXD
3 TXD
4 DTR
5 Ground
6 DSR
7 RTS
8 CTS
9 RI
CN3: +12V input Connector
The AW-EM730 can support +12V power input. If +12V power is needed, we offer AW-R029 that
is a +12V DC to +5V DC adapter. Please install & assemble the adapter, then connect the CN5 in
AW-R029 to the AW-EM730 CN3.
Pin Signal
1 +12V input
2 GND
CN3
Note: If the backlight inverter CN7 and JP3 select
+12V power input, then the CN3 must be shorted
and connected toAW-R029.
CN2

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 15 Ver 1.3. Mar, 2006
CN4: PS/2 Mouse/Keyboard Connector (MINI DIN Jack)
The AW-EM730 can support MINI DIN jack for PS/2 mouse or keyboard use.
CN6: Front Panel
Pin Signal Pin Signal
1 Power LED+ (+5V) 2 Power LED- (GND)
3 IDE_LED+ (+5V) 4 IDE_LED- (ACTIVE)
5 POWER ON SWITCH+ 6 POWER ON SWITCH (GND)
7 RESET SWITCH+ 8 RESET SWITCH- (GND)
Pin 1-2: the two pins connect to the case-mounted power LED.
Pin 3-4: the two pins connect to the case-mounted HDD LED & indicate HDD active.
Pin 5-6: the two pins connect to case-mounted ATX power button.
Pin 7-8: the two pins connect to case-mounted reset switch for reboot function.
Pin Signal
1 KB-DATA
2 MS-DATA
3 Ground
4 +5V
5 KB-CLK
6 MS-CLK
CN4
82
71
CN6

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 16 Ver 1.3. Mar, 2006
CN7: Inverter Connector
The AW-EM730 can provide the power +12V or +5V for backlight inverter and brightness control
through the inverter connector CN7.
Note:
1. The power input (+12V or +5V) selection depends on the JP3, please refer to the JP3
setting to get more information.
2. To change the brightness, please adjust the VR1 on the AW-EM730 board.
Pin Signal
1 +12V/+5V
2 +12V/+5V
3 Ground
4 Ground
5 Backlight Enable
6 Brightness
CN7

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 17 Ver 1.3. Mar, 2006
CN8: USB2.0 Connector
The AW-EM730 is equipped with two USB 2.0 (Universal Serial Bus) ports, which can support
plug and play, hot attach/detach functions. It also can be backward compliant with USB 1.1
interface.
CN9: +5V Fan Connector
Pin Signal
1 5VUSB0
2 USBDT0-
3 USBDT0+
4 Ground
5 5VUSB0
6 USBDT1-
7 USBDT1+
8 Ground
Pin Signal
1 +5V
2 GND-
CN8
2 1
CN9

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 18 Ver 1.3. Mar, 2006
CN10: RJ45 Connector
The AW-EM730 is equipped with one RJ-45 connector. It can let the device to support 10Mbps
and 100Mbps Ethernet.
Pin Signal
1 TX0+
2 TX0-
3 RX0+
4 NC
5 NC
6 RX0-
7 NC
8 NC
CN11: USB2.0 Pin-Header
AW-EM730 is equipped with USB2.0 pin header; it can support two more USB2.0 devices.
Pin Signal Pin Signal
1 USBVCC(+5V) 2 USBVCC(+5V)
3 USB2- 4 USB3-
5 USB2+ 6 USB3+
7 GND 8 GND
9 KEY-Pin 10 GND
CN10
1 2
10
CN11

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 19 Ver 1.3. Mar, 2006
CN14: LVDS Connector
The AW-EM730 supports LVDS output via a 20 pin connector for LVDS panel.
Pin Signal Pin Signal
1 VCC3/VCC5 2 VCC3/VCC5
3 GND 4 GND
5 RxIN0- 6 RxIN0+
7 GND 8 RxIN1+
9 RxIN1- 10 GND
11 RxIN2- 12 RxIN2+
13 GND 14 CLKIN-
15 CLKIN+ 16 GND
17 RxIN3- 18 RxIN3+
19 DDCPDATA 20 DDCPCLK
CN15: AC97 Connector
This AW-EM730 supports AC97 function, the connector is designed as 12 pin for CD Audio cable
that depends on the CD-ROM drive type.
Pin Signal Pin Signal
1 +5V 2 GND
3 GND 4 AC97_BITCLK
5 +3.3V 6 KEY pin
7 AC97_SDIN 8 AC97_SYNC
9 GND 10 AC97_ACRST
11 AC97_SDOUT 12 NC
1
7
9
3
10
4
8
5
11
2
CN15
Note: The AC97 function needs to equip with the AW-R031
module. Please refer to Appendix A the see the detail.
CN14

User’s Manual
©2006 AEWIN Technologies Co., Ltd. All rights reserved. 20 Ver 1.3. Mar, 2006
CN16: Mini PCI slot
Pin Define Pin Define
1 TIP 2 RING
3 8PMJ-33 4 8PMJ-13
5 8PMJ-63 6 8PMJ-23
7 8PMJ-73 8 8PMJ-43
9 8PMJ-83 10 8PMJ-53
11 LED1_GRNP 12 LED2_YELP
13 LED1_GRNN 14 LED2_YELN
15 CHSGND 16 RESERVED
17 INTB/D# 18 5V
19 3.3V 20 INTA/C#
21 RESERVED 22 RESERVED
23 GND 24 3.3VAUX
25 CLK 26 RST#
27 GND 28 3.3V
29 REQ# 30 GNT#
31 3.3V 32 GND
33 AD{31} 34 PME#
35 AD{29} 36 RESERVED
37 GND 38 AD{30}
39 AD{27} 40 3.3V
41 AD{25} 42 AD{28}
43 RESERVED 44 AD{26}
45 C/BE[3]# 46 AD{24}
47 AD{23} 48 IDSEL
49 GND 50 GND
51 AD{21} 52 AD{22}
53 AD{19} 54 AS{20}
55 GND 56 PAR
57 AD{17} 58 AD{18}
59 C/BE[2]# 60 AD[16]
61 IRDY# 62 GND
63 3.3V 64 FRAME#
65 CLKRUN# 66 TRDY#
67 SERP# 68 STOP#
69 GND 70 3.3V
71 PERP 72 DEVSEL#
73 CB/E[1] 74 GND
75 AD[14] 76 AD[15]
77 GND 78 AD[13]
79 AD[12] 80 AD[11]
81 AD[10] 82 GND
83 GND 84 AD[09]
85 AD[06] 86 C/BE[0]#
87 AD[07] 88 3.3V
89 3.3V 90 AD[06]
91 AD[05] 92 AD[04]
93 RESERVED 94 AD[02]
95 AD[03] 96 AD[00]
97 5V 98 RESERVED_
WIP4
99 AD[01] 100 RESERVED_
WIP4
101 GND 102 GND
103 AC_SYNC 104 M66EN
105 AC_SDATA_IN 106 AC_SDATA_
OUT
107 AC_BIT_CLK 108 AC_CODEC_
CN16