AG Neovo DR-17G User manual

DR-17G & DR-22G LCD Monitor
User Manual
displays.agneovo.com

TABLE OF CONTENTS
2
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)............................................................4
WEEE.......................................................................................................................................................5
EMC Information ......................................................................................................................................6
Precautions
Notice.......................................................................................................................................................10
Cautions When Setting Up.......................................................................................................................11
Cautions When Using...............................................................................................................................12
Cleaning and Maintenance.......................................................................................................................13
Notice for the LCD Display.......................................................................................................................13
Chapter 1: Product Description
1.1 Packa ge Contents..............................................................................................................................15
1.2 Wall Mounting Installation Preparation...............................................................................................16
1.2.1 Wall Mounting..........................................................................................................................16
1.2.2 Removing the Base Stand.......................................................................................................17
1.3 LCD Display Overview .......................................................................................................................18
1.3.1 Front View and Keypad Buttons..............................................................................................18
1.3.2 Rear View................................................................................................................................20
Chapter 2: Making Connections
2.1 Connecting the Power........................................................................................................................21
2.2 Connecting Input Source Signals.......................................................................................................22
2.2.1 Connecting a Computer ..........................................................................................................22
Using VGA Cables ......................................................................................................................... 22
Using DVI Cables...........................................................................................................................22
Using HDMI Cables........................................................................................................................23
Using DisplayPort Cables ..............................................................................................................23
Using RS232 Cables......................................................................................................................24
Using Audio Cables........................................................................................................................24
2.2.2 Connecting a Video Device.....................................................................................................25
Using Composite (CVBS) Cables ..................................................................................................25
Using S-Video Cables....................................................................................................................26
Using HDMI Cables........................................................................................................................26
Using DisplayPort Cables ..............................................................................................................27
Chapter 3: Using the LCD Display
3.1 Turning on the Power.........................................................................................................................28
3.2 Selecting the Input Source Signal......................................................................................................28
3.3 Adjusting the Volume / Illuminator Function Hot Key..........................................................................29
3.3.1 Muting the Audio......................................................................................................................29
3.3.2 Illuminator Function Hot Key...................................................................................................29
3.4 Choosing Your Preferred Picture Settings..........................................................................................29
3.5 Using Picture-in-Picture (PIP) ............................................................................................................30
3.5.1 PIP/PBP Options.....................................................................................................................30
3.5.2 PIP/PBP Swap ........................................................................................................................31

3
TABLE OF CONTENTS
3.6 Using FREEZE Function....................................................................................................................31
3.7 Using Auto Adjustment Function ........................................................................................................32
3.8 Using ROTATE Function ....................................................................................................................32
3.9 Locki ng the OSD Menu......................................................................................................................33
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu .........................................................................................................................34
4.2 OSD Menu Tree .................................................................................................................................36
Chapter 5: Adjusting the LCD Display
5.1 Brightness ..........................................................................................................................................39
5.2 Colour Temp.......................................................................................................................................41
5.3 Image Setting.....................................................................................................................................42
5.4 Aspect Ratio.......................................................................................................................................45
5.5 PIP Setting .........................................................................................................................................46
5.6 Anti-Burn-in.........................................................................................................................................48
5.7 OSD Setting .......................................................................................................................................49
5.8 Audio Setting......................................................................................................................................50
5.9 System 1 ............................................................................................................................................51
5.10 System 2 ..........................................................................................................................................53
5.11 EcoSmart Sensor .............................................................................................................................54
5.12 Input Select ......................................................................................................................................56
Chapter 6: Appendix
6.1 Warning Messages.............................................................................................................................57
6.2 Supported Resolutions.......................................................................................................................58
6.3 Troubleshooting..................................................................................................................................59
6.4 Transporting the LCD Display ............................................................................................................61
Chapter 7: Specications
7.1 Display pecications ........................................................................................................................62
7.2 Display Dimensions............................................................................................................................63
7.2.1 DR-17G Dimensions ...............................................................................................................63
7.2.2 DR-22G Dimensions ...............................................................................................................63

SAFETY INFORMATION
4
Safety Information
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer
device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive
moisture.
THIS CLASS B DIGITALAPPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

5
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.
Standard Test item Standard
EN60601-1-2:2007
RAD & CON EN55011(EMI)
Harmonic EN61000-3-2
Flicker EN61000-3-3
ESD IEC 61000-4-2
RS IEC 61000-4-3
EFT IEC 61000-4-4
Surge IEC 61000-4-5
CS IEC 61000-4-6
PFM IEC 61000-4-8
DIP IEC 61000-4-11

6
SAFETY INFORMATION
EMC Information
CAUTION
The DR-17G and DR-22G requires special precautions regarding EMC and need to be installed, put into
service and used according to the following information.
Do not use any cables other than the cables that provided or specied by us. Using other cables may cause
the increase of emission or decrease of immunity.
Do not put any portable and mobile RF communications equipment close to the DR-17G and DR-22G. Doing
so may affect the DR-17G and DR-22G.
The DR-17G and DR-22G should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary, the equipment or system should be observed to verify normal operation in the
conguration in which it will be used.
Anyone who connects additional equipment to the signal input part or signal output parts, conguring a
medical system, responsible that the system complies with the requirements of IEC/ EN60601-1-2.
Guidance and manufacturer’s declaration – electromagnetic emissions
The DR-17G and DR-22G is intended for use in the electromagnetic environment specied below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Emissions test Compliance Electromagnetic environment – guidance
RF emissions
CISPR11/EN55011 Group 1
The DR-17G and DR-22G uses RF energy only for its
internal function. Therefore, its RF emission are very
low and are not likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR11/EN55011 Class B The DR-17G and DR-22G is suitable for use in all
establishments, including domestic establishments
and those directly connected to the public low-voltage
power supply network that supplies buildings used for
domestic purposes.
Harmonic emissions
IEC/EN61000-3-2 Class A
Voltage uctuations /
icker emissions
IEC/EN61000-3-3 Class A

7
SAFETY INFORMATION
Guidance and manufacturer’s declaration – electromagnetic immunity
The DR-17G and DR-22G is intended for use in the electromagnetic environment specied below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Immunity test IEC/EN60601
test level Compliance level Electromagnetic environment – guidance
Electrostatic
discharge (ESD)
IEC/EN61000-4-2
±8 kV contact
±15 kV air
±8 kV contact
±15 kV air
Floors should be wood, concrete
or ceramic tile. If oors are covered
with synthetic material, the relative
humidity should be at least 30%.
Electrical fast
transient / burst
IEC/EN61000-4-4
±2 kV for power supply
lines
±1 kV for input/output
lines
±2 kV for power supply
lines
±1 kV for input/output
lines
Mains power quality should be that
of a typical commercial or hospital
environment.
Surge
IEC/EN61000-4-5
For power supply lines:
± 1 kV line(s) to line(s)
± 2 kV line(s) to earth
For outdoor signal lines:
± 2 kV line(s) to earth
For power supply lines:
± 1 kV line(s) to line(s)
± 2 kV line(s) to earth
For outdoor signal lines:
± 2 kV line(s) to earth
Mains power quality should be that
of a typical commercial or hospital
environment.
Voltage dips, short
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
0% UT; 0,5 cycle
0% UT; 1 cycle
70% UT; 25/30 cycles
<5% UT; 250/300 cycles
0% UT; 0,5 cycle
0% UT; 1 cycle
70% UT; 25/30 cycles
<5% UT; 250/300 cycles
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of the
DR-17G and DR-22G requires
continued operation during
power mains interruptions, it is
recommended that the DR-17G
and DR-22G be powered from an
uninterruptible power supply or a
battery.
Power frequency
(50/60Hz)
magnetic eld
IEC/EN61000-4-8
3A/m 3A/m
Power frequency magnetic
elds should be at levels
characteristic of a typical location
in a typical commercial or hospital
environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Mains power quality should be that of a typical commercial or hospital environment. If the user of the DR-17G
and DR-22G requires continued operation during power mains interruptions, it is recommended that the
DR-17G and DR-22G be powered from an uninterruptible power supply or a battery.

8
SAFETY INFORMATION
Guidance and manufacturer’s declaration – electromagnetic immunity
The DR-17G and DR-22G is intended for use in the electromagnetic environment specied below. The
customer or the user of the DR-17G and DR-22G should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Immunity test IEC/EN60601
test level Compliance level Electromagnetic environment – guidance
Conducted RF
IEC/EN61000-4-6
Radiated RF
IEC/EN61000-4-3
3Vrms
150kHz to 80MHz
3V/m
80MHz to 2.5GHz
3Vrms 3V/m
Portable and mobile RF
communications equipment should
be used no closer to any part of the
DR-17G and DR-22G, including
cables, than the recommended
separation distance calculated
from the equation applicable to the
frequency of the transmitter.
Recommended Separation distance
d = 1.2 √ P d = 1.2 √ P, 80MHz to
800MHz
d = 2.3 √ P, 800MHz to 2.5GHz
Where “P”is the maximum output
power rating of the transmitter in
watts (W) according to the transmitter
manufacturer and “d” is the
recommended separation distance in
meters (m).
Field strengths from xed RF
transmitters, as determined by an
electromagnetic site survey:
a. should be less than the
compliance level in each
frequency range
b. Interference may occur in the
vicinity of equipment marked with
the following symbol
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and
land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to xed RF transmitters, an
electromagnetic site survey should be considered. If the measured eld strength in the location in which the
DR-17G and DR-22G is used exceeds the applicable RF compliance level above, the DR-17G and DR-22G
should be observed to verify normal operation. If abnormal performance is observed, additional measures
may be necessary, such as reorienting or relocating the DR-17G and DR-22G.

9
SAFETY INFORMATION
ESD declaration statement
There was ickered disturbance on the screen during the test, but could self-recover after the test.
(This permissive loss of performance was met the specication of EUT.)
DIP declaration statement
The EUT reset during the test, but could self-recover after the test.
(This permissive loss of performance was met the specication of EUT.)
Recommended separation distances between portable and mobile RF communications equipment
and the DR-17G and DR-22G
The DR-17G and DR-22G is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the DR-17G and DR-22G can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the DR-17G and DR-22G as recommended below, according
to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter (W)
Separation distance according to frequency of transmitter (m)
150kHz to 80MHz
  1.2   80MHz to 800MHz   1.2   800MHz to 2.5GHz   2.  
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
“d” in meters (m) can be estimated using the equation applicable to the frequency of the transmitter,
where “P” is the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
Cable length
Power Cord : Accessory 1.8m

PRECAUTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of
a potential haza rd that could result
in personal injury or damage to the
product.
ISO 7010-M002: Follow instructions
for use
This icon indicates important
operating and servicing information. This icon indicates complies with the 93/42/EEC, EN60601-1, EN 60601-
1-2 of related European standards.
IEC 60417-5009 : STAND-BY IEC 60417-5031 : Direct Current
IEC 60417-5032: Alternating Current IEC 60417-5021: Equipotentiality
Notice
• Read this User Manual carefully before using the LCD display and ke ep it for future reference.
•The product specications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
displays.agneovo.com.
• To register online, go to displays.agneovo.com.
• To protect your rights as a consumer, do not remove any sticke rs from the LCD display. Doing so may
affect the determination of the warranty period.
Precautions

11
PRECAUTIONS
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doing so may cause accidental re, electric shock or damage the CD display.

12
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
display and be easily accessible.
If an extension cord is used with the LCD display,
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
may be stepped on.
If the CD display will not be used for an indenite
period of time, unplug the power cord from the
power outlet.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
cause re or electric shock.
The mains plug or appliance coupler is used as
the disconnect device, the disconnect device
shall remain readily operable. Always completely
disconnect the power cord set from your product
whenever you are worki ng or cleaning on it. Do not
make connections while the power is on, because
a sudden rush of power can damage sensitive
electronic components.
Do not unplug or touch the power cord with wet
hands.
Warning:
Unplug the power cord
from the power outlet and
refer to qualied service
personnel under the following
conditions:
♦When the power cord is
damaged.
♦If the LCD display has been
dropped or the housing has
been damaged.
♦If the LCD display emits smoke
or a distinct odor.
Warning:
Ceiling mount or mount
on any other horizo ntal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

13
PRECAUTIONS
Cleaning and Maintenance
Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for
cleaning. Use a damp cloth. Keeping to clean your monitor by monthly.
The LCD display comes with NeoVTM Optical Glass. Use a soft cloth to clean the glass surface
and the housing. The display can be cleaned using a cloth moistened with 95% ethyl alcohol.
Do not rub or tap the surface of the glass with sharp or abrasive items such as a pen or
screwdriver. This may result in scratching the surface of the glass.
Do not attempt to service the CD display yourself, refer to qualied service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch deskt op backg rounds regularly.
• Adjust the LCD display to low brightness settings.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilize s.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.
The intended use of the DR-17G, DR-22G is to serve as a LCD monitor for integration with the hospital
system.It is designed for general purpose for adults using at hospital environment,continuous operation. For
displaying and viewing of images for reference. The use of this device does not require any direct contact
with patients. It shall not be used for diagnostic purpose nor for life supporting system.

14
PRECAUTIONS
Notice for the LCD Display
Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonize d IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065
for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment).
Furthermore all congurations shall comply with the system standard IEC 60601-1. Everybody who
connects additional equipment to the signal input part or signal output part congures a medical system,
and is therefore, responsible that the system complies with the requirements of the system standard
IEC 60601-1. The unit is for exclusive interconnection with IEC 60601-1 certied equipment in the patient
environment and IEC 60 certied equipment outside of the patient environment. If in doubt, consult the
technical services department or your local representative.
Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle
marke d “Hospital Only” or “Hospital Grade”.
Use a power cord that matches the voltage of the power outlet, which has been approved and complies
with the safety standard of your particular country.
The single device output analog signals through ADC element (Analog DigitalConvert) conversion to
become a digital signal and the video signal is via Video Decorder conversion. It has become the same
digital signal, these signals via Scaler IC as zoom in or out action and digital image processing, then
through the cable line transmission LVDS signals to one of the LCD module. The last by the clock controller
(Timing Controller, TCON), the clock signal is transmitted to the drive IC on the panel and turn on Backl ight
for LCD module light source by Scaler control.
WARNING – No protection against the ingress of water : IPX0
WARNING – Do not modify this equipment without authoriza tion of the manufacturer.
Installation and OSD adjusting should only be carried by manufacturer trained and authorize d personnel.
WARNING – To avoid risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
CAUTION: This adapter Manufacturer/model is a forming part of the medical device.
 Power by class I power supply.
 Adapter manufacturer/model
ADAPTER TECH: ATM065T-P240
Input/output: 100-240V~50-60Hz, 24V( ) 2.71A.
WARNING: Use suitable mounting apparatus to avoid risk of injury.
WARNING The equipment not suitable for use in the presence of a ammable anesthetic mixture with air
or with oxygen or nitrous: Not AP orAPG Category
CAUTION: No applied part.
Make sure the user not to contact SIP/SOPs and the patient at the same time.
CAUTION Transport should only be undertaken in a at surface.

15
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents
When unpacki ng, check if the following items are included in
the packa ge. If any of them is missing or damaged, contact your
dealer.
Quick Start Guide
Power cord
Note:
♦The pictures are for reference
only. Actual items may vary
upon shipment.
VGA cable
Power adapter
DR-17G & DR-22G
displays.agneovo.com
DR-17G/DR-22G_Quick Guide_V010
Quick Start Guide
DR-17G & DR-22G LCD Monitor
LCD Display
Audio cable
Note:
Must use only the supplied power
adapter:
♦ADAPTER TECH
Model no.: ATM065T-P240
Rating: 24V/2.71A
Chapter 1: Product Description
Warranty card
DR-17G DR-22G

16
PRODUCT DESCRIPTION
1.2 Wall Mounting Installation Preparation
1.2.1 Wall Mounting
1Remove the base stand.
See procedures below.
2Wall mount the LCD display.
Screw the mounting bracke t to the VESA holes at
the rear of the LCD display.
100 mm
75 mm
100 mm 75
mm
DR-17G
100 mm
75 mm
100 mm 75
mm
DR-22G
Note:
Take measures to prevent the
LCD display from falling down
and lessen possible injury and
damage to the display in case of
earthquake s or other disasters.
♦Use only the 75 x 75 mm and
100 x 100 mm wall mount ki t
recommended by AG Neovo.
♦Secure the LCD display on a
solid wall strong enough to bear
its weight.
Note:
To protect the glass panel, place a
towel or soft cloth before laying the
LCD display down.
Warning:
Ceiling mount or mount
on any other horizo ntal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizo ntal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

17
PRODUCT DESCRIPTION
1.2.2 Removing the Base Stand
1 ay the CD display face down on a at even surface.
2 Remove the screws* securing the base stand from the LCD
display.
3 Detach the base stand.
DR-17G
DR-22G
Note:
(*) The screw size is M4 x 10mm.

18
PRODUCT DESCRIPTION
1.3 LCD Display Overview
1.3.1 Front View and Keypad Buttons
53 64 871 2
7
6
4
5
2
3
1
8
DR-17G
DR-22G

19
PRODUCT DESCRIPTION
1AUTO
Hot Key: Auto Adjustment/Rotate
• For VGA input signal source, press to
perform auto adjustment.
• Press for 3 seconds to enable the Rotate
function.
• When OSD menu is ON, press to close the
OSD menu or exit a submenu.
2LEFT
Hot Key: Audio Volume Adjustment
• Press to display the volume bar. Then press
the LEFT ke y to decrease the volume.
• When OSD menu is ON, press to select an
option or adjust the settings.
3RIGHT
Hot Key: Screen Freeze
• Press to activate the screen freeze function.
To deactivate, press any ke y except for the
Power ke y.
• When the volume bar appears, press to
increase the volume.
• When OSD menu is ON, press to select
and option, adjust the settings, or enter the
submenu.
4UP
Hot Key: PIP/PBP Select
• Press repeatedly to select PIP/PBP option
(PIP  PP  FF).
• When OSD menu is ON, press to select an
option or adjust the settings.
5DOWN
Hot Key: PICTURE MODE Select
• Press repeatedly to select PICTURE MODE
option (tandard  VIDE).
• When OSD menu is ON, press to select an
option or adjust the settings.
• When PIP is ON, press to swap the PIP
main and sub picture.
6MENU
Press to display/hide the OSD menu.
7SOURCE
Press to select the input signal source.
8POWER and LED Indicator
• Press to turn the power on or off.
• Indicate the operating status of the LCD
display:
- Lights Green when the LCD display is
turned on.
- Lights Amber when the LCD display is in
standby mode.
- Lights Off when the LCD display is turned
off.

20
PRODUCT DESCRIPTION
1.3.2 Rear View
S-VIDEO
COMPOSITE-1
AUDIO
IN
L
R
IN
OUT
COMPOSITE-2
IN
OUT
AUDIO
OUT
USB (SERVICE)
RS232
L
R
AUDIO INDVIDC IN HDMI DisplayPort VGA
1DC IN
Connect with the supplied power adaptor.
2DVI
Connect DVI signals input.
3HDMI
Connect HDMI signals input.
4DisplayPort
Connect DisplayPort signals input.
5VGA
Connect VGA signals input.
6AUDIO IN
Connect audio signals input (3.5 mm Stereo
Audio Ja ck).
7S-VIDEO
Connect S-Video signals input.
8COMPOSITE-1/COMPOSITE-2 IN
Connect Composite (CVBS) signals input.
9COMPOSITE-1/COMPOSITE-2 OUT
Connect Composite (CVBS) signals output.
10 AUDIO IN
Connect audio signals input (RCA Stereo
Audio Ja ck) .
11 AUDIO OUT
Connect audio signals output (RCA Stereo
Audio Ja ck) .
12 USB (SERVICE)
Connect USB 2.0 for service.
13 RS232
Connect RS232 input from external
equipment.
14 GROUNDING STUD
Connect to a proper earth ground.
1 2 3 4 5 6
7
8
9
8
9
12
13
10
14
14
DR-17G DR-22G
11