Agilent Technologies N9010AK-REA User manual

Agilent Technologies
N9010/20/30AK-REA
Installation Guide
Refer to Agilent X Series Signal Analyzers
Option SSD Solid State Disk Drive
Installation Note (N9030-90009)
Manufacturing Part Number: N9030-90019
Printed in USA: July 2011
Supersede: March 2010
© Copyright Agilent Technologies, Inc. 2010, 2011

ii Installation Guide
Warranty Statement
THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT
TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL
WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND
ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN.
SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH
WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT
WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL
CONTROL.
DFARS/Restricted Rights Notice
If software is for use in the performance of a U.S. Government prime contract or
subcontract, Software is delivered and licensed as “Commercial computer software” as
defined in DFAR 252.227-7014 (June 1995), or as a “commercial item” as defined in FAR
2.101(a) or as “Restricted computer software” as defined in FAR 52.227-19 (June 1987) or
any equivalent agency regulation or contract clause. Use, duplication or disclosure of
Software is subject to Agilent Technologies’ standard commercial license terms, and
non-DOD Departments and Agencies of the U.S. Government will receive no greater than
Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users
will receive no greater than Limited Rights as defined in FAR 52.227-14 (June 1987) or
DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any technical data.

Installation Guide iii
Safety Notes
The following safety notes are used throughout this document. Familiarize yourself with
each of these notes and its meaning before performing any of the procedures in this
document.
WARNING Warning denotes a hazard. It calls attention to a procedure
which, if not correctly performed or adhered to, could result in
injury or loss of life. Do not proceed beyond a warning note
until the indicated conditions are fully understood and met.
CAUTION Caution denotes a hazard. It calls attention to a procedure that, if not
correctly performed or adhered to, could result in damage to or
destruction of the instrument. Do not proceed beyond a caution sign
until the indicated conditions are fully understood and met.
Definitions
•Specifications describe the performance of parameters covered by the product warranty
(temperature –0 to 55 °C, unless otherwise noted.)
•Typical describes additional product performance information that is not covered by the
product warranty. It is performance beyond specification that 80% of the units exhibit
with a 95% confidence level over the temperature range 20 to 30 °C. Typical
performance does not include measurement uncertainty.
•Nominal values indicate expected performance or describe product performance that is
useful in the application of the product, but is not covered by the product warranty.
•Characteristic Performance describes performance parameter that the product is
expected to meet before it leaves the factory, but is not verified in the field and is not
covered by the product warranty. A characteristic includes the same guard bands as a
specification.

iv Installation Guide

Contents
Contents-1
N9010/20/30AK-REA
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Verifying the Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Customer Furnished Equipment (CFE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Utilities, Adjustments, and Performance Verification Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Utilities Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Adjustments Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Performance Testing Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hard Drive Disk or Solid State Drive Replacement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing the HDD/SSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Return for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Earth Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connector Care and Cleaning Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrostatic Discharge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Instrument Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Battery Collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Compliance with German Noise Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Agilent Support, Services, and Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Service and Support Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contacting Agilent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Shipping Your Product to Agilent for Service or Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contents-2
Contents

N9030-90019 1
N9010/20/30AK-REA

2N9030-90019
N9010/20/30AK-REA Description
Description
The Agilent N9010/20/30AK Option REA provides the capability to relocate the
instrument disk drive from the internal drive drawer, to an external customer supplied
enclosure. This is accomplished by installing an eSATA drive adapter into the CPU rear
panel slot, normally occupied by the internal disk drive. An eSATA cable (also customer
supplied) connects the eSATA adapter to the external drive enclosure. The purpose is to
allow easier access to the drive, especially rack mounted instruments or secure locations.
The CPU in the N9010A and N9020A instrument must be equipped with a removable disk
drive. Early N9010A or N9020A instruments without removable disk drives will require
installation of Option AK-PC2 (CPU with removable drive). All N9030A instruments have
removable disk drives.
For additional information, please go to: http://www.agilent.com/find/security
IMPORTANT For further information refer to Agilent X Series Signal Analyzers, Option
SSD Solid State Disk Drive Installation Note (N9030-90009).
Description Item
Products Affected: N9010/20/30A with removable HDD or SSD
drive
Serial Numbers: N9010A with Option PC2
To Be Performed By: ( ) Agilent Service Center
( ) Personnel Qualified by Agilent
(X) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time:
2.0 Hours
0 Hours

N9030-90019 3
N9010/20/30AK-REA Verifying the Shipment
Verifying the Shipment
Inspect the shipping container. If the container or packing material is damaged, it should
be kept until the contents of the shipment have been checked mechanically and electrically.
If there is physical damage please notify the nearest Agilent Technologies office. Refer to
“Agilent Support, Services, and Assistance” on page 12. Keep the damaged shipping
materials (if any) for inspection by the carrier and an Agilent Technologies representative.
Customer Furnished Equipment (CFE)
❏eSATA Cable
❏2.5 inch SATA HDD enclosure
Tools Required
❏Torx Driver T-10
❏USB Mouse
❏USB Keyboard
Utilities, Adjustments, and Performance Verification Tests
Utilities Required
None
Adjustments Required
None
Performance Testing Required
None
Table 1 N9010/20/30AK-REA Content List
Description Agilent Part
Number Qty
Tray Assy eSATA W1312-60070 1
N9010/20/30AK Installation Guide N9030-90019 1

4N9030-90019
N9010/20/30AK-REA Hard Drive Disk or Solid State Drive Replacement Procedure
Hard Drive Disk or Solid State Drive Replacement
Procedure
The hard disk drive and solid state disk drive will be referred to as HDD/SSD through out
this document.
CAUTION Follow the appropriate Electrostatic Discharge (ESD) procedures. ESD can
damage or destroy electronic components. All work on electronic assemblies
should be performed at a static-safe workstation. Refer to the documentation
that pertains to your instrument for information about static-safe
workstations and ordering static-safe accessories.
Removing the HDD/SSD
1. Turn the instrument off and remove the AC power cord.
2. Using a T-10 torx driver, loosen the rear panel thumb screw and remove the existing
disk drive tray assembly from the instrument.
Figure 1 HDD/SSD Removal
Thumb
screw

N9030-90019 5
N9010/20/30AK-REA Hard Drive Disk or Solid State Drive Replacement Procedure
3. Remove the 2.5 inch HDD/SSD from its tray assembly by removing the 4 screws.
NOTE The tray assembly must be kept for use when returning the instrument for
calibration or repair.
4. Install the HDD/SSD drive into the eSATA enclosure (CFE). Follow the instructions that
are included with the enclosure.
Figure 2 SATA Tray Assembly
5. Mount the 2.5 inch eSATA enclosure in the desired location. Follow the instructions that
are included with the enclosure.
6. Install the removable tray assembly eSATA (W1312-60070) in the instrument.
Torque to 9 in-lb.
7. Connect the eSATA cable (CFE) from the removable tray assembly eSATA to the
enclosure.
8. Provide power per the enclosure instructions.
9. Install the instruments AC power cord and turn on the instrument.
Return for Service
1. Remove the eSATA drive adapter from the instrument.
2. Remove the HDD/SSD from the enclosure and install it into the original tray.
3. Place the original tray in the instrument. Refer to “Agilent Support, Services, and
Assistance” on page 12

6N9030-90019
N9010/20/30AK-REA Safety and Regulatory Information
Safety and Regulatory Information
Introduction
Review this product and related documentation to familiarize yourself with safety
markings and instructions before you operate the instrument.
This product has been designed and tested in accordance with accepted industry
standards, and has been supplied in a safe condition. The documentation contains
information and warnings that must be followed by the user to ensure safe operation and
to maintain the product in a safe condition.
Safety Earth Ground
WARNING This is a Safety Class I Product (provided with a protective earthing
ground incorporated in the power cord). The mains plug shall be
only be inserted in a socket outlet provided with a protective earth
contact. Any interruption of the protective conductor inside or
outside of the product is likely to make the product dangerous.
Intentional interruption is prohibited.
CAUTION Always use the three prong AC power cord supplied with this product. Failure
to ensure adequate earth grounding by not using this cord may cause product
damage and the risk of electrical shock.
Declaration of Conformity
A copy of the Declaration of Conformity is available upon request, or a copy is available on
the Agilent Technologies web site at
http://regulations.corporate.agilent.com/DoC/search.htm
Statement of Compliance
This instrument has been designed and tested in accordance with CAN/CSA 22.2
No. 61010-1-04, UL Std No. 61010-1 (2nd Edition).

N9030-90019 7
N9010/20/30AK-REA Safety and Regulatory Information
Before Applying Power
Verify that the premises electrical supply is within the range of the instrument. The
instrument has an autoranging power supply.
WARNING If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.
CAUTION The Mains wiring and connectors shall be compatible with the connector used
in the premise electrical system. Failure, to ensure adequate earth grounding
by not using the correct components may cause product damage, and serious
injury.
CAUTION This product is designed for use in Installation Category II and Pollution
Degree 2, per IEC 61010 (Second Edition).
CAUTION Before switching on this instrument, make sure the supply voltage is in the
specified range.
CAUTION Verify that the premise electrical voltage supply is within the range specified
on the instrument.
CAUTION Ventilation Requirements: When installing the instrument in a cabinet,
the convection into and out of the instrument must not be restricted. The
ambient temperature (outside the cabinet) must be less than the maximum
operating temperature of the instrument by 4 °C for every 100 watts
dissipated in the cabinet. If the total power dissipated in the cabinet is
greater than 800 watts, forced convection must be used.

8N9030-90019
N9010/20/30AK-REA Safety and Regulatory Information
Servicing
WARNING These servicing instructions are for use by qualified personnel only. To
avoid electrical shock, do not perform any servicing unless you are
qualified to do so.
WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended. Discard used batteries according to
manufacturer’s instructions.
WARNING For continued protection against fire hazard replace line fuse only with
same type and rating. The use of other fuses or material is prohibited.
WARNING These servicing instructions are for use by qualified personnel only. To
avoid electrical shock, do not perform any servicing unless you are
qualified to do so.
WARNING The opening of covers or removal of parts is likely to expose the user to
dangerous voltages. Disconnect the instrument from all voltage sources
before opening.
WARNING No operator serviceable parts inside. Refer servicing to qualified personnel.
To prevent electrical shock, do not remove covers.
WARNING The detachable power cord is the instrument disconnecting device. It
disconnects the mains circuits from the mains supply before other parts of
the instrument. The front panel switch is only a standby switch and is not a
LINE switch (disconnecting device).
Connector Care and Cleaning Precautions
Remove the power cord to the instrument. To clean the connectors use alcohol in a well
ventilated area. Allow all residual alcohol moisture to evaporate, and fumes to dissipate
prior to energizing the instrument.
WARNING To prevent electrical shock, disconnect the Agilent Technologies
N9010/20/30AK-REA from mains electrical supply before cleaning. Use
a dry cloth or one slightly dampened with water to clean the external
case parts. Do not attempt to clean internally.
WARNING If flammable cleaning materials are used, the material shall not be stored,
or left open in the area of the equipment. Adequate ventilation shall be
assured to prevent the combustion of fumes, or vapors.

N9030-90019 9
N9010/20/30AK-REA Electrostatic Discharge Protection
Electrostatic Discharge Protection
Protection against electrostatic discharge (ESD) is essential while removing assemblies
from or connecting cables to the instrument. Static electricity can build up on your body
and can easily damage sensitive internal circuit elements when discharged. Static
discharges too small to be felt can cause permanent damage. To prevent damage to the
instrument:
•always have a grounded, conductive table mat in front of your test equipment.
•always wear a grounded wrist strap with grounding cord, connected to a grounded
conductive table mat, having a 1 MΩresistor in series with it, when handling
components and assemblies or when making connections.
•always wear a heel strap (9300-1126) when working in an area with a conductive floor.
If you are uncertain about the conductivity of your floor, wear a heel strap.
•always ground yourself before you clean, inspect, or make a connection to a
static-sensitive device or test port. You can, for example, grasp the grounded outer shell
of the test port or cable connector briefly.
•always ground the center conductor of a test cable before making a connection to the
analyzer test port or other static-sensitive device. This can be done as follows:
1. Connect a short to one end of the cable to short the center conductor to the outer
conductor.
2. While wearing a grounded wrist strap, grasp the outer shell of the cable connector.
3. Connect the other end of the cable to the test port and remove the short from the
cable.
Figure 3 ESD Protection Setup

10 N9030-90019
N9010/20/30AK-REA Regulatory Information
Regulatory Information
This section contains information that is required by various government regulatory
agencies.
Instrument Markings
The instruction documentation symbol. The product is marked with this symbol
when it is necessary for the user to refer to the instructions in the documentation.
This symbol indicates that the instrument requires alternating current (ac) input.
This symbol indicates separate collection for electrical and electronic equipment,
mandated under EU law as of August 13, 2005. All electric and electronic equipment
are required to be separated from normal waste for disposal (Reference WEEE
Directive, 2002/96/EC).
This symbol indicates that the power line switch is ON.
This symbol indicates that the power line switch is in the STANDBY position.
This symbol indicates that the power line switch is in the OFF position.
This symbol is used to identify a terminal which is internally connected to the
product frame or chassis.
The CE mark is a registered trademark of the European Community. (If accompanied
by a year, it is when the design was proven.)
The CSA mark is a registered trademark of the CSA International. This instrument
complies with Canada: CSA 22.2 No. 61010-1-04.
This is a symbol of an Industrial Scientific and Medical Group 1 Class A product
(CISPR 11, Clause 54)
This is a marking to indicate product compliance with the Canadian
Interference-Causing Equipment Standard (ICES-001).
Direct Current.
IP 2 0 The instrument has been designed to meet the requirements of IP 2 0 for egress and
operational environment.
This is a required mark signifying compliance with an EMC requirement. The C-Tick
mark is a registered trademark of the Australian Spectrum Management Agency.
China RoHS regulations include requirements related to packaging, and require
compliance to China standard GB18455-2001.
This symbol indicates compliance with the China RoHS regulations for
paper/fiberboard packaging.
ICES/NMB-001

N9030-90019 11
N9010/20/30AK-REA RegulatoryInformation
Battery Collection
Do not throw batteries away but collect as small chemical waste, or in accordance with
your country’s requirements. You may return the battery to Agilent Technologies for
disposal. Refer to “Contacting Agilent” on page 12 for assistance.
Compliance with German Noise Requirements
This is to declare that this instrument is in conformance with the German Regulation on
Noise Declaration for Machines (Laermangabe nach der Maschinenlaermrerordnung-3.
GSGV Deutschland).
EMC Information
Complies with European EMC Directive 2004/108/EC
• IEC/EN 61326-1
• CISPR Pub 11 Group 1, class A
• AS/NZS CISPR 11
• This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB du Canada.
Acoustic Noise Emission/Geraeuschemission
LpA<70 dB Lpa<70 dB
Operator Position am Arbeitsplatz
Normal Operation normaler Betrieb
per ISO 7779 nach DIN 45635 t .19

12 N9030-90019
N9010/20/30AK-REA Agilent Support, Services, and Assistance
Agilent Support, Services, and Assistance
Service and Support Options
The standard product warranty is a one-year return to Agilent Technologies service
warranty.
NOTE There are many other repair and calibration options available from the
Agilent Technologies support organization. These options cover a range of
service agreements with varying response times. Contact Agilent for
additional information on available service agreements for this product.
Contacting Agilent
Assistance with test and measurements needs and information or finding a local Agilent
office are available on the Web at:
http://www.agilent.com/find/assist
If you do not have access to the Internet, contact your field engineer.
NOTE In any correspondence or telephone conversation, refer to the Agilent product
by its model number and full serial number. With this information, the
Agilent representative can determine the warranty status of your unit.
Shipping Your Product to Agilent for Service or Repair
IMPORTANT Agilent Technologies reserves the right to reformat or replace the internal
hard disk drive in your analyzer as part of its repair. This will erase all user
information stored on the hard disk. It is imperative, therefore, that you
make a backup copy of your critical test data located on the analyzer’s hard
disk before shipping it to Agilent for repair.
If you wish to send your instrument to Agilent Technologies for service or repair:
• Include a complete description of the service requested or of the failure and a
description of any failed test and any error message.
• Remove and retain the front handles and all rack mount hardware. The analyzer
should be sent to Agilent in the same configuration as it was originally shipped.
• Ship the analyzer using the original or comparable antistatic packaging materials.
• Contact Agilent for instructions on where to ship your analyzer.