Agilent Technologies PNA Series Installation and operation manual

Agilent Part Number: E8801-90024
Printed in USA December 2001
Installation Note
Configurable Test Set Upgrade Kit
For PNA Series RF Network Analyzers (E8801A, E8802A, and E8803A)
Network Analyzer
Model Number Upgrade Kit Part Number
E8801A, E8802A, E8803A E8801-60103

Notice.
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. Agilent shall not be liable
for errors contained herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
© Copyright 2001 Agilent Technologies, Inc. All rights reserved.

Installation Note E8801-90024 3
About the Upgrade Kit
If you need assistance, refer to “Getting Assistance from Agilent” on page 5.
Description of Option 014
An Option 014 analyzer can be configured to measure high-power devices and devices for high
dynamic range.
For a high-power measurement, external amplifiers and high power attenuators or isolators
can be added to complete the test setup. In this configuration, test-port output-power up to
1 Watt (+30 dBm) can be applied to the device under test (DUT). Additionally, there is an
external reference input that allows the external amplifier’s frequency response and drift to
be ratioed out. There are also internal step attenuators between the coupler and the receivers
to prevent receiver overload.
For high dynamic range measurements, front panel jumpers are moved to reverse the signal
path through one of the couplers. This allows for a 15 dB improvement in transmitted signal
sensitivity in one direction only. These jumpers are installed on both ports allowing the user
to choose a high dynamic range measurement in either the forward or reverse direction.
Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8801A, E8802A, and E8803A; all options
Installation to be performed by . . . . . . . . . . . . . . Agilent service center, personnel qualified
by Agilent, or customer
Estimated installation time . . . . . . . . . . . . . . . . . 2 hours
Estimated verification time . . . . . . . . . . . . . . . . . 5 minutes

4 Installation Note E8801-90024
Items Included in the Upgrade Kit
Table 1 lists the parts included in this upgrade kit, Agilent part number E8801-60103. Check
the contents of your kit against this list. If any item is missing or damaged, contact Agilent
Technologies. Refer to “Getting Assistance from Agilent” on page 5.
Table 1 Contents of Option 014 Upgrade Kit (E8801-60103)
Ref Des Description Qty Part
Number
Installation note (this document) 1 E8801-90024
SMA feed-through connectors, female SMA to female SMA 10 1250-1251
W51 RF cable, A12 source assembly to front panel R Out 1 E8801-20002
W52 RF cable, A22 RF switch to front panel port 1 Source Out 1 E8801-20004
W54 RF cable, A22 RF switch to front panel port 2 Source Out 1 E8801-20010
W55 RF cable, front panel port 1 Coupler In to A24 test port 1 coupler 1 E8801-20012
W56 RF cable, front panel port 2 Coupler In to A26 test port 2 coupler 1 E8801-20008
W57 RF cable, A24 test port 1 coupler to front panel A out 1 E8801-20013
W59 RF cable, A26 test port 2 coupler to front panel B out 1 N3381-20013
W60 RF cable, front panel jumper 5 E8356-20072
W61 RF cable, front panel A In to A18 receiver A 1 E8801-20003
W62 RF cable, front panel R In to A19 receiver R 1 E8801-20001
W64 RF cable, front panel B In to A21 receiver B 1 E8801-20007
Lower front panel overlay 1 E8801-80003

Installation Note E8801-90024 5
Getting Assistance from Agilent
By internet, phone, or fax, get assistance with all your test and measurement needs.
Table 2 Contacting Agilent
Online assistance: www.agilent.com/find/assist
United States
(tel) 1 800 452 4844 Latin America (tel) [phone]
(fax) [phone]
Canada
(tel) 1 877 894 4414
(fax) [phone]
Europe
(tel) ([phone]
(fax) ([phone]
Australia
(tel) 1 800 629 485
(fax) ([phone]
New Zealand
(tel) 0 800 738 378
(fax) ([phone]
Japan
(tel) ([phone]
(fax) ([phone]
Singapore
(tel) 1 800 375 8100
(fax) (65) 836 0252
Malaysia
(tel) 1 800 828 848
(fax) 1 800 801 664
India
(tel) 1 600 11 2929
(fax) 000 800 650 1101
Hong Kong
(tel) 800 930 871
(fax) (852) 2506 9233
Taiwan
(tel) 0800 047 866
(fax) (886) 2 25456723
Philippines
(tel) (632) 8426802
(tel) (PLDT subscriber only)
1 800 16510170
(fax) (632) 8426809
(fax) (PLDT subscriber only)
1 800 16510288
Thailand
(tel) (outside Bangkok)
[phone]
(tel) (within Bangkok)
[phone]
(fax) (66) 1 661 3714
People’s Republic of China
(tel) (preferred)
800 810 0189
(tel) (alternate)
10800 650 0021
(fax) 10800 650 0121

6 Installation Note E8801-90024
Installation Procedure for the Upgrade Kit
The network analyzer must be in proper working condition prior to installing this option. Any
necessary repairs must be made before proceeding with this installation.
WARNING This installation requires the removal of the analyzer’s protective outer
covers. The analyzer must be powered down and disconnected from the
mains supply before performing this procedure.
Electrostatic Discharge Protection
Protection against electrostatic discharge (ESD) is essential while removing or connecting
cables or assemblies within the network analyzer.
Static electricity can build up on your body and can easily damage sensitive internal circuit
elements when discharged. Static discharges too small to be felt can cause permanent
damage. To prevent damage to the instrument:
•always wear a grounded wrist strap havinga1MΩresistor in series with it when handling
components and assemblies.
•always use a grounded, conductive table mat while working on the instrument.
•always wear a heel strap when working in an area with a conductive floor. If you are
uncertain about the conductivity of your floor, wear a heel strap.
Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to
“Tools and Equipment Required for the Installation” on page 7 for part numbers.
Figure 1 ESD Protection Setup

Installation Note E8801-90024 7
Overview of the Installation Procedure
The following steps comprise the installation of the Option 014 upgrade kit.
1. Remove the outer cover.
2. Remove the front panel assembly.
3. Remove the standard instrument cables.
4. Install the Option 014 cables and front panel connectors.
5. Replace the lower front panel overlay.
6. Reinstall the front panel assembly.
7. Reinstall the outer cover.
8. Enable Option 014.
9. Verify that Option 014 is enabled.
Tools and Equipment Required for the Installation
CAUTION Use a 5/16-in torque wrench set to 10 in-lbs on all SMA cable connections except
the front-panel SMA feed-through connectors to which the front-panel jumpers
attach. Use a 5/16-in torque wrench set to 21 in-lbs for these connections.
Description Qty Part Number
T-10 TORX driver (set to 9 in-lbs) 1 N/A
T-20 TORX driver (set to 21 in-lbs) 1 N/A
5/16 in torque wrench (set to 10 in-lbs) 1 N/A
5/16 in torque wrench (set to 21 in-lbs) 1 N/A
ESD grounding wrist strap 1 9300-1367
5 ft grounding cord for wrist strap 1 9300-0980
2 x 4 ft conductive table mat and 15 ft grounding wire 1 9300-0797
ESD heel strap (for use with conductive floors) 1 9300-1308

8 Installation Note E8801-90024
Step 1. Remove the Outer Cover
CAUTION This procedure is best performed with the analyzer resting on its front handles
in the vertical position. Do not place the analyzer on its front panel without the
handles. This will damage the front panel assemblies.
Refer to Figure 2 for this procedure.
1. Disconnect the power cord (if it has not already been disconnected).
2. With a T-20 TORX driver, remove the strap handles (item ①) by loosening the screws
(item ②) on both ends until the handle is free of the analyzer.
3. With a T-20 TORX driver, remove the four rear panel feet (item ③) by removing the center
screws (item ④).
4. Slide the four bottom feet (item ⑤) off the cover.
5. Slide the cover off of the frame.
Figure 2 Outer Cover Removal

Installation Note E8801-90024 9
Step 2. Remove the Front Panel Assembly
Refer to Figure 3 for this procedure.
1. With a T-10 TORX driver, remove the six screws (item ①) from the sides of the frame.
CAUTION Before removing the front panel from the analyzer, lift and support the front of
the analyzer chassis.
2. Slide the front panel over the test port connectors.
3. Disconnect the front panel interface ribbon cable (item ②). The front panel is now free
from the analyzer.
Figure 3 Front Panel Assembly Removal

10 Installation Note E8801-90024
Step 3. Remove the Standard Instrument Cables
CAUTION Use a 5/16 in torque wrench (set to 10 in-lbs) on all SMA cable connections in
this step of the procedure.
Refer to Figure 4 for this procedure.
1. Remove and discard the following cables: W2, W3, W4, W5, W6, and W7.
Figure 4 Standard Cable Removal