Agilent Technologies PSA Series Installation and operation manual

Installation Note
Part Number E4440-90632 Supersedes: E4440-90321
Printed in USA December 2008
Agilent PSA Series Spectrum Analyzers
Option 110 Preamplifier Retrofit Kit

Notice.
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including
but not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Agilent Technologies shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use
of this material.
© Copyright 2006, 2008 Agilent Technologies, Inc.

Installation Note E4440-90632 3
Preamplifier Installation Kit
Preamplifier Installation Kit
Introduction
This retrofit kit provides all parts and instructions for retrofitting the 10 MHz to 50 GHz
30 dB Preamplifier Option 110 into the PSA series analyzers.
The Option Driver Board from the kit is required to bias the preamplifier and to control
the switch that switches the preamplifier in and out of the signal path. This board also
contains the flatness compensation data for the preamplifier.
NOTE
1. This option is not compatible with the Option 1DS, 3 GHz preamplifier. Option 1DS
must be uninstalled before installing Option 110. Damage to the instrument may result
if they are both installed.
2. The installation of this kit requires that some performance testing be performed in
order to assure the new option is functioning properly. This installation note includes a
list of required performance tests. Completing the performance tests does not guarantee
the instrument meets all specifications.
3. The instrument end user must determine whether they need a full instrument
calibration following the installation of the kit. If a full calibration is required,
arrangements regarding the level of calibration must be made between the end user and
the calibration provider.
4. This option is licensed for one instrument model/serial number combination. The
license key will only install on the designated instrument.
Products Affected: PSA E4446A
PSA E4447A
PSA E4448A
Serial Numbers: US0000/US9999
MY0000/MY9999
SG0000/SG9999
To Be Performed By: (X) Agilent Service Center
(X) Personnel Qualified by Agilent
( ) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time for
Hardware Kit following Installation:
3 Hours
5 Hours (See note 2)
Additional Recommended Task Agilent recommends that a full calibration be
performed to verify instrument specifications.
(See note 3)

4Installation Note E4440-90632
Preamplifier Installation Kit
Contents
Quantity Description Agilent Part
Number
1 Installation Note This note
1 User's and Programmers Guide Vol. 1 --
1SpecsGuide --
1 Option Upgrade Entitlement Certificate 5964-5141
1 Attenuator, 3 db, 2.4mm 08490-60010
1 Microwave Amplifier 0955-1617
1 Switch 4, Microwave Switch, SW4 87222-60015
1 Option Driver Board E4440-60253
1 Bracket, Main E4440-00062
1 Bracket, Switch E4440-00063
1 Bracket, Preamp E4440-00075
1 W37, Cable, semi-rigid, low-pass filter to
A20 Low-band assembly
E4446-20037
1 W102, Cable, semi-rigid, A15 Attenuator out to switch SW4 port 1 E4446-20077
1 W103, Cable, semi-rigid, Preamp Input to switch SW4 port 2 E4446-20078
1 W104, Cable, semi-rigid, Preamp Output to switch SW4 port 3 E4446-20083
1 W106, wire harness, Option Driver P1 to Preamp E4446-60076
1 W107, Cable, semi-rigid, switch SW4 port 4 to
W34 on the RYTHM/SBTX
E4446-20072
1 W101, Cable, semi-rigid, switch SW4 port 4 to switch SW5 port 1 E4446-20081
1 W91, Cable, ribbon, Option Driver Assembly J3 to switch SW4 E4440-60455
4 Washer-LK HLCL NO. 2, .088-IN-ID 2190-0112
4 Screw, 2-56 .312 IN-LG PAN-HD-POZI 0520-0129
8 Screw, M3x0.5, 8mm long 0515-0372
3 Screw, M2.5 x 0.45, 20mm long 0515-1934
2 Screw, M3.5x0.6, 8mm long 0515-0458
1 Cable Tie 1400-0429
1 Clamp, cable, PVC 1400-0611
1 Preamp ON Max RF Level Label E4440-80581

Installation Note E4440-90632 5
Preamplifier Installation Kit
Tools Required
1. T-8 Torx driver
2. T-10 Torx driver
3. T-15 Torx driver
4. T-20 Torx driver
5. 5/16-inch open end wrench
6. 7/16-inch open end wrench
7. POZI-1 driver
❏PSA Series Spectrum Analyzer and Service Guide. This manual is available as part of
the E4446AU, E4447AU, or E4448AU Option OBW kits.
❏Calibration software. Latest software information and downloads available at
http://www.agilent.com/find/calibrationsoftware
❏Test equipment supported by the calibration software.
❏Microsoft Windows based personnel computer with LAN card and CD-ROM drive
❏Windows 2000 or Windows XP
❏Crossover cable if PC or analyzer is not connected to network. Use a CAT, RJ45 cable
with cross pinning, Agilent p/n 8121-0545.
❏Firmware revision A.09.10 or later. Download the latest version from
http://www.agilent.com/find/psa_firmware, or order the Firmware Update kit.
Depending on your model number, the firmware update kit is ordered as:
Order E444xAU (Qty.1) Option UE2 (Qty. 1), where the “x” is the last digit of the
model number. For example: E4446AU option UE2

6Installation Note E4440-90632
Installation Procedure
Installation Procedure
For assistance at any time during this procedure, get in touch with your nearest Agilent
Technologies Sales and Service Office. To find your local Agilent office access the
following URL:
http://www.agilent.com/find/assist
Preliminary Hardware Verification
1. Check for the presence of Option 1DS by pressing System, Show System, and look at
the option list.
• If Option 1DS is present it must be uninstalled before Option 110 can be installed.
a. Delete Option 1DS License by pressing System, More, More, Licensing, Option.
Use the front panel numerical key pad to enter the option designator 1DS and
press the Enter key. Press Delete Option.
b. Check that Option 1DS has been removed by pressing System, More, Show
System, and looking at the option list.
c. Follow the instructions in this installation note in the section named
“Uninstalling Option 1DS” to remove the Option 1DS hardware.*
• If Option 1DS is not present then continue with the installation of Option 110.
*Option 110 and Option 1DS are not compatible. Damage to the instrument may
result if they are both installed.
2. Check for the presence of Option 123, Preselector Bypass by pressing System, More,
Show System, and look at the option list.
• If Option 123 is present then follow the instructions in this installation note in the
section named “Installing the Preamplifier with Option 123”.
• If Option 123 is not present then follow the instructions in this installation note in
the section named “Installing the Preamplifier without Option 123”.

Installation Note E4440-90632 7
Installation Procedure
Remove the Outer Case
CAUTION If the instrument is placed on its face during any of the following
procedures, be sure to use a soft surface or soft cloth to avoid damage to
the front panel, keys, or input connector.
1. Disconnect the instrument from ac power.
2. Refer to Figure 1. Remove the two handles on the sides of the instrument as shown.
Use the T-20 driver to loosen the screws that attach each handle (1). Remove the
handles.
3. Remove the four bottom feet (2). Lift up on the tabs on the feet, and slide the feet in
the direction indicated by the arrows.
4. Remove the four screws (3) that hold the rear feet (4) in place.
5. Pull the instrument cover (5) off toward the rear of the instrument.
Figure 1 Instrument Outer Case Removal

8Installation Note E4440-90632
Installation Procedure
Remove the Top Brace
1. Refer to Figure 2. Use the T-10 driver to remove the top screws (3) (one screw is
under the security label), and the side screws (2) attaching the top brace (1) to the
deck.
2. Remove the top brace from the deck.
Figure 2 Top Brace Removal

Installation Note E4440-90632 9
Installation Procedure
Uninstalling Option 1DS
1. Locate the RF section on the right side of the instrument. Figure 3 shows cable
locations and the preamplifier mounting orientation.
Figure 3 Preamplifier Location
2. Locate and remove cable W55 (SBTX to FIFA rear connector), E4446-20045. This
cable will be replaced later. It is removed to allow the preamplifier assembly to be
removed.
3. Locate and remove cable W56 (FIFA front connector to Band Pass filter),
E4446-20046. This cable will be replaced later. It is removed to allow the preamplifier
assembly to be removed.
4. Locate and remove cable W39 (low band assembly J4 to band pass filter),
E4446-20058, using the 5/16-inch wrench. This cable will be replaced later. It is
removed to allow the preamplifier assembly to be removed.
5. Locate and remove cable W50 (preamplifier J2 and low band assembly J1 RF IN).
Discard this cable, since it will be replaced by another cable.

10 Installation Note E4440-90632
Installation Procedure
CAUTION In the following step, use a 7/16-inch wrench on one of the wrench flats
at the ends of the filter to prevent the filter body from rotating when
removing the cable. Cables can be damaged if the low pass filter is
allowed to rotate when loosening or tightening the cable connector.
6. Locate and remove cable W48 (low pass filter and J1 on the preamplifier). Discard
this cable, since it will be replaced by another cable.
7. Uninstall the preamplifier and the ribbon cable. Use a T-10 Torx driver to remove the
two screws.
Figure 4 Remove the Preamplifier