Agilent Technologies U1701B Manual

Agilent Technologies
Agilent U1701B
Dual Display Handheld
Capacitance Meter
User’s and Service Guide

II U1701B User’s and Service Guide
Notices
© Agilent Technologies, Inc. 2009, 2012
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
U1701-90055
Edition
Third Edition, June 25, 2012
Printed in Malaysia
Agilent Technologies, Inc.
5301 Stevens Creek Blvd.
Santa Clara, CA 95051 USA
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
U.S. Government Restricted Rights. Soft-
ware and technical data rights granted to
the federal government include only those
rights customarily provided to end user cus-
tomers. Agilent provides this customary
commercial license in Software and techni-
cal data pursuant to FAR 12.211 (Technical
Data) and 12.212 (Computer Software) and,
for the Department of Defense, DFARS
252.227-7015 (Technical Data - Commercial
Items) and DFARS 227.7202-3 (Rights in
Commercial Computer Software or Com-
puter Software Documentation).
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.

U1701B User’s and Service Guide III
Safety Symbols
The following symbols on the instrument and in the documentation
indicate precautions which must be taken to maintain safe operation of
the instrument.
Direct current Off (supply)
Alternating current On (supply)
Both direct and alternating
current
Equipment protected throughout
by double insulation or reinforced
insulation.
Three-phase alternating current Caution, risk of electric shock.
Earth (ground) terminal Caution, risk of danger (refer to
this manual for specific Warning
or Caution information.
Protective conductor terminal Caution, hot surface.
Frame or chassis terminal Out position of a bi-stable push
control.
Equipotentiality In position of a bi-stable push
control.

IV U1701B User’s and Service Guide
General Safety Information
The following general safety precautions must be observed during all phases of
operation, service and repair of this instrument. Failure to comply with these
precautions or with specific warnings elsewhere in this manual violates safety
standards of design, manufacture and intended use of the instrument. Agilent
Technologies assumes no liability for the customer’s failure to comply with these
requirements.
WARNING
• Read this operation manual completely before using this device and
follow all safety instructions.
• This device is for indoor use at an altitude of up to 2000 m.
• Avoid working alone.
• Use the device only as specified in this manual; otherwise, the
protection provided by the meter may be impaired.
• Never measure voltage with this meter.
• Do not use this device if it looks damaged.
• Inspect the leads for damaged insulation or exposed metal. Replace
damaged leads.
• Disconnect the power and discharge all high-voltage capacitors
before testing.
• Be cautious when working with voltages above 60 VDC or 30 VRMS
and 42.4 Vpeak, as it may cause a shock hazard.
• Always use specified battery.
• The meter is designed in compliance with IEC 61010-1.
• CE requirement: Under the influence of RF field according to
standard, the supplied test leads will pick up induced noise. To have
better shielding effect, a short-twisted lead should be used.
CAUTION
• Ensure proper insertion of battery in the meter, and follow the correct
polarity.

U1701B User’s and Service Guide V
Environment Conditions
This instrument is designed for indoor use in areas with low condensation and to
be used with standard or compatible test probes. Table 1-1 shows general
environment requirements.
Table 1 -1 Environment Requirements
Environment Conditions Requirements
Operating environment Full accuracy at 0 °C to 50 °C
Operating relative humidity Full accuracy up to 80% RH for
temperature up to 31 °C, decreasing
linearly to 50% RH at 50 °C
Storage humidity 0 – 80% R.H. non condensing
Storage environment –20 °C to 60 °C
Altitude 0 – 2000 m
Pollution Degree Pollution Degree 2

VI U1701B User’s and Service Guide
CAUTION
The U1701B dual display handheld capacitance meter complies with
the following safety and EMC requirements:
• IEC 61010-1:2001/EN 61010-1:2001 (2nd Edition)
• CISPR 11:2003+A1:2004
• IEC 61000-4-2:1995+A1:1998 +A2:2000
• IEC 61000-4-3:2006
• IEC 61000-4-4:2004
• IEC 61000-4-5:2005
• IEC 61000-4-6:2003+A1:2004+A2:2006
• IEC 61000-4-11:2004
• Canada: ICES/NMB-001:2004
• Australia/New Zealand: AS/NZS CISPR11:2004
CAUTION
Degradation of some product specifications can occur in the presence
of ambient electromagnetic (EM) fields and noise that couples to the
product's powerline, communication or I/O cables. The product
self-recovers and operates to all specifications when the source of the
ambient EM field and noise are removed or the product is protected
from the ambient EM field or the product cabling is shielded from the
ambient EM noise.

U1701B User’s and Service Guide VII
Regulatory Markings
Waste Electrical and Electronic Equipment (WEEE) Directive
2002/96/EC
This instrument complies with the WEEE Directive (2002/96/EC) marking
requirement. This affixed product label indicates that you must not
discard this electrical/electronic product in domestic household waste.
Product Category:
With reference to the equipment types in the WEEE directive Annex 1,
this instrument is classified as a “Monitoring and Control Instrument”
product. The affixed product label is shown as below:
Do not dispose in domestic household waste
To return this unwanted instrument, contact your nearest Agilent office,
or visit:
www.agilent.com/environment/product
for more information.
The CE mark is a registered trademark
of the European Community.This CE
mark shows that the product complies
with all the relevant European Legal
Directives.
The C-tick mark is a registered
trademark of the Spectrum
Management Agency of Australia. This
signifies compliance with the Australia
EMC Framework regulations under the
terms of the Radio Communication Act
of 1992.
ICES/NMB-001 indicates that this ISM
device complies with Canadian
ICES-001.
This instrument complies with the
WEEE Directive (2002/96/EC) marking
requirement. This affixed product label
indicates that you must not discard this
electrical/electronic product in
domestic household waste.

VIII U1701B User’s and Service Guide
Declaration of Conformity (DoC)
The Declaration of Conformity (DoC) for this instrument is available on
the Web site. You can search the DoC by its product model or description.
http://regulations.corporate.agilent.com/DoC/search.htm
NOTE
If you are unable to search for the respective DoC, please contact your
local Agilent representative.

U1701B User’s and Service Guide IX
In This Guide…
1Getting Started Chapter 1 introduces key features and steps to get
started with the U1701B dual display handheld capacitance meter. This
chapter also guides you through the basics of the front panel operations.
2Features and Functions Chapter 2 describes the features and
functions that are available in the U1701B dual display handheld
capacitance meter in step-by-step instructions.
3Default Setting Configurations Chapter 3 describes on how to
change and configure the default setting of the U1701B dual display
handheld capacitance meter and other setting features
4Service and Maintenance Chapter 4 provides the information on the
warranty, services, maintenance procedures and troubleshooting hints to
solve general problems that you may encounter with the meter.
5Specifications and Characteristics Chapter 5 lists U1701B‘s
electrical specifications, general specifications, and SMD Tweezer’s
specifications.

X U1701B User’s and Service Guide