Agilent Technologies E5505A User manual

Agilent Technologies
Agilent E5505A
Phase Noise
Measurement System
Installation Guide
Fifth Edition, December 2009
Create a Recovery DVD
Refer to Chapter 5, Recovery

Notices
© Agilent Technologies, Inc. 2004
No part of this manual may be reproduced
in any form or by any means (including
electronic storage and retrieval or transla-
tion into a foreign language) without prior
agreement and written consent from Agi-
lent Technologies, Inc. as governed by
United States and international copyright
laws.
Manual Part Number
E5505-90001
Edition
Fifth Edition, December 2009
Printed in USA
Agilent Technologies, Inc.
1400 Fountaingrove Pkwy
Santa Rosa, CA 95403
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connection
with the furnishing, use, or perfor-
mance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a
license and may be used or copied only in
accordance with the terms of such license.
Restricted Rights Legend
If software is for use in the performance of
a U.S. Government prime contract or sub-
contract, Software is delivered and
licensed as “Commercial computer soft-
ware” as defined in DFAR 252.227-7014
(June 1995), or as a “commercial item” as
defined in FAR 2.101(a) or as “Restricted
computer software” as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Agilent Technologies’ standard
commercial license terms, and non-DOD
Departments and Agencies of the U.S. Gov-
ernment will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Govern-
ment users will receive no greater than
Limited Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any
technical data.
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and met.
Microsoft ® is a U.S. registered trademark
of Microsoft Corporation.
Windows ® and MS Windows ®
are U.S. registered trademarks of
Microsoft Corporation.
Pentium ® is a U.S. registered trademark of
Intel Corporation.
Adobe ® Acrobat ® Adobe, the Adobe
Logo, Acrobat and the Acrobat Logo are
trademarks of Adobe Systems Incorpo-
rated.
Symantec Ghost®is a U.S. registered
trademark of Symantec Corporation

E5505A Installation Guide 3
Contents
1 General Information
Introduction 8
Table 1. E5505A installation reading road map 8
Unpacking and Inspecting the System 9
To unpack a racked system 9
To unpack a benchtop system 10
Inspecting the system 10
Table 2. E5505A connectors and adapters 11
System Overview 12
Figure 1. Agilent E5505A benchtop system, typical configuration 13
Table 3. Equivalent system/instrument model numbers 13
System Specifications 14
Table 4. Mechanical and environmental specifications 14
Table 5. Operating characteristics 14
Table 6. Amplitude ranges 15
15
Power requirements 15
Table 7. E5505A maximum AC power requirements 15
Documentation 17
Figure 2. Navigate to system documentation 17
2 Flat-Panel Display
Connecting a Rack-Mounted Flat-Panel Display 20
Table 8. Monitor, keyboard, and mouse parts listing 20
Figure 3. Display assembly installation 21
3 System Interconnections
Making Connections 24
Figure 4. Connect adapter to back of PC digitizer card 24
System Connectors 25
Table 9. E5505A connectors and adapters 25
System Cables 26
Table 10. E5505A cables and connections 26
Figure 5. System connections with test set, standard model 27
Figure 6. System connections with test set, option 001 28
Figure 7. System connections with test set, option 201 29

4E5505A Installation Guide
4 Measurement Software
Powering the System On 32
To power on a racked system 32
To power on a benchtop system 32
Starting the Measurement Software 33
Figure 8. Log-In Window 33
Figure 9. E5500 UI and Shutdown desktop shortcuts 33
Figure 10. Navigate to E5500 user interface from start menu 34
Figure 11. Main E5500 user interface window 35
Specifying Assets for the Confidence Test 36
Figure 12. Navigate to server hardware connections 36
Figure 13. Successful I/O check 37
Figure 14. Failed I/O check 37
Figure 15. Select test set, FFT analyzer, and swept analyzer 38
Running the Software Confidence Test 39
Figure 16. Opening the parameters definition file 39
Table 11. Parameter Data for the Agilent N5500A Confidence Test Example 40
Beginning the Measurement 41
Figure 17. Selecting a new measurement 41
Figure 18. Selecting a new measurement 41
Figure 19. 50 W connector location for measurement 42
Making the Measurement 42
Figure 20. Typical phase noise curve for a system confidence test 43
Congratulations 43
Additional Assets 44
Configuring an Asset 44
Figure 21. Navigate to Asset Manager 44
Figure 22. Navigate to Add in Asset Manager 45
Figure 23. Select source as asset type 45
Figure 24. Choose source 46
Figure 25. Select I/O library 47
Figure 26. Enter asset and serial number 47
Figure 27. Enter comment 48
Figure 28. Click Check button 48
Figure 29. Confirmation message 49
Verifying Server Hardware Connections 50
Figure 30. Navigate to server hardware connections 50
Figure 31. Select Sources tab 50
Figure 32. Successful I/O check 51

E5505A Installation Guide 5
Figure 33. Failed I/O check 51
Setting GPIB Addresses 53
Table 12. Default GPIB addresses 53
Figure 34. Asset Manager on System menu 54
Figure 35. Asset Manager window 54
Figure 36. GPIB address dialog box 55
Powering the System Off 56
To power off a racked system 56
To power off a benchtop system 56
Using the E5500 Shutdown Utility 56
Figure 37. Shutdown utility icon 56
5 Recovery
Hard Drive Recovery Process - Advantech PC 58
Create an Image on the Recovery DVD 58
Recover From a System Crash Using the Recovery Partition 61
Re-image a New Hard Drive Using the Recovery DVD 62
Partition a New Hard Drive Using Windows Disk Manager® 63
Create an Image on the New Recovery Partition 64
System Boot Order Check 65
Hard Drive Recovery Process - Kontron PC 66
67
Configuring recovery prompt timing 68
Hard Drive Disk Replacement Procedure 68
Figure 38. Hard Disk Drive Assembly 69
Figure 39. Ejector Lever Pulled Up 70
Figure 40. Ejector Lever Pushed Down 70
6 Preventive Maintenance
Using, Inspecting, and Cleaning RF Connectors 72
Repeatability 72
RF Cable and Connector Care 72
Proper Connector Torque 73
Table 13. Proper Connector Torque 73
Connector Wear and Damage 73
SMA Connector Precautions 74
Cleaning Procedure 74

6E5505A Installation Guide
Table 14. Cleaning Supplies Available from Agilent 75
General Procedures and Techniques 76
Figure 41. GPIB, 3.5 mm, Type-N, power sensor, and BNC connectors 76
Connector Removal 77
Instrument Removal 79
Standard instrument 79
Half-Rack-Width Instrument 80
Figure 42. Instrument lock links, front and rear 81
Benchtop Instrument 81
Instrument Installation 82
Standard rack instrument 82
Half-Rack-Width instrument 83
Benchtop instrument 83
A Service, Support, and Safety Information
Safety and Regulatory Information 86
Safety summary 86
Equipment Installation 86
Environmental conditions 87
Before applying power 87
Ground the instrument or system 88
Fuses and Circuit Breakers 88
Maintenance 89
Safety symbols and instrument markings 89
Table 15. Safety symbols and instrument markings 89
Declaration of Conformity 91
Compliance with German noise requirements 91
Table 16. German noise requirements summary 91
Compliance with Canadian EMC requirements 91
Service and Support 92
Service and Support Options 92
Contacting Agilent 92
Shipping Your Analyzer to Agilent for Service or Repair 93
Return Procedure 94
Determining your instrument’s serial number 94
Figure 43. Serial number location 94
Shipping the instrument 95

7
Agilent E5505A Phase Noise Measurement System
Installation Guide
Agilent Technologies
1
General Information
Introduction 8
Unpacking and Inspecting the System 9
System Overview 12
System Specifications 14
Documentation 17
This chapter introduces you to the Agilent E5505A Phase Noise
Measurement System. It contains an overview of the system, system
specifications, and guidelines for unpacking a system. It also provides a
reading road map for installation documentation.

8E5505A Installation Guide
1General Information
Introduction
Use this guide to unpack, connect instruments (if needed), power on,
configure, test, and power off your Agilent E5505A Phase Noise
Measurement System. For all system models, start with the information in
this chapter—especially the unpacking guidelines starting on page 10.
If you’ve ordered a racked system, it arrives as a turnkey solution—ready
to power on with all hardware and software installed. If you’ve ordered a
flat- panel display, procedures for mounting it are in Chapter 2. Follow the
powering on procedures in Chapter 4 and you’re ready to make your first
measurement.
A benchtop system arrives with all hardware and software installed, but
you must connect the instruments with the appropriate cables. You’ll find
instrument connection diagrams in Chapter 3. (Agilent ships the needed
cables with the system.) Then proceed to Chapter 4 to power on your
system and make your first measurement.
Use Table 1 as a guide to the chapters to use for your model:
•Racked system
•Benchtop system
NOTE
If you need to re-install the phase noise hardware and software in the E5505A system PC
for any reason, refer to the E5505A Phase Noise Measurement System User’s Guide for
information and procedures.
Table 1 E5505A installation reading road map
Rack Benchtop
Chapter 1, “General Information” Chapter 1, “General Information”
Chapter 2, “Flat-Panel Display” (if applicable) Chapter 3, “System Interconnections”
Chapter 4, “Measurement Software” Chapter 4, “Measurement Software”
Appendix A, “Service, Support, and Safety
Information”
Appendix A, “Service, Support, and Safety
Information”

General Information 1
E5505A Installation Guide 9
Unpacking and Inspecting the System
This section presents procedures for unpacking a racked system and a
benchtop model. Do not attempt to unpack your system without reviewing
them.
To unpack a racked system
To unpack an E5505A racked system, you need the following tools:
•Safety glasses
•Klimp hammer or prybar to remove the klimps
•Socket wrench and sockets
•Pliers
To remove the racked system from the packing crate, follow these steps:
1Remove the klimps from the crate wall marked “Ramp Panel.”
2Position the ramp panel to create a ramp. The non- hinged end rests on
the crate base and the hinged flap meets the floor.
3Secure the ramp panel to the base by placing the drop- in bolt (located
in the packing foam) through the holes in the ramp and the base of the
crate.
4Remove the remaining crate walls and top, as well as the foam padding
from the top of the cabinet and the anti- static bag covering the cabinet.
5Remove the center restraining bolts and cleats holding the cabinet to
the crate base using the socket wrench. These bolts are located on the
ramp side of the crate and the side opposite.
6Lift the side bolts from the curb gate on the ramp side of the crate base
using pliers. Remove the curb gate.
7With one person behind the system and two guiding the sides, gently
roll the system down the ramp.
NOTE
Retain all packing material—crate, foam, curb gate, bolts, cleats, and klimps—for future
use should you need to move the system to another location.
WARNING
Always wear safety glasses or goggles when removing steel clips (klimps) from
the shipping crate. These clips are under tension and when pried free can spring
back and cause injury to unprotected eyes.

10 E5505A Installation Guide
1General Information
To unpack a benchtop system
To unpack an E5505A benchtop system, you need the following tools:
•Safety glasses
•Sturdy scissors
1Cut and remove the plastic straps that secure the shipping container
and lift the lid.
2Remove and open the individual shipping boxes.
3Carefully remove the contents from each box.
Inspecting the system
After unpacking a racked or benchtop system, the next step is to inspect
the shipping container and its contents thoroughly to ensure that nothing
was damaged during shipment.
Verify that all parts and materials are included in your shipment:
•E5500 Phase Noise Measurement System software and documentation
CD- ROM
•E5500 Software Keyword Licence Certificate
•Recovery media kit for Microsoft® Windows XP Pro®
WARNING
Do not stand in the path of a system being moved down the incline of the cabinet
ramp.
NOTE
Retain all packing material—crate, pallet, boxes, foam, etc.—for future use should you
need to move the system to another location.
WARNING
Always wear safety glasses or goggles when cutting plastic straps from the
shipping container. These straps are under tension and when cut can snap and
cause injury to unprotected eyes.
NOTE
If the container or packing material is damaged, the contents should be checked both
mechanically and electrically. If the contents are damaged or defective, contact your
customer engineer through your local Agilent Technologies Service Center. Keep the
shipping materials for the transport company’s inspection.
For instructions on removing an instrument from the system, see Chapter 6. See
Appendix A for return procedures.