Agri-Fab 45-0403 User manual

PRINTED IN U.S.A. FORM NO. 40121 (4/26/07)
Model No.
45-0403
FRONT END SCOOP
OWNERS
MANUAL
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
the fastest way to purchase parts
www.speedepart.com
™
Safety
Assembly
Operating
Maintenance
Repair Parts

2
• Read this operator's manual before attempting to
assemble or operate the scoop attachment.
• Read the vehicle owner's manual and know how
to operate your vehicle before using the scoop
attachment.
• Never carry passengers in the scoop bucket. It has
not been designed to carry passengers.
• Never allow children to operate the vehicle or the
scoop attachment.
• Do not allow adults to operate the vehicle or scoop
attachment without proper instructions.
• Always begin with the transmission in rst (low) and
gradually increase speed as conditions permit.
• Drive the tractor at reduced speed over rough terrain
and hillsides or near creeks and ditches to prevent
tipping over and loss of control. Do not drive too close
to a creek or ditch.
• Never ram the scoop into material at high speed.
• Vehicle braking and stability may be affected with
the attachment of this scoop. Do not ll the scoop
to maximum weight capacity without checking the
capability of the vehicle to safely drive and stop with
the scoop attached.
• Before operating vehicle on any grade (hill) refer
to the safety rules in the vehicle owner's manual
concerning safe operation on slopes. Refer also to the
slope guide on page 23 of this manual. Stay off steep
slopes!
• Follow maintenance and lubrication instructions as
outlined in this manual.
Look for this symbol to point out important safety precautions. It means — Attention!!
Become alert!! Your safety is involved.
WHEEL WEIGHT TIRE CHAINS
SAFETY RULES
Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate
the equipment. Exercise caution at all times when using power equipment.
ACCESORIES AND ATTACHMENTS
Rear wheel weights and tire chains will provide extra traction and stability when using the Front
End Scoop attachment. These items are available where you purchased your tractor.

3
1
3
45
10
11
8
9
6
13
12
14 16
17
18
15
21
20
7
2
19
1. Bucket Assembly
2. Pin Stop Bracket
3. Lift Frame Assembly
4. Lift Bracket Assembly
5. Tilt Anchor Assembly
6. Right (Long) Side Plate
7. Left (Long) Side Plate
15.Lift Handle Tube
16.Dump Handle Tube Extension
17.Dump Pivot Bracket
18.Lift Handle Tube Extension
19.Dump Control Pin
20.Lift Cable (Short)
21.Dump Cable (Long)
8. Right (Short) Side Plate
9. Left (Short) Side Plate
10.Dump Control Rod
11.Lift Strap Assembly (2)
12.Tilt Bracket Assembly
13.Attachment Rod
14.Dump Handle Tube
CARTON CONTENTS

4
WX
AA
EE
FF
MJK
IL
H
O
ABCDEFG
P
R
S
T
QCC
V
DD
N
GG
HH
JJ
II
KK
Y
UZBB
FULL SIZE HARDWARE CHART

5
PARTS NOT SHOWN FULL SIZE
NN
LL
OO PP
MM
PARTS BAG CONTENTS
Not all parts will be needed for t-up to any one tractor.
Discard unneeded parts after assembly is nished.
REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION
A 2 Hex Bolt, 5/8" x 1-1/2"
B 2 Hex Bolt, 1/2" x 1-3/4"
C 3 Hex Bolt, 1/2" x 1"
D 2 Hex Bolt, 3/8" x 1-1/4"
E 6 Hex Bolt, 3/8" x 1"
F 5 Hex Bolt, 5/16" x 1"
G 5 Hex Bolt, 5/16" x 1-3/4"
H 3 Hex Bolt, 1/4" x 1-3/4"
I 6 Carriage Bolt, 3/8" x 1"
J 2 Carriage Bolt, 5/16" x 1"
K 2 Carriage Bolt, 1/4" x 3/4"
L 1 Slotted Truss Head Bolt, 10-32 x 5/8"
M 2 Nylock Nut, 5/8"
N 2 Nylock Nut, 1/2"
O 3 Nylock Jam Nut, 1/2"
P 2 Hex Nut, 3/8"
Q 8 Nylock Nut, 3/8"
R 12 Nylock Nut, 5/16"
S 5 Nylock Nut 1/4"
T 1 Hex Nut, 1/4"
U 1 Nylock Nut, #10-32
V 6 Lock Washer, 3/8"
W 3 Washer, 1/4"
X 8 Washer, 5/16"
Y 6 Washer, 3/8" (Small)
Z 4 Washer, 1/2" (Small)
AA 2 Washer, 3/8" (Large)
BB 6 Washer, 5/8"
CC 8 Washer, 1/2" (Large)
DD 2 Washer, 3/4"
EE 2 Washer, 1"
FF 3 Hairpin Cotter, Long
GG 4 Hairpin Cotter, Short
HH 2 Cotter Pin, 1/8" 1-1/2"
II 6 Cotter Pin, 1/8" x 1-1/4"
JJ 4 Spacer, 1/2"
KK 1 Spacer, 3/8" Small
LL 2 Clevis Pin
MM 1 Compression Spring
NN 6 Cable Tie
OO 2 Tilt Stop Bracket
PP 1 Hose Clip

6
TOOLS REQUIRED FOR ASSEMBLY
(1) #2 Phillips Screwdriver
(1) Standard Screwdriver
(2) 15/16" Wrenches (one should be box-end)
(2) 3/4" Wrenches
(2) 9/16" Wrenches
(2) 7/16" Wrenches
(2) 1/2" Wrenches
(1) 3/8" Wrench
ADDITIONAL ITEMS NEEDED
Ruler or Tape Measure
Grease
5/16" x 1"
HEX BOLT (F)
PIN STOP
BRACKET
3/8" NYLOCK NUT (Q)
3/8" x 1-1/4"
HEX BOLT (D)
3/8" HEX NUT (P)
BUCKET
ASSEMBLY
5/16" WASHERS (X)
5/16"
NYLOCK NUT (R)
FIGURE 1
5/8" x 1-1/2"
HEX BOLT (A)
APPLY
GREASE
5/8" x 1-1/2"
HEX BOLT (A)
5/8" NYLOCK
NUTS (M) APPLY GREASE
APPLY
GREASE
LIFT FRAME
ASSEMBLY
FIGURE 2
REMOVE PARTS FROM CARTON
• Remove the hardware pack and all loose parts from
the carton.
• Lay cardboard on oor to help prevent scratching of
painted parts.
• Lay out and identify all the parts and hardware as
shown on pages 3 through 5.
ASSEMBLE SCOOP
STEP 1: INSTALL TWO BOLTS
(SEE FIGURE 1)
• Assemble two 3/8" x 1-1/4" hex bolts (D) and 3/8" hex
nuts (P), threading the nut all the way onto the bolt
until it is tight against the head of the bolt.
• Install a nut/bolt assembly into the bucket assembly
and fasten using a 3/8" nylock nut (Q). Tighten.
Repeat for the other side.
STEP 2: INSTALL PIN STOP BRACKET
(SEE FIGURE 1)
• Install the pin stop bracket to the top of the bucket
assembly using four 5/16" x 1" hex bolts (F), eight
5/16" washers (X) and four 5/16" nylock nuts
(R). Center the bolts in the slots of the pin stop
bracket and the slots of the bucket.Tighten the
bracket so that it is square with the bucket.
STEP 3: INSTALL LIFT FRAME ASSEMBLY
(SEE FIGURE 2)
• Apply grease to the mounting surface of the bucket
assembly and the inside of the lift frame arms.
• Assemble the lift frame assembly to the bucket
assembly using two 5/8" x 1-1/2" hex bolts (A) and
5/8" nylock nuts (M). Tighten, then loosen the nuts
1/4 turn, or until the lift frame pivots freely.
ASSEMBLY

7
FIGURE 3
5/8" WASHER (BB)
1/8" x 1-1/4"
COTTER
PIN (II)
LIFT BRACKET
ASSEMBLY
LIFT FRAME
ASSEMBLY
1/2" NYLOCK
JAM NUTS (O)
TILT ANCHOR
ASSEMBLY
LIFT
BRACKET
ASSEMBLY
1/2" x 1"
HEX BOLT (C)
1/2" x 1"
HEX BOLT (C)
FIGURE 4
SHORT
HAIRPIN
COTTER (GG)
1/2" x 1"
CLEVIS PIN (LL)
1/2" SPACER (JJ)
1/2" WASHER
(SMALL) (Z)
SHORT HAIRPIN
COTTER (GG)
LIFT STRAP
ASSEMBLY
UPPER FRONT
MOUNTING HOLE
ARM
ARM
FIGURE 5 Bucket removed for clarity
STEP 7: INSTALL TILT BRACKET ASSEMBLY
(SEE FIGURE 6 ON NEXT PAGE)
• If you mounted the lift strap assemblies in step 6
to the rear holes instead of the front holes in the lift
frame, replace the spacer on the tilt bracket assembly
with the smaller 3/8" spacer (KK) from the parts bag
at this time.
• Loosen the bolts and nuts on the tilt bracket
assembly 1/4 turn or until the two plates of the
assembly will slide back and forth. You will retighten
them later in step 26.
STEP 4: INSTALL LIFT BRACKET ASSEMBLY
(SEE FIGURE 3)
•Assemble the lift bracket assembly to the lift frame
assembly using two 5/8" washers (BB) and 1/8" x
1-1/4" cotter pins (II).
STEP 5: INSTALL TILT ANCHOR ASSEMBLY
(SEE FIGURE 4)
• Assemble the tilt anchor assembly to the lift bracket
assembly using two 1/2" x 1" hex bolts (C) and 1/2"
nylock jam nuts (O). Tighten.
STEP 6: INSTALL LIFT STRAP ASSEMBLIES
(SEE FIGURE 5)
• Loosen the bolts and nuts on the lift strap
assemblies 1/4 turn or until the straps will slide back
and forth. You will retighten them later in step 27.
• Turn the lift strap assemblies as shown. Install each lift
strap assembly to an arm of the lift bracket assembly
and then secure with a small 1/2" washer (Z) and a
short hairpin cotter (GG).
• Position the lower end of each lift strap assembly to
the outside of the lift frame. Fasten to the upper front
holes in the lift frame using a 1/2" x 1" clevis pin (LL),
1/2" spacer (JJ) and short hairpin cotter (GG) for each
assembly.
NOTE: The lift strap assemblies may be installed in the
rear mounting holes of the lift frame to increase the lift
height, but this will also increase the lifting effort. The
front holes give a lift height of about 6-1/2" and require 28
lbs. of force to lift a 150 lb load. The rear holes will give a
lift height of about 8-1/2" and require 35 lbs. of force.

8
• Lightly apply grease to the end of the arm on the tilt
anchor assembly and install the tilt bracket assembly
to the arm using a 1/2" x 1" hex bolt (C) and 1/2"
nylock jam nut (O). Tighten. Loosen the nut 1/4 turn,
or until the tilt bracket assembly pivots freely.
• Install a 1/4" x 1-3/4" hex bolt (H) through a 1/4"
washer (W) and then through the end of the extension
spring on the tilt bracket assembly. Next, install a 1/4"
hex nut (T) all the way onto the threads of the bolt.
Finally install the end of the bolt into the hole in the
arm of the tilt anchor assembly and secure using a
1/4" nylock nut (S). Tighten.
1/4" HEX NUT (T)
1/4" NYLOCK NUT (S)
1/4" WASHER (W)
1/4" x 1-3/4"
HEX BOLT (H) 1/2" NYLOCK
JAM NUT (O)
APPLY
GREASE
1/2" x 1"
HEX BOLT (C)
TILT BRACKET
ASSEMBLY
TILT ANCHOR
ASSEMBLY
FIGURE 6
1" WASHERS (EE)
1/8" x 1-1/2"
COTTER PIN (HH)
APPLY
GREASE
DUMP PIVOT
BRACKET
1/8" x 1-1/2"
COTTER PIN (HH)
FIGURE 7
5/8" WASHERS (BB)
5/8" WASHERS (BB)
1/8" x 1-1/4"
COTTER PIN (II)
1/8" x 1-1/4"
COTTER PIN (II) DUMP
CONTROL
ROD
1/8" x 1-1/4"
COTTER
PINS (II)
FIGURE 8
TILT STOP
BRACKET
1/4" NYLOCK
NUT (S)
1/4" WASHER (W) 1/4" x 3/4"
CARRIAGE BOLT (K)
FIGURE 9
STEP 8: INSTALL DUMP PIVOT BRACKET
(SEE FIGURE 7)
• Install a 1/8" x 1-1/2" cotter pin (HH) to the inside hole
in the shaft shown in gure 7, and then install a 1"
washer (EE) onto the shaft. Apply grease to the end of
the shaft and install the dump pivot bracket assembly
onto the shaft. Install a 1" washer (EE) onto the shaft
and secure it using a 1/8" x 1-1/2" cotter pin (HH).
STEP 9: INSTALL DUMP CONTROL ROD
(SEE FIGURE 8)
• Install a 1/8" x 1-1/4" cotter pin (II) into the inside hole
in each end of the dump control rod. Spread the ends
of the cotter pins and wrap around the rod. Install a
5/8" washer (BB) onto each end of the control rod.
• Install the dump control rod to the dump pivot bracket
and bucket. Fasten using two 5/8" washers (BB) and
1/8" x 1-1/4" cotter pins (II). Spread the ends of the
cotter pins and wrap around the rod.
STEP 10: INSTALL TILT STOP BRACKETS
(SEE FIGURE 9)
• Install a tilt stop bracket (OO) to each side of the
bucket using a 1/4" x 3/4" carriage bolt (K), 1/4"
washer (W) and 1/4" nylock nut (S). Do not tighten
the nuts until step 28.

9
5/16" x 1-3/4"
HEX BOLT (G)
5/16" NYLOCK
NUTS (R)
LIFT HANDLE
TUBE
INDEX
BRACKET
FIGURE 10
LIFT HANDLE
TUBE EXTENSION
1/4" NYLOCK NUT (S)
1/4" x 1-3/4"
HEX BOLT (H)
LIFT HANDLE
TUBE
FIGURE 11
FIGURE 12
INDEX ROD
LIFT CABLE (SHORT)
CABLE
ANCHOR
CABLE
ADJUSTMENT
NUTS
HOOK
LIFT TRIGGER
STEP 11: INSTALL LIFT HANDLE TUBE
(SEE FIGURE 10)
• Install the lift handle tube into the index bracket using
two 5/16" x 1-3/4" hex bolts (G) and 5/16" nylock nuts
(R).
STEP 12: INSTALL LIFT HANDLE TUBE EXTENSION
(SEE FIGURE 11)
• Install the lift handle tube extension on the lift handle
tube using a 1/4" x 1-3/4" hex bolt (H) and 1/4" nylock
nut (S).
STEP 13: INSTALL LIFT CABLE
(SEE FIGURE 12)
• Squeeze the lift trigger and slide the anchor end of the
lift cable (short) into the hole in the trigger. Release
the trigger and guide the cable through the slot in
the bottom of the trigger and trigger housing. Insert
the end of the plastic cable covering into the trigger
housing.
• Connect the hooked end of the lift cable into the index
rod, and install the threaded cable adjuster into the
notch in the top of the index bracket, placing a nut on
each side of the notch.
• Adjust the cable adjustment nuts so that when the
trigger is squeezed, the bottom of the index rod raises
enough to release from the latched position. The index
rod should also lower far enough to lock in the latched
position when the trigger is released.
• Attach the lift cable to the lift handle using three cable
ties (NN).

10
5/16"
NYLOCK
NUTS (R)
5/16" x 1-3/4"
HEX BOLTS (G)
5/16"
NYLOCK
NUT (R)
DUMP
HANDLE
TUBE
DUMP PIVOT
BRACKET
FIGURE 13
DUMP HANDLE
TUBE EXTENSION
DUMP HANDLE
TUBE
1/4" NYLOCK
NUT (S)
1/4" x 1-3/4"
HEX BOLT (H)
FIGURE 14
DUMP TRIGGER
DUMP CABLE (LONG)
FIGURE 15
STEP 14: INSTALL DUMP HANDLE TUBE
(SEE FIGURE 13)
• Install the dump handle tube to the dump pivot bracket
assembly using three 5/16" x 1-3/4" hex bolts (G) and
5/16" nylock nuts (R).
STEP 15: INSTALL DUMP HANDLE TUBE EXTENSION
(SEE FIGURE 14)
• Install the dump handle tube extension on the dump
handle tube using a 1/4" x 1-3/4" hex bolt (H) and 1/4"
nylock nut (S).
STEP 16: INSTALL DUMP CABLE
(SEE FIGURE 15)
• Squeeze the dump trigger and slide the anchor end
of the dump cable wire (long) into the hole in the
trigger. Release the trigger and guide the cable wire
through the slot in the bottom of the trigger and trigger
housing. Insert the end of the plastic cable covering
into the trigger housing.
• Attach the dump cable to the dump handle tube using
three cable ties (NN).

11
SPRING
SMALL 1/2" WASHER (Z)
CABLE
ADJUSTER
HOOK
DUMP CONTROL PIN
PIN STOP
BRACKET
3/4"
DUMP CONTROL PIN
PIN STOP
BRACKET
FIGURE 16
#10 x 5/8"
TRUSS
HEAD BOLT (L)
HOSE
CLIP (PP)
#10-32 NYLOCK
NUT (U)
5/16" x 1"
HEX BOLT (F)
SPACER
5/16"
NYLOCK
NUT (R)
FIGURE 17
INSTALL FRONT SCOOP ON TRACTOR
STEP 19: IDENTIFY YOUR TRACTOR TYPE
(SEE FIGURE 18)
• Look under the front of your tractor. If there is a single
mower deck suspension bracket located underneath
the middle of the front axle, go to page 12, step 20. If
your tractor does not have a mower deck suspension
bracket underneath the middle of the front axle, go
to page 13, step 22 or step 24 for tractors with dual
suspension brackets.
MOWER DECK
SUSPENSION
BRACKET
FIGURE 18
STEP 17: INSTALL DUMP CONTROL PIN
(SEE FIGURE 16)
• Install a small 1/2" washer (Z) and then the
compression spring (MM) onto the dump control pin.
Install the dump control pin into the pin stop bracket.
Make sure the at side of the pin faces to the front
when nished.
• Connect the hooked end of the dump cable into the
hole in the dump control pin. Install the threaded cable
adjuster down into the notch in the pin stop bracket,
placing a nut on each side of the notch. Adjust and
tighten the adjuster nuts so that the tapered end of
the dump control pin extends 3/4" through the side of
the pin stop bracket.
STEP 18: INSTALL HOSE CLIP AND SPACER
(SEE FIGURE 17)
• Secure the dump cable to the back of the bucket
using a hose clip (PP), a #10 x 5/8" truss-head bolt (L)
and a #10-32 nylock nut (U).
• Fasten the unused spacer to the lift frame to store it,
using a 5/16" x 1" hex bolt (F) and 5/16" nylock nut
(R). The spacer will be either the 3/8" spacer that was
supplied in the parts bag or the spacer it replaced in
step 7.

12
LEFT (LONG)
SIDE PLATE
5/16" x 1"
CARRIAGE BOLT (J)
5/16"
NYLOCK
NUT (R)
(3) 3/8" x 1"
CARRIAGE BOLTS (I)
(3) 3/8" NYLOCK
NUTS (Q)
ENGINE
MOUNTING
PLATE
(3) 1/2" LARGE
WASHERS (CC)
(SEE NOTE)
FIGURE 19
LAWN TRACTORS AND GARDEN TRACTORS
WITH SINGLE SUSPENSION BRACKETS
STEP 20: INSTALL SIDE PLATES
(SEE FIGURE 19)
• Remove any bolts present in the mounting holes on
the left side of the tractor frame. Do not remove bolts
from right side of frame until left side plate has been
installed.
• Install the left (long) side plate on the tractor frame
using three 3/8" x 1" carriage bolts (I), three 3/8"
nylock nuts (Q), one 5/16" x 1" carriage bolt (J), one
5/16" nylock nut (R) and three large 1/2" washers
(CC) if needed (see note). Do not tighten yet. Repeat
for the right side plate.
NOTE: If an engine mounting plate is present (shown
with dotted lines) that prevents the side plate from resting
at against the tractor frame, place 1/2" washers (CC) on
the front two bolts and the rear bolt as shims between the
side plate and the frame.
1/2" NYLOCK
NUT (N)
FRAME BRACE
HOLE FOR LT
HOLE FOR GT
1/2" x 1-3/4"
HEX BOLT (B)
1/2" SPACER (JJ)
1/2" LARGE
WASHER (CC)
STEP 21: INSTALL FRAME BRACE
(SEE FIGURE 20)
• Install the frame brace to the inside of the side plates
using two 1/2" x 1-3/4" bolts (B), large 1/2" washers
(CC), 1/2" spacers (JJ) and 1/2" nylock nuts (N).
Install the brace in the bottom holes for Garden (GT)
Tractors and the second from bottom holes for Lawn
(LT) Tractors. Do not tighten yet.
• Tighten all nuts on side plates and frame brace.
• Skip to step 25 on page 14.
FIGURE 20

13
(2) 3/8" x 1"
HEX BOLTS (E)
LEFT (GT)
SIDE PLATE
(2) 3/8" LOCK
WASHERS (V)
LONG
HAIRPIN
COTTER (FF)
3/4" WASHER (DD)
FIGURE 23
STEP 24: INSTALL SIDE PLATES
(SEE FIGURE 23)
• Remove any bolts present in the mounting holes on
the left side of the tractor frame. Do not remove bolts
from right side of frame until left side plate has been
installed.
• Install the left (short) side plate with the pin to the
outside using two 3/8" x 1" hex bolts (E) and 3/8" lock
washers (V). Tighten only until bolts are snug and lock
washers are attened. Repeat for the right side plate.
• Install a 3/4" washer (DD) and a long hairpin cotter
(FF) to the pin in each side plate. Remove them while
mounting the scoop.
GARDEN TRACTORS WITH DUAL
SUSPENSION BRACKETS
FIGURE 22
1/2" NYLOCK NUT (N)
FRAME BRACE
1/2" x 1-3/4"
HEX BOLT (B)
1/2" SPACER (JJ)
1/2" LARGE
WASHER (CC)
STEP 23: INSTALL FRAME BRACE
(SEE FIGURE 22)
• Install the frame brace between the side plates using
two 1/2" x 1-3/4" bolts (B), large 1/2" washers (CC),
1/2" spacers (JJ) and 1/2" nylock nuts (N). Fasten the
brace to the second from bottom holes in the side
plates. Tighten.
• Tighten 3/8" bolts (E) in side plates only until they are
snug and the lock washers are attened.
• Skip to step 25 on page 14.
LAWN TRACTORS WITH DUAL SUSPENSION
BRACKETS
LEFT (LONG)
SIDE PLATE
(3) 3/8" x 1"
HEX BOLTS (E)
(3) 3/8" SMALL
WASHERS (Y)
3/8" LARGE
WASHER (AA)
(if needed)
(3) 3/8" LOCK
WASHERS (V)
FIGURE 21
STEP 22: INSTALL SIDE PLATES
(SEE FIGURE 21)
• Remove any bolts present in the mounting holes on the
left side of the tractor frame. Do not remove bolts from
right side of frame until done with left side plate.
• Fasten the left (long) side plate to the tractor frame using
three 3/8" x 1" hex bolts (E), 3/8" small washers (Y), and
3/8" lock washers (V). If there is a bracket like the one
shown with dotted lines, use a 3/8" large washer (AA) as
a shim on the rear bolt. Do not tighten yet.

14
TIGHTEN TILT BRACKET
DUMP
CONTROL PIN
PIN STOP BRACKET
FIGURE 25
STEP 26: ADJUST TILT BRACKET ASSEMBLY
(SEE FIGURE 25)
• Lower the scoop assembly onto a smooth level
surface. For normal use, let the bottom of the bucket
rest at on the ground. For more aggressive scraping
action, place 1/4" shims under the rear of the bucket
at each end.
• Swing the tilt bracket forward to check for clearance
with the pin stop bracket. There should be a small
gap between the tilt bracket and the side of the pin
stop bracket. If not, adjust the position of the pin stop
bracket side to side.
• Make sure the two bolts in the tilt bracket are loose
enough to turn by hand. Align the tilt bracket so that
the dump control pin snaps into the hole in the tilt
bracket. The tapered end of the pin should extend
clear through the tilt bracket. Tighten the two bolts
and nuts in the tilt bracket.
LONG
HAIRPIN
COTTER (FF)
ATTACHMENT
ROD
SCOOP
ASSEMBLY
BOLT OR PIN
DUMP HANDLE
FIGURE 24
STEP 25: MOUNT SCOOPTO TRACTOR
(SEE FIGURE 24)
• Align the scoop with the side plates on the front of the
tractor. Lift the rear of the scoop and slide the notches
in the scoop frame onto the bolts or pins in the tractor
side plates. Stand on the left side of the tractor and
push down on the scoop dump handle until the holes
in the scoop frame and the holes in the side plates are
aligned. Install the attachment rod through the holes
from the left side and secure it with a long hairpin
cotter (FF).
INSTRUCTIONS FOR ALLTRACTORS

15
TIGHTEN
NUTS
LIFT STRAP
ASSEMBLIES
LIFT HANDLE
TILT STOP
BRACKET
LIFT FRAME ARM
FIGURE 26
FIGURE 27
STEP 27: ADJUST LIFT STRAPS
(SEE FIGURE 26)
• Make sure the nuts and bolts in the lift straps are
loose enough to turn by hand. Stand on the right side
of the scoop and hold the lift handle as far forward
as it will go while you tighten one of the nuts in the lift
straps.You can let go of the lift handle to tighten the
other three nuts in the lift straps.
STEP 28: ADJUST TILT STOP BRACKETS
(SEE FIGURE 26)
• Raise the scoop until it locks in the TRANSPORT
position. Push the tilt stop brackets (OO) on each side
of the bucket down against the lift frame arms, and
tighten the nuts.
STEP 29: CHECK DUMPING OPERATION
• With the scoop in the transport position, squeeze the
dump trigger and push down on the dump handle
to dump the bucket. Release the dump trigger and
lift up on the handle to lock the bucket in the upright
position. If the dump control pin passes underneath
the tilt bracket instead of locking into it, move the pin
stop bracket on top of the bucket farther towards the
rear. If this does not work, repeat steps 26, 27 and 28.

16
• Always test to make sure your vehicle has adequate
power and braking capabilities whenever hauling a
substantial amount of weight in your front end scoop.
Use extra caution when operating on slopes.
• For best handling and traction, distribute the weight of
the load evenly in the bucket.
CAUTION: Never ram the scoop into
material at high speeds.
• Keep the lift handle locked in the raised position when
tilting the scoop bucket forward to dump.
• The lift handle must be locked in the raised position to
allow the dump handle to lock the scoop bucket back
in the upright position after dumping.
• Do not scrape or push material with the scoop bucket
while it is tilted forward.
• Add wheel weights for improved traction when using
the scoop.
• To dump material from the bucket, squeeze the dump
trigger and push the dump tube handle down. Release
the trigger before returning the bucket to the upright
position.
• To lower the bucket, squeeze the lift trigger and
then lift up on the lift handle. If the trigger is hard
to depress, you may need to push down on the lift
handle while squeezing, and then lift up. Release
the trigger before retuning the bucket to the raised
position.
• Do not exceed mowing speed (3 mph) when the front
end scoop is attached to the tractor.
CAUTION: To avoid possible injury, make
sure that no one is near the bucket before
dumping the bucket.
CAUTION: Always lower the scoop bucket
to the ground before leaving the tractor.
OPERATION
KNOW YOUR FRONT END SCOOP
Read this owner's manual and safety rules before
operating your front end scoop.
Compare the illustration below with your front end scoop
to familiarize yourself with the various controls and their
locations.
LIFT
HANDLE
DUMP
HANDLE
DUMP
TRIGGER
LEVER
LIFT
TRIGGER
LEVER
DUMP TRIGGER LEVER Press to release the dump pin.
DUMP HANDLE Press down to dump the bucket.
LIFT TRIGGER LEVER Press to release the index pin.
LIFT HANDLE Press down to lift the bucket assembly.
HOW TO USE YOUR SCOOP
DO NOT EXCEED 200 LB. CAPACITY OF BUCKET
One cubic foot of dirt weighs approximately 80 lbs.
One cubic foot of dry sand or gravel weighs
approximately 100 lbs.
CAUTION: Vehicle braking and stability
may be affected with the addition of an
accessory or an attachment. Be aware of
changing conditions on slopes.
• Refer to the vehicle owner's manual for instructions on
safe operation on slopes.
• Use the slope guide provided on page 23 of this
manual to determine whether slope angle is too steep
for safe operation.

17
PROBLEM CAUSE CORRECTION
Scoop won't lock into
raised/transport position.
Scoop bucket won't lock into level
position
Lift handle trigger won't release
scoop from the transport position.
Dump handle trigger won't
release bucket to dump
Bucket is becoming more difcult
to tilt up or down.
1. Index rod is jamming.
2. Frame is hitting tilt stop
brackets.
1. Dump control pin is not aligned
with the tilt bracket
1. Index rod is jamming.
2. Lift cable is not adjusted properly
1. Dump control cable is not adjusted
properly
2. Latch mechanism is not adjusted
properly.
1. Debris is lodged between bucket
assembly and lift frame.
1. Apply grease to the bottom slot in the
lift bracket, where the index rod slides
2. Adjust the tilt stop brackets as
instructed on page 15.
1. Adjust the tilt bracket and lift straps as
instructed on pages 14 and 15.
1. Apply grease to the bottom slot in the
lift bracket, where the index rod slides.
2. Adjust cable nuts as instructed on page
9.
1. Adjust parts as instructed for gure 15
on page 10.
2. Adjust parts as instructed for gure 16
on page 11.
1. Remove all debris from between the
bucket assembly and the lift frame.
TROUBLESHOOTING
MAINTENANCE
CHECK FOR LOOSE FASTENERS
•Before each use make a thorough visual check of
the front end scoop for any bolts and nuts which may
have loosened. Retighten any loose bolts and nuts.
CLEANING
• After each use, clean off any dirt and debris from the
scoop bucket lift frame.
• Before storing at the end of each season, rinse off
the scoop bucket and scoop lift frame. Allow to dry
thoroughly. Paint any exposed metal surfaces to
protect from rust.
• Store in a clean, dry area.
LUBRICATION
• Lightly oil all pivot points on the scoop lift mechanism.
• Lightly oil the surface on the scoop bucket where the
attachment lift frame pivots.
• Apply a good grade of spray lubricant to the trigger
assemblies on the lift handle and dump handle.

18
37
36
22
84
34
30
31 32
33 83
81
5
4
38
1
10
6
87
39
29
19
45
2
1
7
8
6
9
79
78
75
77
11
12
13
51
76
17
18
73
14
15
2021
16
22
15
15
28
13
27
28
19 42 43 44
45 52
24
26
72
1
25
48 6315
14 71
46
47 15
49
14
10
43 42
13
13
5245
51
42
51 52
45
43
41
54
45
52
40
32
21
70
50
20 56
57
58
68
17
66
65
64 63
14 35
61
60
59
52 45
6710
13
68
62
10
3
75
74
53
67
82 29
80
69
13
14
31
85
23
23
44
26
55
REPAIR PARTS FOR MODEL 45-0403 FRONT END SCOOP

19
REPAIR PARTS FOR MODEL 45-0403 FRONT END SCOOP
* Purchase Common Hardware Locally
REF PART QTY DESCRIPTION
NO. NO.
1 1509-69 3 Hex Bolt, 1/4-20 x 1-3/4" (Grade 5)
2 726-0178 6 Cable Tie
3 49265 1 Lift Handle Extension
4 49266 2 Oval Screw, 10-24 x 1-1/2"
5 47674 2 Plastic Plug, 1-1/4" O.D. Tube
6 47554 2 Trigger Housing Assembly
7 712-0127 2 Square Nut, #10-24
8 47317 2 Grip, Black
9 47555 1 Cable, Lift
10 47189 5 Nylock Nut, 1/4"
11 47369 1 Roll Pin, 3/16" x 1-3/4"
12 47368 1 Roll Pin, 5/16" x 1-3/4"
13 47810 14 Nylock Nut, 5/16-18
14 HA21362 14 Nylock Nut, 3/8-16
15 43070 12 Flat Washer, 3/8"
16 25350 4 Lift Strap
17 43063 7 Hex Bolt, 5/16-18 x 1" (Grade 5)
18 25343 1 Lift Bracket
19 741-0192 2 Flange Bearing with Flats
20 R19171616 4 Flat Washer, 1/2" x 1" (Small)
21 43055 4 Hairpin Cotter, 3/32" x 1.8"
22 43001 10 Hex Bolt, 3/8-16 x 1" (Grade 5)
23 63755 2 Trigger Assembly
24 43178 1 Hex Nut, 1/4-20
25 64964 1 Tilt Anchor Assembly
26 48115 3 Nylock Jam Nut, 1/2-13
27 63675 1 Lift Arm Assembly
28 25510 2 Mounting Bracket
29 43343 3 Hairpin Cotter, 3/32" x 2-5/16"
30 R74780828 2 Hex Bolt 1/2-13 x 1-3/4" (Grade 5)
31 R19172410 8 Flat Washer, 1/2" x 1-1/2" (Large)
32 24817 4 Spacer, 0.52" x 0.75" x 0.5"
33 712-3083 2 Nylock Nut, 1/2-13
34 43003 6 Lock Washer, 3/8"
35 712-0261 2 Nylock Nut, 5/8-11
36 63568 1 Right (Short) Side Plate
37 63569 1 Left (Short) Side Plate
38 49270 1 Dump Handle Tube Extension
39 47066 1 Attachment Rod
40 49271 1 Dump Handle Tube
41 49483 1 Dump Control Cable
42 43601 3 Washer, 1.59" x 1.032" x 0.60"
43 43093 3 Cotter Pin, 1/8" x 1-1/2"
44 710-0865 3 Hex Bolt, 1/2-13 x 1" (Grade 5)
REF PART QTY DESCRIPTION
NO. NO.
45 R19212016 6 Flat Washer, 5/8" x 1-1/4" x 16 Ga.
46 25362 1 Tilt Bracket Extension Strap
47 64983 1 Tilt Bracket
48 HA6441 1 Hex Bolt, 3/8-16 x 2" (Grade 5)
49 41576 1 Hex Bolt, 3/8-16 x 1-3/4" (Grade 5)
50 64963 1 Lift Frame Assembly
51 43084 5 Hex Bolt, 5/16-18 x 1-3/4" (Grade 5)
52 43010 6 Cotter Pin, 1/8" x 1-1/4"
53 64968 1 Dump Pivot Bracket
54 49273 1 Dump Control Rod
55 49268 1 Dump Control Pin
56 48905 1 Compression Spring
57 46055 1 Spring Pin, 1/8" x 1"
58 25335 1 Pin Stop Bracket
59 47171 1 Nylock Nut, #10-32
60 HA23761 1 Hose Clamp
61 43346 1 Truss-Head Bolt #10-32 x 5/8"
62 64962 1 Bucket Assembly
63 43015 3 Hex Nut, 3/8-16
64 43087 2 Hex Bolt, 3/8-16 x 1-1/4" (Grade 5)
65 44950 2 Carriage Bolt, 1/4-20 x 3/4" (Grade 5)
66 25331 2 Tilt Stop Bracket
67 736-0142 3 Flat Washer, 1/4"
68 43081 8 Flat Washer, 5/16"
69 44326 2 Carriage Bolt, 5/16" x 1" (Grade 5)
70 710-0367 2 Hex Bolt, 5/8-11 x 1-1/2" (Grade 5)
71 25408 1 Spacer, 3/8" I.D. x 7/8" O.D. x 3/8"
23625 1 Spacer, 3/8" I.D. x 5/8" O.D. x 1/4"
72 43000 1 Extension Spring
73 44062 2 Clevis Pin, 1/2" x 1"
74 142 1 Cotter Pin, 1/8" x 3/4"
75 R19131316 2 Flat Washer, 3/8" x 13/16" x 1/16"
76 63773 1 Index Bracket Assembly
77 48049 1 Index Rod
78 732-0306 1 Spring, Compression
79 49264 1 Lift Handle Tube
80 43009 2 Flat Washer, 3/4"
81 25562 1 Right (Long) Side Plate
82 25563 1 Left (Long) Side Plate
83 25722 1 Frame Brace
84 43350 6 Bolt, Carriage 3/8-16 x 1" (Grade 5)
85 736-0235 2 Washer, .375" x 1.26" x .172"
40121 1 Owner's Manual

20
NOTES